Uploaded November 2024 | Updated September 2026, 2 weeks ago
One of my goals is to promote functional 3D printing too. Don't get me wrong, I like printing toys and figures (that's fun too), but printing functional parts gives another level to our 3D printer. I asked 3D printing YouTubers for a video of about half a minute in length, showcasing their favorite functional 3D-printed creation(s).
NEW! POLYMAKER offered 2x$100 filament vouchers for the participants from the second part (by community)! More info down.
(Dear Patreons, I contacted everybody You suggested, but as you can see, the reply was only 15%)
Youtubers from this video:
TADA 3D Printing: youtube.com/@tada3dprinting
Design Prototype Test: youtube.com/@DesignPrototypeTest
Functional Print Friday: youtube.com/@FunctionalPrintFriday
Geek Detour: youtube.com/@GeekDetour
gerGO PRINT 3D: youtube.com/@gerGoPrint3D
Hoffman Tactical: youtube.com/@HoffmanTactical
JanTec Engineering: youtube.com/@JanTecEngineering
ModBot: youtube.com/@ModBotArmy
My Tech Fun: youtube.com/@MyTechFun
NeedItMakeIt: youtube.com/@NeedItMakeIt
Robert Cowan: youtube.com/@RobertCowanDIY
Ruiraptor: youtube.com/@ruiraptor
Teaching Tech: youtube.com/@TeachingTech
The Next Layer: youtube.com/@thenextlayer
Chapters:
0:00 Introduction
1:31 @tada3dprinting
2:00 @DesignPrototypeTest
2:31 @FunctionalPrintFriday
3:44 @GeekDetour
4:18 @gerGoPrint3D
4:48 @HoffmanTactical
5:13 @JanTecEngineering
5:32 @ModBotArmy
5:56 @MyTechFun
6:37 @NeedItMakeIt
7:18 @RobertCowanDIY
8:12 @ruiraptor
8:47 @TeachingTech
9:19 @thenextlayer
10:01 Outro
------------------
About the second part of this video:
New info!!! POLYMAKER offered 2x$100 filament vouchers, it will be random draw from participants after the video is published!
As mentioned in the Outro, there will be a second part of this video, but this time by community. If You have some interesting 3D printed part (it can be your own design or downloaded), present it in 30 second video.
The deadline is: 2024-12-15
Technical requirements for the video:
Resolution: Full HD (1920 x 1080) , 30 FPS
Length: approximately 30 seconds.
Don't send it as attachment in email (it will be too big). Use Google Drive, PCloud Transfer, WeTransfer etc.
Suggestion for the content of your video: short introduction, You can mention your country. Present the object, what material you used, printing time etc.
Contact email you can find on YT/about page:
Use "Functional 3DP" in description or subject or comment of that message during the upload.
------------------------------
#3dprinting
One of my goals is to promote functional 3D printing too. Don't get me wrong, I like printing toys and figures (that's fun too), but printing functional parts gives another level to our 3D printer. I asked 3D printing YouTubers for a video of about half a minute in length, showcasing their favorite functional 3D-printed creation(s).
NEW! POLYMAKER offered 2x$100 filament vouchers for the participants from the second part (by community)! More info down.
(Dear Patreons, I contacted everybody You suggested, but as you can see, the reply was only 15%)
Youtubers from this video:
TADA 3D Printing: youtube.com/@tada3dprinting
Design Prototype Test: youtube.com/@DesignPrototypeTest
Functional Print Friday: youtube.com/@FunctionalPrintFriday
Geek Detour: youtube.com/@GeekDetour
gerGO PRINT 3D: youtube.com/@gerGoPrint3D
Hoffman Tactical: youtube.com/@HoffmanTactical
JanTec Engineering: youtube.com/@JanTecEngineering
ModBot: youtube.com/@ModBotArmy
My Tech Fun: youtube.com/@MyTechFun
NeedItMakeIt: youtube.com/@NeedItMakeIt
Robert Cowan: youtube.com/@RobertCowanDIY
Ruiraptor: youtube.com/@ruiraptor
Teaching Tech: youtube.com/@TeachingTech
The Next Layer: youtube.com/@thenextlayer
Chapters:
0:00 Introduction
1:31 @tada3dprinting
2:00 @DesignPrototypeTest
2:31 @FunctionalPrintFriday
3:44 @GeekDetour
4:18 @gerGoPrint3D
4:48 @HoffmanTactical
5:13 @JanTecEngineering
5:32 @ModBotArmy
5:56 @MyTechFun
6:37 @NeedItMakeIt
7:18 @RobertCowanDIY
8:12 @ruiraptor
8:47 @TeachingTech
9:19 @thenextlayer
10:01 Outro
------------------
About the second part of this video:
New info!!! POLYMAKER offered 2x$100 filament vouchers, it will be random draw from participants after the video is published!
As mentioned in the Outro, there will be a second part of this video, but this time by community. If You have some interesting 3D printed part (it can be your own design or downloaded), present it in 30 second video.
The deadline is: 2024-12-15
Technical requirements for the video:
Resolution: Full HD (1920 x 1080) , 30 FPS
Length: approximately 30 seconds.
Don't send it as attachment in email (it will be too big). Use Google Drive, PCloud Transfer, WeTransfer etc.
Suggestion for the content of your video: short introduction, You can mention your country. Present the object, what material you used, printing time etc.
Contact email you can find on YT/about page:
Use "Functional 3DP" in description or subject or comment of that message during the upload.
------------------------------
#3dprinting
