Uploaded May 2017 | Updated November 2026, 2 hours ago
This video shows how to replace a blade on a riding lawn mower. A dull or bent mower blade tatters grass tips rather than making a clean cut, leaving the lawn looking dull. A bent blade creates vibrations that can vibrate and damage the mandrel assembly. Replace the blade with a part that fits your model if it's dull or bent.
Visit us at:
https://www.searspartsdirect.com?sid=soc:youtube:replacing-the-blade-on-a-riding-lawn-mower
Or call 1-800-437-1673 to speak with a parts specialist.
The video includes these parts and tools. Look up your model to make sure you get the right parts for your mower.
Blade
searspartsdirect.com/part-number/422719/0071/917.html?sid=soc:youtube:direct-part-link
Find riding mower parts at
searspartsdirect.com/partsdirect/product-types/Riding-mower-tractor-Parts?sid=soc:youtube:riding-mower-parts
Or click here to schedule an appointment with a repair technician.
searshomeservices.com/repair#showall
Transcript:
The first step to replacing the blade is to turn the ignition switch off and remove the key. Lift the mower hood and disconnect the spark plug wire. Lower the mower deck to its lowest position. Disengage the cutting blades. Roll the blade belt off the engine pulley and release the belt from the belt keepers. Remove the front lift link support retaining pin and washer and then detach the support from the deck. Remove the left suspension arm retaining clip and then detach the arm from the mower frame. Remove the left rear deck bracket retaining clip and washer and then release the bracket from the deck. Repeat the process on the other side of the deck to disconnect the right suspension arm and right rear deck bracket. Pull the deck out far enough to access the blade cable attached to the deck. Release the locking tabs and pull the blade cable out from the deck bracket. Disconnect the blade cable spring from the idler arm and move the cable aside. Pull the deck out from under the mower frame and flip it over. Put a wood block between the blade and mower deck to keep the cutting blade from moving. Remove the blade mounting bolt and pull off the cutting blade. With the correct side of the blade facing up, attach the blade to the blade shaft and hand tighten the blade bolt. Put the wood block back in place and tighten the blade bolt firmly. Remove the wood block and flip the deck upright. Push the deck near the mower frame. Connect the blade clutch cable spring to the idler arm. Push the blade clutch cable retainer into the deck bracket and engage the locking tabs. Position the deck under the mower frame. Reconnect the front lift link support to the deck using the washer and retaining clip. Reconnect the left suspension arm and deck bracket using the washers and retaining clips. Repeat the process to reconnect the right suspension arm and deck bracket. Route the blade belt through the belt keepers and roll the blade belt onto the engine pulley. Reconnect the spark plug wire and lower the mower hood.
This video shows how to replace a blade on a riding lawn mower. A dull or bent mower blade tatters grass tips rather than making a clean cut, leaving the lawn looking dull. A bent blade creates vibrations that can vibrate and damage the mandrel assembly. Replace the blade with a part that fits your model if it's dull or bent.
Visit us at:
https://www.searspartsdirect.com?sid=soc:youtube:replacing-the-blade-on-a-riding-lawn-mower
Or call 1-800-437-1673 to speak with a parts specialist.
The video includes these parts and tools. Look up your model to make sure you get the right parts for your mower.
Blade
searspartsdirect.com/part-number/422719/0071/917.html?sid=soc:youtube:direct-part-link
Find riding mower parts at
searspartsdirect.com/partsdirect/product-types/Riding-mower-tractor-Parts?sid=soc:youtube:riding-mower-parts
Or click here to schedule an appointment with a repair technician.
searshomeservices.com/repair#showall
Transcript:
The first step to replacing the blade is to turn the ignition switch off and remove the key. Lift the mower hood and disconnect the spark plug wire. Lower the mower deck to its lowest position. Disengage the cutting blades. Roll the blade belt off the engine pulley and release the belt from the belt keepers. Remove the front lift link support retaining pin and washer and then detach the support from the deck. Remove the left suspension arm retaining clip and then detach the arm from the mower frame. Remove the left rear deck bracket retaining clip and washer and then release the bracket from the deck. Repeat the process on the other side of the deck to disconnect the right suspension arm and right rear deck bracket. Pull the deck out far enough to access the blade cable attached to the deck. Release the locking tabs and pull the blade cable out from the deck bracket. Disconnect the blade cable spring from the idler arm and move the cable aside. Pull the deck out from under the mower frame and flip it over. Put a wood block between the blade and mower deck to keep the cutting blade from moving. Remove the blade mounting bolt and pull off the cutting blade. With the correct side of the blade facing up, attach the blade to the blade shaft and hand tighten the blade bolt. Put the wood block back in place and tighten the blade bolt firmly. Remove the wood block and flip the deck upright. Push the deck near the mower frame. Connect the blade clutch cable spring to the idler arm. Push the blade clutch cable retainer into the deck bracket and engage the locking tabs. Position the deck under the mower frame. Reconnect the front lift link support to the deck using the washer and retaining clip. Reconnect the left suspension arm and deck bracket using the washers and retaining clips. Repeat the process to reconnect the right suspension arm and deck bracket. Route the blade belt through the belt keepers and roll the blade belt onto the engine pulley. Reconnect the spark plug wire and lower the mower hood.










