How to Make a Sloper Prior to Knitting Your Sweater @SuzanneBryan
How to Make a Sloper Prior to Knitting Your Sweater  @SuzanneBryan
Uploaded February 2020 | Updated November 2026, 9 hours ago
How to make a sloper — a sew-up of the schematic in a fabric that behaves like knitting — to check the fit of a drop-shoulder sweater knit in pieces before casting on. This is part of a series on measurements, a schematic, a gauge swatch, and yardage, and is in conjunction with the ITAG Bottom Up / Drop Shoulder tutorial. Transfer the schematic measurements onto 1-inch gridded interfacing (or 1-inch graph paper), which is available at fabric stores. The body piece is half the circumference, not the full width. When cutting out, leave selvages only where the pieces will be seamed on a sewing machine; the wrist needs no selvage. If a neck trim or ribbing will be added, account for that width at the back neck, because it is not yet in the schematic outline. Waist shaping, if wanted, is typically marked about 3 inches above and below the waist. How much shaping, and whether it sits above, below, or both, depends on the bust and the hips. The marks on the sloper may look like a sharp angle, but knitted fabric gives, and the shaping is often worked inside the fabric rather than at the side edge, which makes a nicer seam. Sew the sloper in a jersey knit that stretches more from side to side than from top to bottom — a little heavier than T-shirt fabric works well — and try it on. In the example, excess fabric at the underarm was improved by planning about 1½ inches of shoulder short rows, then moving the whole sleeve down by the same amount so the arm does not get tighter. Waist shaping can be pinned and moved. Shaping only on the back, and not on the front, can add shape without accentuating the abdomen. A sloper is especially useful for a sweater knit in pieces, which cannot be tried on as it is worked. An alternative is to measure a sweater that already fits the way it should, and use those measurements — and it is still useful to turn those into a sloper and try it on, so the waist shaping is not a guess.

Chapters
0:15 Introduction: a sloper to check the fit before knitting
0:18 Transferring the schematic onto gridded interfacing
2:05 Back neck (account for neck trim)
2:36 Waist shaping (about 3 inches above and below)
4:28 Drafting the sleeve, and leaving selvages for seams
6:23 Trying on the sloper
7:11 Shoulder short rows, and moving the sleeve down
8:06 Testing waist shaping with pins
9:16 TIP: back-only waist shaping, if you do not want to accentuate the abdomen
10:28 Why make a sloper (especially for a sweater knit in pieces)
11:09 Use a fabric that behaves like knitting (jersey)

Related videos
- How to Take Body Measurements for a Custom Raglan Sweater: youtu.be/kNZ1WS63qwA
- How to Take Body Measurements for a Yoke Sweater: youtu.be/U2gI_J01p9U
- How to Measure for Drop Shoulder Knitted Garments: youtu.be/8fr1CVaJQZM
- How to Make a Gauge Swatch for a Sweater (Don't Round Your Stitch Gauge): youtu.be/0nECq0TZS8E
- Calculating Yardage for a Sweater from a Swatch & Schematic: youtu.be/aEKhuYwib0Y
- How to Custom-Fit a Yoke When Bust and Arm Sizes Differ: youtu.be/EsggQilA5NI
- How to Compensate for a Bust vs Sleeve Size Discrepancy: youtu.be/AJywu6ECtIM

ITAG Bottom Up / Drop Shoulder Tutorial: ravelry.com/patterns/library/itag-bottom-up-drop-shoulder

More on this topic: see my playlist "Sweater Construction & Finishing: Seaming, Pockets, Steeks, Weaving in Ends" on the channel.

Live Zoom classes (Bootcamps): masteryourknitting.com

If you enjoy my videos please subscribe and consider buying me a coffee on Ko-fi - ko-fi.com/suzannebryan

Where to find me -



Suzanne - Off the Cuff - youtube.com/channel/UCQBgFUvQzjz1RUm9NsgEA1A

Knitting with Suzanne Bryan on Ravelry - ravelry.com/groups/knitting-with-suzanne-bryan

Knitting with Suzanne Bryan on FB- facebook.com/groups/1769286026429876

KnittingSuzanne on Ravelry - ravelry.com/people/KnittingSuzanne

Blog: knittingsuzanne.com

#sloper #sweaterfitting #dropshoulder #knitting #schematic
How to Make a Sloper Prior to Knitting Your SweaterITAG SIS Q&A Plus General Knitting StuffCatching up with Phrancko.com and Starting My ITAG SIS SweaterITAG Q&A 12/5/18How to Apply Knitted in Button Band PlacketsSuzanne - Off the Cuff 2/13/19How to Tink or Unknit an SSP (Slip Slip Purl Decrease)How to Join a Pocket Lining at the Side Edge (No Seam)ITAG Q&A 11/28/18Comparing Horizontal Seaming Methods (Mattress, Back Stitch, Slip Stitch Crochet)
Knitting with Suzanne Bryan |

How to Make a Sloper Prior to Knitting Your Sweater

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER