Uploaded August 2021 | Updated September 2026, 1 week ago
In this video I will show you how to install the direct drive extruder kit from Micro Swiss on any 3D printer that has the 2020 aluminum extrusion with v slot wheels on the X axis. Although this kit was originally intended for use with the Creality Ender 3 and CR-10 applications, it can be made to work with just about any printer.
This doesn't mean some additional work won't be necessary, however, I worked out some of the issues you might run into and hopefully my solutions work for you. I demonstrate the installation on a ANET ET5X printer and have designed a bunch of custom parts that you may or may not need for your application.
You can find those parts here:
► thingiverse.com/thing:4934569
Print the main fan shroud with the 40mm extruder fan face on your print bed. No supports necessary. Print the fan duct in the upright position. No supports necessary.
The fan shroud and fan duct should work with the different varieties of printers, it is not just a solution for non-creality printers. Even if you have a Creality printer, you can use the newly designed shroud and duct work as it will replace your Creality parts.
However, If you have a Creality CR-10 or Ender 3 then you will have a smooth install experience and do not need any custom parts if you do not want to print any. The Micro Swiss kit is well equipped and well designed, all of the parts are of high quality.
Keep in mind that once you install the kit you will likely need to make some firmware changes or slicer setting changes. I go through several of those changes, but don't forget to change your retraction settings in your slicer as well! Bowden tube set ups usually run ~5+mm of retraction whereas a direct drive set up will use around 1mm.
If you have any questions or comments please put them in the comment section and I will try to answer everyone!
Thanks for watching!
#3DPRINTER #DIY #MAKER
****************************************************************
If you enjoy and have benefited from my content and are feeling generous I would love your support! You can "buy me a coffee" here:
► paypal.com/donate/?hosted_button_id=V2T6MEFUGP73Y ☕
By supporting my channel you are encouraging me to continue with this time consuming endeavor. A lot of time goes into design work, building my projects, filming the videos, editing the videos, etc. Plus it all costs money! Your generosity goes a long way in helping me bring you better content as often as I can!
Follow me on Instagram!
► instagram.com/embraceracing 📷
If you liked this video, perhaps you will also enjoy some channels that I personally find inspiring and interesting...
DIY and MAKER:
► The Hacksmith
youtube.com/channel/UCjgpFI5dU-D1-kh9H1muoxQ
► Adam Savage Tested
youtube.com/channel/UCiDJtJKMICpb9B1qf7qjEOA
► Thomas Sanladerer
youtube.com/user/ThomasSanladerer
Car Content:
► Mighty Car Mods
youtube.com/channel/UCgJRL30YS6XFxq9Ga8W2J3A
► Drivetribe
youtube.com/channel/UChiwLDIBJrV5SxqdixMHm
In this video I will show you how to install the direct drive extruder kit from Micro Swiss on any 3D printer that has the 2020 aluminum extrusion with v slot wheels on the X axis. Although this kit was originally intended for use with the Creality Ender 3 and CR-10 applications, it can be made to work with just about any printer.
This doesn't mean some additional work won't be necessary, however, I worked out some of the issues you might run into and hopefully my solutions work for you. I demonstrate the installation on a ANET ET5X printer and have designed a bunch of custom parts that you may or may not need for your application.
You can find those parts here:
► thingiverse.com/thing:4934569
Print the main fan shroud with the 40mm extruder fan face on your print bed. No supports necessary. Print the fan duct in the upright position. No supports necessary.
The fan shroud and fan duct should work with the different varieties of printers, it is not just a solution for non-creality printers. Even if you have a Creality printer, you can use the newly designed shroud and duct work as it will replace your Creality parts.
However, If you have a Creality CR-10 or Ender 3 then you will have a smooth install experience and do not need any custom parts if you do not want to print any. The Micro Swiss kit is well equipped and well designed, all of the parts are of high quality.
Keep in mind that once you install the kit you will likely need to make some firmware changes or slicer setting changes. I go through several of those changes, but don't forget to change your retraction settings in your slicer as well! Bowden tube set ups usually run ~5+mm of retraction whereas a direct drive set up will use around 1mm.
If you have any questions or comments please put them in the comment section and I will try to answer everyone!
Thanks for watching!
#3DPRINTER #DIY #MAKER
****************************************************************
If you enjoy and have benefited from my content and are feeling generous I would love your support! You can "buy me a coffee" here:
► paypal.com/donate/?hosted_button_id=V2T6MEFUGP73Y ☕
By supporting my channel you are encouraging me to continue with this time consuming endeavor. A lot of time goes into design work, building my projects, filming the videos, editing the videos, etc. Plus it all costs money! Your generosity goes a long way in helping me bring you better content as often as I can!
Follow me on Instagram!
► instagram.com/embraceracing 📷
If you liked this video, perhaps you will also enjoy some channels that I personally find inspiring and interesting...
DIY and MAKER:
► The Hacksmith
youtube.com/channel/UCjgpFI5dU-D1-kh9H1muoxQ
► Adam Savage Tested
youtube.com/channel/UCiDJtJKMICpb9B1qf7qjEOA
► Thomas Sanladerer
youtube.com/user/ThomasSanladerer
Car Content:
► Mighty Car Mods
youtube.com/channel/UCgJRL30YS6XFxq9Ga8W2J3A
► Drivetribe
youtube.com/channel/UChiwLDIBJrV5SxqdixMHm
