Uploaded September 2026 | Updated November 2026, 3 hours ago
How to Fix Any NETGEAR Wi-Fi Router That Is Not Turning On
If your NETGEAR Wi-Fi router has no power at all—no lights, no LEDs, and no signs of activity—the problem is usually related to the electrical outlet, power adapter, power connection, or the router itself. Try these steps in order.
1. Check the Power Outlet
Plug a lamp or another working device into the same electrical outlet to make sure the outlet is providing power.
If the router is connected to a power strip or surge protector, temporarily connect it directly to a wall outlet.
You can also try a different wall outlet.
2. Check the Power Adapter
Disconnect the power adapter from both the wall and the back of the NETGEAR router.
Wait approximately 30 seconds, then reconnect both ends securely.
Inspect the adapter and cable for:
Frayed or damaged wires
Bent or damaged connectors
Loose connections
Burn marks
Unusual odors
Do not use a damaged power adapter.
3. Check the Router's Power Button
Some NETGEAR routers have a physical Power On/Off button.
Make sure the router is connected to power and press the power button once.
Wait 30–60 seconds to see whether the power light comes on.
4. Try Another Compatible Power Adapter
If the router remains completely dead, testing it with another compatible power adapter can help determine whether the original adapter has failed.
The replacement adapter must have the correct:
Output voltage
Current rating
Polarity
Connector size
Do not use an adapter simply because the connector fits. The wrong voltage or polarity can damage the router.
5. Perform a Complete Power Cycle
Disconnect the router's power adapter.
Temporarily disconnect the Ethernet cables as well.
Wait approximately 2–5 minutes.
Then connect only the power adapter and turn the router on.
Wait several minutes for the router to start.
If the lights return, reconnect the Ethernet cable and check your Internet connection.
6. Consider a Power Surge or Lightning Strike
If the router stopped working immediately after a thunderstorm, lightning strike, power outage, or electrical surge, the power adapter may have been damaged.
Testing the router with a properly matched, known-good power adapter can help determine whether the adapter or router is the problem.
7. Don't Factory-Reset a Completely Dead Router
If there are absolutely no lights on the router, a factory reset generally will not fix the problem.
A factory reset is useful when the router powers on but has configuration or connectivity problems. It will not normally repair a router that isn't receiving power.
8. If There Are Still No Lights
If you have confirmed that:
The electrical outlet works
The power adapter is connected correctly
The power button is turned on
A properly matched, known-good power adapter doesn't work
then the router may have a failed power supply or an internal hardware failure.
Do not open the router or attempt to repair its internal power circuitry. If the router is still under warranty, contacting NETGEAR support or the retailer may be the best option.
The exact power specifications, power-button location, and troubleshooting procedure can vary between NETGEAR models, so knowing the model number is helpful when diagnosing a completely dead router.
Disclaimer: As an Amazon Associate I earn from qualified purchases.
How to Fix Any NETGEAR Wi-Fi Router That Is Not Turning On
If your NETGEAR Wi-Fi router has no power at all—no lights, no LEDs, and no signs of activity—the problem is usually related to the electrical outlet, power adapter, power connection, or the router itself. Try these steps in order.
1. Check the Power Outlet
Plug a lamp or another working device into the same electrical outlet to make sure the outlet is providing power.
If the router is connected to a power strip or surge protector, temporarily connect it directly to a wall outlet.
You can also try a different wall outlet.
2. Check the Power Adapter
Disconnect the power adapter from both the wall and the back of the NETGEAR router.
Wait approximately 30 seconds, then reconnect both ends securely.
Inspect the adapter and cable for:
Frayed or damaged wires
Bent or damaged connectors
Loose connections
Burn marks
Unusual odors
Do not use a damaged power adapter.
3. Check the Router's Power Button
Some NETGEAR routers have a physical Power On/Off button.
Make sure the router is connected to power and press the power button once.
Wait 30–60 seconds to see whether the power light comes on.
4. Try Another Compatible Power Adapter
If the router remains completely dead, testing it with another compatible power adapter can help determine whether the original adapter has failed.
The replacement adapter must have the correct:
Output voltage
Current rating
Polarity
Connector size
Do not use an adapter simply because the connector fits. The wrong voltage or polarity can damage the router.
5. Perform a Complete Power Cycle
Disconnect the router's power adapter.
Temporarily disconnect the Ethernet cables as well.
Wait approximately 2–5 minutes.
Then connect only the power adapter and turn the router on.
Wait several minutes for the router to start.
If the lights return, reconnect the Ethernet cable and check your Internet connection.
6. Consider a Power Surge or Lightning Strike
If the router stopped working immediately after a thunderstorm, lightning strike, power outage, or electrical surge, the power adapter may have been damaged.
Testing the router with a properly matched, known-good power adapter can help determine whether the adapter or router is the problem.
7. Don't Factory-Reset a Completely Dead Router
If there are absolutely no lights on the router, a factory reset generally will not fix the problem.
A factory reset is useful when the router powers on but has configuration or connectivity problems. It will not normally repair a router that isn't receiving power.
8. If There Are Still No Lights
If you have confirmed that:
The electrical outlet works
The power adapter is connected correctly
The power button is turned on
A properly matched, known-good power adapter doesn't work
then the router may have a failed power supply or an internal hardware failure.
Do not open the router or attempt to repair its internal power circuitry. If the router is still under warranty, contacting NETGEAR support or the retailer may be the best option.
The exact power specifications, power-button location, and troubleshooting procedure can vary between NETGEAR models, so knowing the model number is helpful when diagnosing a completely dead router.
Disclaimer: As an Amazon Associate I earn from qualified purchases.










