Uploaded July 2014 | Updated November 2026, 2 days ago
Description: This is my L8ist finished project, an all-germanium guitar practice amplifier. Because the most popular Fuzz Boxes are built with early germanium transistors, amplifiers that use these transistors sound really Gr8 as well. The output is a meagre 200mW but that's ok for a practice amplifier. I've gone even further and included an attenuator network between the output transformer secondary and speaker. If you're a bit of a nocturnal, like me, even 200mW can wake your family up so the inclusion of an attenuator means that a guitarist using it, or me, can continue practicing without the issues of waking up your peeps. The attenuator maintains a fixed load of 3.2 ohms, so as far as the amp circuit is concerned, it's still working into its recommended impedance. When set to maximum, the resistor network is disconnected, output transformer secondary is directly speaker coupled, so the amp behaves exactly as it would in a conventional set up. In addition, I've included a bit of post 90's tech: an LED. The LED is wired in such a way that it doesn't cause any unnecessary battery drain. The LED inserts a 2 volt drop, which is required for the pre-amp transistor: an AC113 low noise device. This also means the LED flickers a bit when the guitar is played but it's no problem @ all: in fact serves as a mini light show. Transistor line-up 1/. AC113, 2/. AC128, 3/. 2SB77 x 2: a gain matched pair. It is a similar circuit to another 1W germanium amp kit that retails for over £100. The main difference, apart from the output level, is that my design will work from any voltage from about 5 volts to 12 volts, whereas the £100 needs a precision 9 volts. This is owing to my inclusion of a temperature compensation diode that sets the bias for the two 2SB77s. @ a L8a occasion, I intend fitting a 6.2 mm jack socket so the unit can serve as a fuzz box, thus preserving this unique overdriven germanium sound. Love it!
Description: This is my L8ist finished project, an all-germanium guitar practice amplifier. Because the most popular Fuzz Boxes are built with early germanium transistors, amplifiers that use these transistors sound really Gr8 as well. The output is a meagre 200mW but that's ok for a practice amplifier. I've gone even further and included an attenuator network between the output transformer secondary and speaker. If you're a bit of a nocturnal, like me, even 200mW can wake your family up so the inclusion of an attenuator means that a guitarist using it, or me, can continue practicing without the issues of waking up your peeps. The attenuator maintains a fixed load of 3.2 ohms, so as far as the amp circuit is concerned, it's still working into its recommended impedance. When set to maximum, the resistor network is disconnected, output transformer secondary is directly speaker coupled, so the amp behaves exactly as it would in a conventional set up. In addition, I've included a bit of post 90's tech: an LED. The LED is wired in such a way that it doesn't cause any unnecessary battery drain. The LED inserts a 2 volt drop, which is required for the pre-amp transistor: an AC113 low noise device. This also means the LED flickers a bit when the guitar is played but it's no problem @ all: in fact serves as a mini light show. Transistor line-up 1/. AC113, 2/. AC128, 3/. 2SB77 x 2: a gain matched pair. It is a similar circuit to another 1W germanium amp kit that retails for over £100. The main difference, apart from the output level, is that my design will work from any voltage from about 5 volts to 12 volts, whereas the £100 needs a precision 9 volts. This is owing to my inclusion of a temperature compensation diode that sets the bias for the two 2SB77s. @ a L8a occasion, I intend fitting a 6.2 mm jack socket so the unit can serve as a fuzz box, thus preserving this unique overdriven germanium sound. Love it!










