Uploaded February 2026 | Updated November 2026, 8 hours ago
In this Autodesk Fusion tutorial, you’ll design a robust fastener ring that lets a 3D printed part clamp securely onto an E26 lamp socket using M4 set screws and captive square nuts. You’ll work in hybrid mode, project reference geometry for clean sketches, build a parametric ring you can refine later, and pull in accurate hardware models from McMaster-Carr as STEP files to validate fit and assembly.
Chapters
00:00 Overview: attaching a 3D printed part to a cylindrical lamp socket
00:24 Why a set-screw clamp is better than relying on plastic threads
00:42 Insert components in Fusion (hybrid mode) and create the fastener ring component
00:59 Create an offset plane for a clean sketch setup
01:13 Project key rings and hide clutter to simplify the sketch
01:34 Sketch ring diameters and add clearance for sliding onto the socket
01:53 Extrude the ring (10 mm) and check placement against the socket
02:09 Create a tangent plane and sketch the set screw hole location
02:27 Size and constrain the hole (M4 clearance) so it’s properly centered
02:55 Add space for the socket cap (counterbore clearance)
03:23 Cut additional depth so the cap area seats cleanly
03:39 Create the captive square nut pocket for an M4 square nut
04:51 Insert an M4 socket head screw from McMaster-Carr (STEP) and joint it in place
05:36 Insert an M4 square nut from McMaster-Carr (STEP) and lock it with a rigid joint
06:39 Iterate with parametric edits to improve screw engagement and ring size
07:20 Circular pattern the set-screw features (3x) around the center axis
07:44 Chamfer edges for a cleaner print and easier assembly
08:06 Final result: a printable clamp ring you can build other designs from
What you’ll learn
- How to project geometry (P) for faster, cleaner sketches
- How to build a parametric ring and iterate dimensions without remodeling
- How to place set screws using tangent planes and constrained sketches
- How to design a captive nut pocket for stronger, reusable fastening
- How to insert McMaster-Carr hardware (STEP) and assemble with joints
- How to circular-pattern features and finish with chamfers
Key dimensions used in the walkthrough (adjust to your hardware and printer)
- Slip fit clearance: 0.5 mm (starting point)
- Ring diameter adjustment: 75 mm changed to 78 to 79 mm (parametric iteration)
- Ring extrusion height: 10 mm
- M4 screw hole size shown: 4.5 mm
- Socket cap clearance: 7.5 mm
- Extra cut depth shown: -5.5 mm
- Captive nut pocket: 3.5 mm by 7.5 mm, cut depth 9 mm
- Example hardware: M4 socket head cap screw, 16 mm long, plus M4 square nut
- Pattern count: 3 set-screw stations around the ring
If you build your own version, share what socket standard you’re using and what clearances worked best for your printer (PLA, PETG, ABS). Subscribe for more Fusion workflows that combine clean parametric CAD with real hardware fit checks.
#autodeskfusion
#3dprinting
#CAD
#parametricdesign
#diylighting
youtube.com/channel/UCmGXH-jy0o2CuhqtpxbaQgA/join
In this Autodesk Fusion tutorial, you’ll design a robust fastener ring that lets a 3D printed part clamp securely onto an E26 lamp socket using M4 set screws and captive square nuts. You’ll work in hybrid mode, project reference geometry for clean sketches, build a parametric ring you can refine later, and pull in accurate hardware models from McMaster-Carr as STEP files to validate fit and assembly.
Chapters
00:00 Overview: attaching a 3D printed part to a cylindrical lamp socket
00:24 Why a set-screw clamp is better than relying on plastic threads
00:42 Insert components in Fusion (hybrid mode) and create the fastener ring component
00:59 Create an offset plane for a clean sketch setup
01:13 Project key rings and hide clutter to simplify the sketch
01:34 Sketch ring diameters and add clearance for sliding onto the socket
01:53 Extrude the ring (10 mm) and check placement against the socket
02:09 Create a tangent plane and sketch the set screw hole location
02:27 Size and constrain the hole (M4 clearance) so it’s properly centered
02:55 Add space for the socket cap (counterbore clearance)
03:23 Cut additional depth so the cap area seats cleanly
03:39 Create the captive square nut pocket for an M4 square nut
04:51 Insert an M4 socket head screw from McMaster-Carr (STEP) and joint it in place
05:36 Insert an M4 square nut from McMaster-Carr (STEP) and lock it with a rigid joint
06:39 Iterate with parametric edits to improve screw engagement and ring size
07:20 Circular pattern the set-screw features (3x) around the center axis
07:44 Chamfer edges for a cleaner print and easier assembly
08:06 Final result: a printable clamp ring you can build other designs from
What you’ll learn
- How to project geometry (P) for faster, cleaner sketches
- How to build a parametric ring and iterate dimensions without remodeling
- How to place set screws using tangent planes and constrained sketches
- How to design a captive nut pocket for stronger, reusable fastening
- How to insert McMaster-Carr hardware (STEP) and assemble with joints
- How to circular-pattern features and finish with chamfers
Key dimensions used in the walkthrough (adjust to your hardware and printer)
- Slip fit clearance: 0.5 mm (starting point)
- Ring diameter adjustment: 75 mm changed to 78 to 79 mm (parametric iteration)
- Ring extrusion height: 10 mm
- M4 screw hole size shown: 4.5 mm
- Socket cap clearance: 7.5 mm
- Extra cut depth shown: -5.5 mm
- Captive nut pocket: 3.5 mm by 7.5 mm, cut depth 9 mm
- Example hardware: M4 socket head cap screw, 16 mm long, plus M4 square nut
- Pattern count: 3 set-screw stations around the ring
If you build your own version, share what socket standard you’re using and what clearances worked best for your printer (PLA, PETG, ABS). Subscribe for more Fusion workflows that combine clean parametric CAD with real hardware fit checks.
#autodeskfusion
#3dprinting
#CAD
#parametricdesign
#diylighting
youtube.com/channel/UCmGXH-jy0o2CuhqtpxbaQgA/join










