Mr.D - Falling with style | Flaps with elevator compensation and slow, using ETHOS @MrD | Uploaded 1 year ago | Updated 6 minutes ago
🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC
In this video, we extend my earlier video on setting up flaps, flaperons, and spoilerons in ETHOS. This time we also add elevator compensation and use the slow up and slow down options to make the transition longer. As a little bonus, I also throw in full span ailerons at the end too.
Please note: In the video I show up elevator to compensate for down flaps. This is usually correct for regular flaps and flaperons. But, coming in fast, they can cause balooning, which would require down elevator. Also, down elevator would be used for crow braking; where both flaps go down and both ailerons go up. The best thing to donis start with low values, test a few mistakes high, and see what works best for your plane and approach speed.
Another note is that the values I'm using in the video for compensation are just for demo purposes. You should try with no compensation first. Then add compensation if it's needed, and gradually increase it.
✈️ Contents ✈️
00:00 Introduction
00:45 The setup used for the demo
01:15 Setting up the new model, with flaps
03:35 Checking out the mixer that has been set up
04:08 Assigning the input to the flaps
05:44 Looking at the Ail to Ele mix to see what is does
07:28 Setting up elevator compensation using my method
14:25 Adjusting the half flaps position
15:43 Adding slow up and slow down to the flaps and elevator compensation
17:06 Adjusting flap limits
18:35 A quick look at full span ailerons
21:41 Conclusion
Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.
✈️ In this video ✈️
🔗 Original ETHOS flaps video: youtu.be/zV-RaqU0Upg
⚙️ FrSky Tandem X20S transmitter: bit.ly/MrD_3x6n6JL
⚙️ FrSky SR10 Pro receiver: bit.ly/MrD_3DFQeKF
✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.
✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su
🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.
Thank you for your time, and don't forget to fly it like you stole it!
🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC
In this video, we extend my earlier video on setting up flaps, flaperons, and spoilerons in ETHOS. This time we also add elevator compensation and use the slow up and slow down options to make the transition longer. As a little bonus, I also throw in full span ailerons at the end too.
Please note: In the video I show up elevator to compensate for down flaps. This is usually correct for regular flaps and flaperons. But, coming in fast, they can cause balooning, which would require down elevator. Also, down elevator would be used for crow braking; where both flaps go down and both ailerons go up. The best thing to donis start with low values, test a few mistakes high, and see what works best for your plane and approach speed.
Another note is that the values I'm using in the video for compensation are just for demo purposes. You should try with no compensation first. Then add compensation if it's needed, and gradually increase it.
✈️ Contents ✈️
00:00 Introduction
00:45 The setup used for the demo
01:15 Setting up the new model, with flaps
03:35 Checking out the mixer that has been set up
04:08 Assigning the input to the flaps
05:44 Looking at the Ail to Ele mix to see what is does
07:28 Setting up elevator compensation using my method
14:25 Adjusting the half flaps position
15:43 Adding slow up and slow down to the flaps and elevator compensation
17:06 Adjusting flap limits
18:35 A quick look at full span ailerons
21:41 Conclusion
Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.
✈️ In this video ✈️
🔗 Original ETHOS flaps video: youtu.be/zV-RaqU0Upg
⚙️ FrSky Tandem X20S transmitter: bit.ly/MrD_3x6n6JL
⚙️ FrSky SR10 Pro receiver: bit.ly/MrD_3DFQeKF
✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.
✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su
🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.
Thank you for your time, and don't forget to fly it like you stole it!
