Uploaded April 2022 | Updated November 2026, 1 hour ago
Finally, a rag-chew version of FT-8!
The mode JS8 began as a derivative of the WSJT-X group of modes that was restructured to allow message passing using a form of the FT8 mode, modified by Jordan Sherer and was named JS8.
Initially, the s/w program was named FT8Call, and later renamed to JS8Call. In clarification, JS8 is the mode and JS8Call – for JS8 Directed Calling, is the Software program that uses the JS8 digital mode to provide weak signal messaging to Hams.
This program is experimental and still under development. Using open-source code, you can be part of the development and submit your changes to the JS8Call group for potential inclusion in future iterations of the software.
The purpose of the experiment is to test a digital mode with the potency of FT8, along with being messaging capable with a communications protocol for low power comms. It has no other purposes other than connecting hams, operating with low power systems, keyboard to keyboard.
Thus, the primary benefit to ham communications is being able to pass pre-defined messages and rag-chews by directed calling.
JS8 Frequency Chart:
160 M 1.842 MHz
80 M 3.578 MHz
40 M 7.078 MHz
30 M 10.130 MHz
20 M 14.078 MHz
17 M 18.104 MHz
15 M 21.078 MHz
12 M 24.922 MHz
10 M 28.078 MHz
6 M 50.318 MHz
Chapters:
00:17 Introduction
02:16 A brief History of JS8
04:38 JS8Call Download
07:11 FT-991A Menu and Function Settings
10:31 Computer Settings (Device Manager)
12:51 JS8Call Settings
18:03 JS8 HeartBeat demo
20:18 JS8 QSO Demo
27:04 End-Notes
Hope you enjoyed – don’t forget to like, share, comment, and subscribe.
73 de Tom, ND3N
Finally, a rag-chew version of FT-8!
The mode JS8 began as a derivative of the WSJT-X group of modes that was restructured to allow message passing using a form of the FT8 mode, modified by Jordan Sherer and was named JS8.
Initially, the s/w program was named FT8Call, and later renamed to JS8Call. In clarification, JS8 is the mode and JS8Call – for JS8 Directed Calling, is the Software program that uses the JS8 digital mode to provide weak signal messaging to Hams.
This program is experimental and still under development. Using open-source code, you can be part of the development and submit your changes to the JS8Call group for potential inclusion in future iterations of the software.
The purpose of the experiment is to test a digital mode with the potency of FT8, along with being messaging capable with a communications protocol for low power comms. It has no other purposes other than connecting hams, operating with low power systems, keyboard to keyboard.
Thus, the primary benefit to ham communications is being able to pass pre-defined messages and rag-chews by directed calling.
JS8 Frequency Chart:
160 M 1.842 MHz
80 M 3.578 MHz
40 M 7.078 MHz
30 M 10.130 MHz
20 M 14.078 MHz
17 M 18.104 MHz
15 M 21.078 MHz
12 M 24.922 MHz
10 M 28.078 MHz
6 M 50.318 MHz
Chapters:
00:17 Introduction
02:16 A brief History of JS8
04:38 JS8Call Download
07:11 FT-991A Menu and Function Settings
10:31 Computer Settings (Device Manager)
12:51 JS8Call Settings
18:03 JS8 HeartBeat demo
20:18 JS8 QSO Demo
27:04 End-Notes
Hope you enjoyed – don’t forget to like, share, comment, and subscribe.
73 de Tom, ND3N









![IC7300MK2 Digital Settings and Presets
This video takes a look at setting up the new ICOM IC-7300MK2 for digital modes. By the way, much of this video applies to the original IC-7300.
Well go through all of the rig settings and functions necessary for use with digital modes. Well also take a look at the preset Settings. Since this is a new rig on the market, none of the use your software packages include the mark 2, so Ill be showing you the work around to get your mark 2 working with digital software.
List of Settings:
Display Screen:
Mode = USB-D
Filter = FIL1
Bandwidth = 3.0 K
Main Settings:
SET/Function/Tuner:
a. [TUNER] Switch = Auto
b. PTT Start = ON
SET/CONNECTORS/USB AF/IF Output:
c. Output Select = AF
d. AF Output Level = 25-ish (Audio input – Speaker)
SET/CONNECTORS/MOD Input
e. USB MOD Level = 50 (Drive Level - Mic)
f. DATA MOD = USB
SET/CONNECTORS/CI-V
g. CI-V Baud Rate = (Your Choice) 19200
h. CI-V Address = 94h
SET/CONNECTORS/USB (B) Function = CI-V
Functions:
P.AMP/ATT = P.AMP1
AGC = FAST (Medium will work as well – experiment for your system)
NOTCH/NB/NR = OFF
IP+ = ON
VOX = OFF
1/ 4 = User Choice
MONI = ON
Preset 2 (Default Name “FT8” – My Name “Digi B6
** Note anything not used will be unchecked and not discussed in this list…
Preset Name: Name whatever you want
Mode: USB-D
Filter: FIL1
Filter BW: 3.0k
Filter Type (HF): Soft
USB Output Select: AF (Audio Freq)
USB AF Output Level = 25%-ish
USB MOD Level = 50% - ish
DATA MOD = USB
SSB-D TX Bandwidth = 300-2700
CI-V Baud Rate = Your choice, I prefer 19200 and avoid using Auto
CI-V Address = B6h
** Make sure you “Write” after changes
Preset 1 (Default Name “Normal” – My Name “Digi 94”
Same as above, except change Preset Name to Digi 94 (or whatever you want to call it. “Fred” and “Barney” work just as well as anything else…)
Also, change CI-V Address to 94h
Chapters:
01:24 Main Display
02:30 Main Settings
05:55 Functions
06:31 Multi-Knob Selections
07:28 Presets
13:57 Proof of Concept
Thanks for watching. Please remember to comment, like, and share this video. Also, please consider subscribing to this channel. I certainly appreciate it. Future videos will do a deeper dive into these digital modes .
73 de Tom, ND3N IC7300MK2 Digital Settings and Presets](https://i.ytimg.com/vi/QdcEAK1ZycU/mqdefault.jpg)
