3D Printed DND Spell Tracker! Chris Borge 2021-01-21 | A 3D printed stat tracker for playing DND! Parts: youtu.be/Ei0PX8uxiEUMusic:serpentsoundstudios.com/royalty-free-music/celtic-fantasyFollow my socials:twitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
They Said I Couldnt Fix It Chris Borge 2024-03-05 | Man turns garbage into more complicated garbage.Music:Blue Danube, youtube audio libraryFollow my socials:Instagram: borge_designtwitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
A Normal And Logical Vacuum Forming Video #3dprinting #diy #3dprint #howto Chris Borge 2024-02-23 | Music:Strad, minecraft soundtrackfull video: youtu.be/HfOymggDOeQ?si=-OUIPhRhYePgQ78S
Lets Get Organized! #organization #diy #3dprinting Chris Borge 2024-02-22 | Music:Wait, Minecraft soundtrackFiles (AHAHAHAHAHAHAHAH):printables.com/model/775633-small-file-holder
The Little Things Make A Big Difference! #diy #organization Chris Borge 2024-02-21 | Music: Strad, minecraft soundtrackFollow my socials:Instagram: borge_designtwitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
I Invented The Worlds First Macuum Former Chris Borge 2024-02-20 | This is one of the projects of all timeIn this video I turn a broken Mac Mini into a vacuum forming machine. Why did I do this? Im still not sure myself.MAKE THE WATCH:printables.com/model/773292-retro-watch-skinOr the mac-uum former (its not THAT bad)printables.com/model/773327-the-worlds-first-macuum-formerMusic:Follow my socials:Instagram: borge_designtwitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
How To Build A Camera Lucida Chris Borge 2023-12-27 | Time flies aye.Finally got around to making this, been busy finishing study.The much requested build guide for my camera lucida design. Apologies on the wait. Lucida 3D:printables.com/model/526409-lucida-3d-portable-camera-lucidaLucida basic:printables.com/model/695381-basic-camera-lucidaFollow my socials:Instagram: borge_designtwitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
I Printed A 200 Year Secret Tool; Camera Lucida Chris Borge 2023-07-13 | Camera Lucida, a tool invented in 1807 and the precursor to photography for capturing accurate images. In this video a print a new take on it and cover its history with the help of the contemporary expert on the topic, Professor Pablo Garcia.Thankyou to Pablo for helping me with the interview for this video. An experts voice goes miles and brought ideas that I never would have found on my own.Pablo's Neo Lucida:neolucida.comFiles:Lucida 3D: printables.com/model/526409-lucida-3dFelipe Sai, camera lucida:thingiverse.com/thing:4529152Build guide: Coming Soon (I need a day off)Affiliate links to equipment I use:Ortur Laser Master 3:https://s.zbanx.com/r/ZBJXsUyGmz46Use code DB105 for $105 offMusic:Minecraft soundtrack :)Follow my socials:Instagram: borge_designtwitter- twitter.com/borgey5 thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.Timestamps:0:00 intro1:28 What Is Camera Lucida5:07 My design7:20 Who Used Camera Lucida10:49 Testing My design13:22 How you can get a Camera Lucida14:08 outro14:24 the death of camera lucida
Organizing My Life With Lasers Chris Borge 2023-05-31 | Skadis is great, just wish it came in more sizes. But why wish when you can cut your own on a laser?Thankyou to Ortur for sponsoring me with the laser used in this video. If you are interested in picking one up for yourself you can do so using the following link (affiliate):https://s.zbanx.com/r/ZBJXsUyGmz46Use code DB105 for $105 offSkadis board maker:printables.com/model/206256-parametric-skadis-board-generatorParts:printables.com/model/495104-a-small-skadis-assortmentMusic:Scratch the itch- quincas MoreiTake it easy- bad snacksA Night Alone- Track TribeFollow my socials:Instagram: borge_designtwitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
How To Build Your Own Printed Multitool Chris Borge 2023-03-13 | The Long Awaited (?) build guide for the model 303 card tool. Usual style, lower effort than the normal videos just whatever makes the process the clearest. Music: MydNyte - Noir Et Blanc ViePart 1: youtu.be/sD0iNubrY_oFiles: printables.com/model/391307-model-303-wallet-multitoolBOM:7 M 1.6* glasses screws, between 4-4.5mm long, $4 AUDFlat head pin, up to 30mm long, $3 AUD2*4 mm lengths of spring 2mm in diameter, optional but recommended, $5 AUDReplacement pen for victorinox swiss card, $2 AUDReplacement tweezers for victorinox swiss card, $5 AUD“11 in 1 wallet multitool”, $5 AUD and upCraft blades like a #11 or similar, $2A key, LW4, $5OR SD card + adaptor Total: 28 AUD/ 18 USDThese are the cheapest prices I could find to buy but many come with far to many pieces. A google search will find all of these easily.Follow my socials:Instagram: borge_designtwitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
This Multitool Is 3D Printed Chris Borge 2023-02-06 | PARTS: printables.com/model/391307-model-303-wallet-multitoolI like wallet multitools. They are convenient for most of my day to day needs but nothing on the market quiet does everything I want. Ive made some (poorly) in the past, so come with today as I fix my past mistakes. Music:Wehrmut- godmodeSoft Knives- sefcholTempos Vari- Freedom Trail StudioFollow my socials:Instagram: borge_designtwitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
I Printed The Perfect Fume Extractor Chris Borge 2022-12-24 | happy holidaysFILES:KIRBY:printables.com/model/348385-kirby-40mm-fume-extractorMODEL 302:printables.com/model/348425-model-302-40mm-fume-extractorKirby sucks. So do fume extractors. You do the math.Music:Kirby squeak squad OSTFollow my socials:Instagram: borge_designtwitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
3D Printed Tapping Arm: Build Guide! Chris Borge 2022-12-09 | A build guide! BOM on the following sites.thingiverse.com/thing:5683329printables.com/model/334976-tapping-arm-and-addonsFollow my socials:Instagram: borge_designtwitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
I Printed This Tool To Break Less Taps Chris Borge 2022-12-05 | Long time no see (for real this time)ive been taking time to move into my new studio/ workshop in-between other work and making stuff. Ive been reflecting on how im not really satisfied with some of my old work and I want future projects to be actually useful tools not just experiments, so like with this im taking more time to test and use the tools before publishing.FIles:thingiverse.com/thing:5683329printables.com/model/334976-tapping-arm-and-addonsBOM on bothWILL UPLOAD TO PRINTABLES ECT IN THE MORNINGTapping jigs are commercially available but I was unhappy with what was out there so considering how simple in nature they were, I went to design my own. Music:Follow my socials:Instagram: borge_designtwitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
Organise Your Cables With This Filament Spool Organiser (Parametric!) Chris Borge 2022-02-01 | A parametric cable organise that is made using old fillament spool! get organised and use up some of those pesky spools!PARTS:Prusa (Use this one, you dont need to sign up and it supports me!)prusaprinters.org/prints/127028-parametric-filament-spool-cable-organiserThingiverse (if you must :/ )Music:Track 1- Night Run AwayTrack 2- Wolf MoonFollow my socials:Instagram: borge_designtwitter- twitter.com/borgey5Prusa:thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
Super Simple 3D Printed Plastic Bottle Cordage Maker | Tutorial + Uses Chris Borge 2022-01-13 | im baaack. tldr I drove through a desert and then built a workshop so haven't been making regular videos. many many coming soon now that its done.In this video I revisit my bottle cordage maker and completely overhaul it, as well as showing a bunch of use cases. Donations much appreciated :) paypal.me/cborge333PARTS:*downloading from PRUSA supports the channel through their prusameters program, so I would prefer if you download from there!*Prusa: prusaprinters.org/prints/118602-plastic-bottle-cordage-maker-v3Thingiverse: thingiverse.com/thing:5198280Music:Intro: The World's fair - godmodeMid: Six Seasons - Unicorn HeadsOutro: Hannon - Jeremy BlackFollow my socials:Instagram: borge_designtwitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs REFERENCES/ LINKS:Filament videos:1- youtu.be/qRcsYdBe2982- youtu.be/UHXBOzjKNXY3- youtu.be/Eecbdb0bQWQFishing with cordage: youtu.be/QraoLyg_BF0Grim workshop: grimworkshop.comRecycling plant tour: youtu.be/nUrBBBs7yzQChapters:0:00 intro0:35 comparison to v11:40 overview2:19 assembly3:38 how to use4:27 How to make cable wraps5:45 general uses6:31 making filament7:13 outdoors/ survival uses10:13 options to buy10:49 environmental considerations12:19 outroLike subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
3D Printed Die Filer Shreds Metal (part 1) Chris Borge 2021-09-17 | Donations much appreciated :) paypal.me/cborge333So I 3D a die filer. in this video I show what I've made so far and what I still have to do. I Teased this a while back but due to a certain vise and some issues with building it its taken longer than planned. I wanted to get this up today since im away all of next week and didnt want to put it off any more. Open source as usual, ill have the files up a bit later *this is still a WIP! This video is showing my progress so far, part two will be the final version which will go over the final design decisions ect. WOULD NOT RECOMMEND PRINTING YET! Files are just for anyone curious or who may be working on something similar.*FILES: thingiverse.com/thing:4968102Music:Intro: tiptoe out backMain: six seasons, unicorn heads(taken from youtube audio library) Follow my socials:Instagram: borge_designtwitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffReferences:Sheet metal process:youtube.com/watch?v=5CuJjSk4U38First recorded die:copper.org/education/history/60centuries/industrial_age/invention.html#:~:text=In%201769%20the%20first%2Dnamed,from%20sheets%20in%20bulk%20quantities.All american die filer document:http://wentztech.com/WebDisk/Metalworking/Die%20Filer/All%20American%20Filing%20Machine.pdfProgressive die example:en.wikipedia.org/wiki/Die_(manufacturing)#/media/File:ProgressiveDieToyota-strip-scrap.jpgWhat is EDM?:youtu.be/pBueWfzb7P0EDM diagram source:en.wikipedia.org/wiki/Electrical_discharge_machining#/media/File:Wire_erosion.pngOther die filer videos:youtube.com/watch?v=6lxJ3E_UjtYyoutube.com/watch?v=ZNwvjaIW-pUyoutu.be/efI1kdhtjOMTIMESTAMPS:0:00 intro1:56 background info4:04 why not buy one?4:32 project goals4:43 costs5:21 files it can use6:04 changing support plates6:20 adjust table tilt6:48 the fence7:34 file support arm7:50 motor specs8:25 print fails!!9:27 test 110:31 test 210:44 test 311:20 design issues12:21 outroMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
3D Printed Fractal Vise Build Guide Chris Borge 2021-08-21 | This is the build guide for my vise. its a longer video but I figure if your making one being to specific cant hurt. I hope this covers everything.Files: thingiverse.com/thing:4931700Source files: dropbox.com/sh/7bpgve4as4jl0lq/AAApnlVQ8KqblNU9pDvvBI38a?dl=0Music: Islabonita - An JoneFollow my socials:Instagram: borge_designtwitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Timestamps: 0:00 intro0:26 non printed hardware01:14 part printing orientation01:37 small jaws06:06 TPU jaw06:27 leadscrew filing7:00 begin assembly 18:33 outroLike subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
3D Printed Fractal vise V2: Overview + CNC router testing Chris Borge 2021-08-13 | The "long awaited" version 2 of my fractal vise! Now optimised for use not just show! In this video I show my new designs, upgrades, and test it in a variety of scenarios. I think it for sure it is a useful tool as the results in this video show. Build video up next so sit tight for that. In regards to the comments in the video, its something im trialling, obviously I cant fit all comments in, in this case I collected these a few weeks back so sorry if you made a similar suggestion and were not featured. Parts: thingiverse.com/thing:4931700Source files: dropbox.com/sh/7bpgve4as4jl0lq/AAApnlVQ8KqblNU9pDvvBI38a?dl=0Materials list: ~around 1.8M of 4.5mm/ 3/16th threaded rod3x m4 bolts at least 70mm long~30cm 1.5mm rod for jaw type Avery small elastic for jaw type ATPU for jaw type BAppropriate nuts washers ect. Music: 6 seasons: unicorn headsfully printed vise by ToMaTo Lab:youtube.com/watch?v=nqj4Pu4hsq80:00 intro0:19 thanks for last time0:55 comparison to v11:21 new jaws2:40 new body design4:39 testing 6:25 CNC testing8:54 upgrades10:30 final thoughts10:57 outroFollow my socials:twitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
3D Printed Fractal Vise (WIP!!!) Chris Borge 2021-06-30 | Parts:thingiverse.com/thing:4897556I see video, I want thing I make thing. I said it in the video but ill say it again, it works but is a WIP and I will probably change some things as I polish it in the future. I think what I have so far is a good proof of concept that these vises can be 3D printed effectively. Even this early version still holds things very well!Hand tool rescue:youtube.com/watch?v=QBeOgGt_oWUMusic:Ghost Dance by Kevin MacLeod is licensed under a Creative Commons Attribution 4.0 license. creativecommons.org/licenses/by/4.0Source: http://incompetech.com/music/royalty-free/index.html?isrc=USUAN1100573Artist: http://incompetech.comJust dance by:youtube.com/channel/UCTPI2hZYxoHtdGEpdFoaU5AFollow my socials:twitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
3D Printed Wood Lathe V4! Chris Borge 2021-05-31 | A slightly upgraded version of my wood lathe, with some fixes and new parts. Could be considered a "final" version of this design, its more polished than the previous versions.PARTS: thingiverse.com/thing:4874288Music:1- Just dance2- The worlds Fairfrom youtube audio library Follow my socials:twitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
Anycubic Photon 0 Print Not Starting Fix Chris Borge 2021-05-12 | So my photon and apparently some others as well like to randomly stop working for no apparent reason, in this video I update the firmware to fix the issue. Really cant reccomend this printer, it prints yes but it is an absolute pain to work with for reasons such as this one. Spend the extra hundred to get a photon S rather. Music: nope!Follow my socials:twitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
(1000 sub special) Workshop tour + channel updates Chris Borge 2021-04-01 | ahahhHEhahahaha April fools!!!!!!!! More actual content coming soon! I hope!!!Music:Follow my socials:twitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
Mini Chop Saw 3D Printed DRO Upgrade! Chris Borge 2021-02-14 | After buying a cheap Mini Chop Saw off of eBay, I saw some room for improvement. I may make some more mods in the future but this one, making a simple attachment for a cheap set of eBay callipers, was the most obvious for me. Requires no drilling or cutting of the saw or the callipers! Parts: thingiverse.com/thing:4761985Music: Marxist arrowFollow my socials:twitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
Dremel lathes; A Bad Idea? Chris Borge 2021-01-09 | Why I wont be releasing my Dremel lathe. tl;dr, a dremel has to high RPM, to low torque to be good for wood turning. I felt very unsafe using it. A more expert video: youtube.com/watch?v=8lq78dWdwH4Follow my socials:twitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
3D Printed Manual Mill- Build Video Chris Borge 2021-01-06 | Finally done with this. Parts:thingiverse.com/thing:4621593Main video: youtube.com/watch?v=f_YHH4x78OUParts list: docs.google.com/document/d/1tXt6cKK5RWPhWFaBYoYP7OQ9uzSXPP-uHx3xKvjvhr4/edit?usp=sharingMusic:Contact high, RKVCFollow my socials:twitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
3D Printed Wood Lathe- Build Guide Chris Borge 2021-01-02 | its here and it is what it isAny further questions feel free to askMusic:Polyphonic Congas - Unicorn HeadsThingiverse parts: thingiverse.com/thing:4678844Other parts:27cm 5/32nd rod, 2-3m4*20mm bolts, 2m4*15mm bolts, 8m3*20mm bolts, 4m2*20mm bolt, 13/16th threaded rod lengths, 13cm, 43/16th threaded rod length, 9cm, 13/16th ~50mm bolts, 43/16th nuts, 146mm rod, 30cm5mm rod, 9cm, 1er 11 collet chuck, 5mm mountsmall wood screws, 131.7mm thick aluminium plates, 30*30mm, 34* 10mm OD, 5mm ID bearings2* 10mm OD, 6mm ID bearingsFollow my socials:twitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
How Much Did I Spend On 3D Printing In 2020 (And Other 2020 stuff) Chris Borge 2020-12-31 | Music:Contact High - RKVCFollow my socials:twitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from Australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
Turning 100 Year Old Redgum (On a 3D Printed Lathe) Chris Borge 2020-12-28 | Another wood turning video woooo!!!Music:Marxist arrowFollow my socials:twitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
3D Printed Keychain Fire Kit Chris Borge 2020-12-26 | Music:I feel like partying right nowParts: thingiverse.com/thing:4697639https://www.ebay.com.au/itm/Outdoor-Survival-Camping-Tool-Magnesium-Flint-Scraper-Stone-Fire-Starter-Lighter/174302572893?hash=item28953e315d:g:AxgAAOSwPJxe1Ludhttps://www.ebay.com.au/itm/NEW-Aluminum-Pill-Box-Case-Bottle-Cache-Drug-Holder-Keychain-Container-Waterproo/143620575968?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649https://www.ebay.com.au/itm/5PCS-mini-Emergency-Flint-Fire-Starter-Rod-Lighter-Magnesium-camping-tool-kits/274444584733?hash=item3fe62c071d:g:u34AAOSwnF9Y6wjA&frcectupt=trueMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future. Follow my socials:twitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuff
Making Hammers On A 3D Printed Lathe (Christmas special 2020) Chris Borge 2020-12-25 | Music:Carol of the bellsHolly DazedWe Wish You a Merry Christmas (Instrumental Jazz) - E's Jammy JamsFollow my socials:twitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
Mill Build Video Update + General Channel Stuff Chris Borge 2020-12-20 | made at 3am lesgoTEMP PARTS VIDEO:youtu.be/7UfhFsHoo3APARTS LIST DOC (WIP): docs.google.com/document/d/1tXt6cKK5RWPhWFaBYoYP7OQ9uzSXPP-uHx3xKvjvhr4/edit?usp=sharingFollow my socials:twitter- twitter.com/borgey5My name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future. thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuff
3 Useful Tools For 3D Printing (That You May Not Have Thought Of!) Chris Borge 2020-12-14 | Music: Theme for a one handed pianist Parts: thingiverse.com/thing:4685375Hammer (shop around, there could be cheaper!): https://www.ebay.com.au/itm/Car-Safety-Hammer-Seat-Belt-Cutter-Window-Breaking-Emergency-Escape-Tool-W8/184565423459?_trkparms=aid%3D111001%26algo%3DREC.SEED%26ao%3D1%26asc%3D20160908105057%26meid%3Dd59aa645e14844c2a46c858d2bc8bd0b%26pid%3D100675%26rk%3D4%26rkt%3D15%26mehot%3Dnone%26sd%3D143739987330%26itm%3D184565423459%26pmt%3D1%26noa%3D1%26pg%3D2380057%26brand%3DUnbranded&_trksid=p2380057.c100675.m4236&_trkparms=pageci%3A6393d1d3-3e11-11eb-84b1-3a22e3916a12%7Cparentrq%3A61779ab91760ada186ec34a5fff7dca8%7Ciid%3A1Follow my socials:twitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
3D Printed Wood Lathe (V3) Chris Borge 2020-12-08 | Parts: thingiverse.com/thing:4678844Parts on cults: cults3d.com/en/3d-model/tool/wood-lathe-version-3Music:Flight of the BumblebeeOP_28Follow my socials:twitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
3D Printed Wood Lathe (Part 1) (WIP) Chris Borge 2020-11-16 | yes, I know that i nearly cut my hand off at the start. im working on it. Music: The sound of a dollar by DJ Williams PARTS: thingiverse.com/thing:4655283Follow my socials:twitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
3D Printed Milling Machine (Part 2) - Wood Lathe Addon Chris Borge 2020-11-06 | Another addon for the mill, this time adding wood lathe capabilities. Parts:thingiverse.com/thing:4644865Music:Marxist Arrow by Twin Musicom is licensed under a Creative Commons Attribution 4.0 license. creativecommons.org/licenses/by/4.0Artist: http://www.twinmusicom.orgFollow my socials:twitter- twitter.com/borgey5My name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future. thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuff
3D Printing Isnt Just For Making Toys and Trophies Chris Borge 2020-11-02 | A bit of a different video because it was made for a uni assignment and had to meet certain requirements but I thought eh may as well chuck it up here as well. Mill updates and more coming soon!Music:Theme for a one handed piano concerto by Sir CubworthFollow my socials:twitter- twitter.com/borgey5My name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future. thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuff
3D Printed Milling Machine (Part 1) Chris Borge 2020-10-12 | Music: no.9 Esthers WaltzPARTS: thingiverse.com/thing:4621593Follow my socials:twitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs Like subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
3D Printed Drill Press (Part 3) - Basic Drill Build Video Chris Borge 2020-09-18 | A more in depth build video. Ill be honest im not that happy with this but im not sure why so if you have any questions, feel free to ask. Also trying no music for most of this one, ive found it to be distracting in other videos so let me know how that goes. PARTS:Main parts:thingiverse.com/thing:4575661Table, tube holders:thingiverse.com/thing:4581998A video with more info: youtube.com/watch?v=6kxvxxR7nMMMusic: Strange Stuff by Matt HarrisFollow my socials:twitter- twitter.com/borgey5thingiverse- thingiverse.com/borgey/designs DETAILED PARTS LIST:All Brass/ alumium is from K&S precision metals, IK its a common thing in AU and US at least (its a US brand)The bolts kit I use: https://www.ebay.com.au/itm/500pcs-Screws-Set-Nuts-and-Bolts-Metric-M3-M4-M5-Hex-Socket-Head-Assortment-Kit/372791719657?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649The brass inserts I use:https://www.ebay.com.au/itm/Nut-Brass-Threaded-Equipment-Accessories-150pcs-Insert-For-3D-Printing/324009258812?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l26495/32nd brass rod: 2x90mm lengths, 2x 12cm+ lengths5mm steel rod: 90mmishAluminium plate: 100.6mm * 2x10mm od bearings, 5mm id 5x m3*16mm bolts3x m3*20mm bolts1xm4*20mm bolt2x springsLike subscribe all that stuffMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
3D Printed Drill Press (Part 2) - Table and Updates Chris Borge 2020-08-28 | Drill press part 2. PART 1: youtube.com/watch?v=Uh-EpV1XfyQMusic: ill update in the morning not on the PC with the name rn ahahahParts: thingiverse.com/thing:4581998My name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
3D Printed Drill Press (Part 1) Chris Borge 2020-08-21 | A 3D printed drill press ive been working on recently, part 1. Still a WIPDownload (STILL A WIP BUT HEY ITS HERE ANYWAYS): thingiverse.com/thing:4575661Intro music: Sneaky Bass Latina from youtube audio libraryMusic 2:Op 028 [Free Stock Music | Jazz | Instrumental] by natuch speaker: https://soundcloud.com/natuch_speaker...Attribution-ShareAlike 3.0 Unported (CC BY-SA 3.0)https://creativecommons.org/licenses/...Music provided by Free Vibes: goo.gl/NkGhTgMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
Random Ramble #2 - Watchmakers Lathes Show and Tell Chris Borge 2020-08-15 | whats up. No video this week because my weekly project has been a bit bigger than usual so look out for that in the next few days. anyways for this weeks casual video, I show off and talk about my watch makers/ jewellers lathes, 2 beautiful pieces of machinery that I acquired some years ago and hope to show off more in future videos.My name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
Random Ramble #1 - My Everyday Carry (August 2020). Chris Borge 2020-08-08 | In an effort to appease the algorithm and just because I was bored, I am planning an additional video per week. Unscripted and casual in style ill talk about gear or just random stuff that I feel like talking about. This weeks episode I talk about my current every day carry.My name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
Upgrading a Cheap Multi-tool with 3D Printing Chris Borge 2020-08-06 | So recently ive started doing something I never thought id do: Using one of those rubbish $2 card multitools. But I saw room for improvement, which is what this video is about. DOWNLOADSRegular:thingiverse.com/thing:4562778Cyberpunk:Music:1- I feel like partying right now2- strange stuff by Matt HarrisMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
3 Easy Bottle Cordage Makers (No 3D Printing) Chris Borge 2020-07-27 | Whats up everyoneAs a follow up to my last video, here are 3 more bottle cordage makers, this time using 0 3D printing.These things are cheap and easy to make and all function effectivly even if I didnt show if in the video (Filming myself is a pain, Im working on getting a better setup that allows me to reposition my lights better for future videos)Music is valley of spies by The Whole OtherMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
3D Printed Plastic Bottle Cordage Tool (Detailed Assembly Guide) Chris Borge 2020-07-19 | A longer, unscripted but also much more detailed assembly guide for the rope maker. VIDEO 1: youtube.com/watch?v=x8AFc1IqZ1IDOWNLOAD: thingiverse.com/thing:4545918My name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
Make Rope from Plastic Bottles with this Tiny Tool Chris Borge 2020-07-18 | Hey guys, whats up. This is my take on plastic bottle cord makers. This "hack" has been around for a while and the design here is for a simple, compact and easy to use version that is practical to be added to any survival kit or pack. It produces strong cordage that has many applications. It could also be used for craft applications.DOWNLOAD HERE: thingiverse.com/thing:4545918MUSIC: Reverie by Quincas MoreiraSCREW DRIVER BIT EXAMPLE: https://www.ebay.com.au/itm/Portable-8-In-1-Precision-Screwdriver-Bit-Set-Pen-Style-Repair-Kit-Tool/184024520341?hash=item2ad8b75695:m:m2Se8ruy0XuEsEHJ8ljPPnQMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
An Informal Tour of my Aquaponics Setup (Duck Reveal?!?!) Chris Borge 2020-07-15 | hello there. This video is a tour of a "aquaponics" setup that I built to keep my duck pond cleaner for longer. while simple and cheap it has helped greatly with the smell and we need to change the water much less.My name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
How to make a TINY LED Torch Chris Borge 2020-07-10 | Hey guys, long time no see. this video I show off my latest creation, a tiny torch intended for altoids tin survival kits.link to download: thingiverse.com/thing:4537464Music is Sweet Release by Dan LebowitzMy name is Chris, I am a 3D printing hobbyist from australia. I dont really specialise in anything specific, but 3D printed tools and tabletop accessories are some things youll probably seen quiet often. I do all my 3d printing on a Ender 3, which I highly recommend as a budget printer. Currently I only run 1 printer but I hope to expand that in the future. Recently acquired a photon 0 to do resin printing with. I like to share all my 3D printing ideas for free although I do plan to sell stuff in the future. Most of my projects will be mostly 3D printed with a few non printed components included, these can often be found on ebay. I actually use the cheapest filament I can get for all my projects, again I hope to change this in the future.
