Uploaded December 2021 | Updated November 2026, 3 hours ago
Reliable Property Data required for MS Design, Licensing, and Operation:
- Predicting molten salt behavior during normal and transient conditions requires knowledge of property values over a range of temperatures and salt compositions, including contaminants and accumulating fission products
- Licensing a reactor requires quality data collected using standardized methods with known precision and accuracy
- Available data are not sufficient or of suitable quality as most developers are considering salt mixtures other than LiF-BeF2-UF, for which reliable property values must be measured
Objectives of the MS Campaign Molten Salt Property Measurements:
Generate high-quality measurements of property values of fuel-bearing molten salts to assist developers in designing, licensing and operating MSRs. Identify quality-affecting aspects of property measurement techniques, sensitivities, and measurement controls to achieve NQA-1 data quality. Assess the precision of measurements. Distinguish effects of uncertainty in salt composition and in the measurement. Determine property values of reference salts that can be used to compare methods and determine within-lab repeatability, lab-to-lab reproducibility, and bias in measurements. Develop consensus standard practices issued through ASTM-International. Identify and generate database for an approved reference material salt (ARM-salt). Round Robin effort is supporting these tasks. Measure fuel-bearing systems using consensus standard practices controlled at the highest quality level. Data will be populated into the Molten Salt Thermal Properties Database (MSTDB) for developers to access.
Required Thermochemical and Thermophysical Properties:
- Liquids/solidus temperatures
- Salt boiling temperatures
- Vapor pressure
- Solubility of FPs and impurities
- Heat capacity
- Density
- Volume expansion coefficients
- Surface tension
- Viscosity
- Thermal conductivity/diffusivity
- Emissivity
Salts being Measured:
- Gaps in the MSTDB are being targeted by measurements of uranium- and plutonium- bearing fuel salts.
- Reference Salts - FLiNaK, FLiBe, and NaCI-KCI.
Confirming composition, impurity content and the impact of both on property values.
Optimizing measurement methods.
Quantifying data quality.
- Round Robin - National labs and Universities are measuring aliquots of the same batch of FLiNaK, and NaCI-KCI to quantify reproducibility of several methods.
Summary:
- MS Campaign Molten Salt Property Measurements
- Generating high quality measurements of property values of fuel-bearing molten salts to assist developers in designing, licensing and operating MSRs
- Identifying quality-affecting aspects of property measurement techniques, sensitivities, and measurement controls to achieve NQA-1 data quality
- Determining property values of reference salts that can be used to compare methods and determine within-lab repeatability, lab-to-lab reproducibility, and bias in measurements
- Developing consensus standard practices issued through ASTM-International
msrworkshop.ornl.gov/msr2021
ORNL MSRW 2021 YouTube Playlist:
youtube.com/watch?v=lm0EhN-CxkI&list=PLuGiwaUJYEZf1HYXPSGr58ieHNMCjXJxF
ThoriumRemix.com Thorium & MSR & Nuclear assets used in Thorium Remix project.
Reliable Property Data required for MS Design, Licensing, and Operation:
- Predicting molten salt behavior during normal and transient conditions requires knowledge of property values over a range of temperatures and salt compositions, including contaminants and accumulating fission products
- Licensing a reactor requires quality data collected using standardized methods with known precision and accuracy
- Available data are not sufficient or of suitable quality as most developers are considering salt mixtures other than LiF-BeF2-UF, for which reliable property values must be measured
Objectives of the MS Campaign Molten Salt Property Measurements:
Generate high-quality measurements of property values of fuel-bearing molten salts to assist developers in designing, licensing and operating MSRs. Identify quality-affecting aspects of property measurement techniques, sensitivities, and measurement controls to achieve NQA-1 data quality. Assess the precision of measurements. Distinguish effects of uncertainty in salt composition and in the measurement. Determine property values of reference salts that can be used to compare methods and determine within-lab repeatability, lab-to-lab reproducibility, and bias in measurements. Develop consensus standard practices issued through ASTM-International. Identify and generate database for an approved reference material salt (ARM-salt). Round Robin effort is supporting these tasks. Measure fuel-bearing systems using consensus standard practices controlled at the highest quality level. Data will be populated into the Molten Salt Thermal Properties Database (MSTDB) for developers to access.
Required Thermochemical and Thermophysical Properties:
- Liquids/solidus temperatures
- Salt boiling temperatures
- Vapor pressure
- Solubility of FPs and impurities
- Heat capacity
- Density
- Volume expansion coefficients
- Surface tension
- Viscosity
- Thermal conductivity/diffusivity
- Emissivity
Salts being Measured:
- Gaps in the MSTDB are being targeted by measurements of uranium- and plutonium- bearing fuel salts.
- Reference Salts - FLiNaK, FLiBe, and NaCI-KCI.
Confirming composition, impurity content and the impact of both on property values.
Optimizing measurement methods.
Quantifying data quality.
- Round Robin - National labs and Universities are measuring aliquots of the same batch of FLiNaK, and NaCI-KCI to quantify reproducibility of several methods.
Summary:
- MS Campaign Molten Salt Property Measurements
- Generating high quality measurements of property values of fuel-bearing molten salts to assist developers in designing, licensing and operating MSRs
- Identifying quality-affecting aspects of property measurement techniques, sensitivities, and measurement controls to achieve NQA-1 data quality
- Determining property values of reference salts that can be used to compare methods and determine within-lab repeatability, lab-to-lab reproducibility, and bias in measurements
- Developing consensus standard practices issued through ASTM-International
msrworkshop.ornl.gov/msr2021
ORNL MSRW 2021 YouTube Playlist:
youtube.com/watch?v=lm0EhN-CxkI&list=PLuGiwaUJYEZf1HYXPSGr58ieHNMCjXJxF
ThoriumRemix.com Thorium & MSR & Nuclear assets used in Thorium Remix project.










![Yorktown Clean Energy Center - Dr. Ganapati Myneni @ TEAC10
Dr. Ganapati Myneni, Director, VT-India Nuclear Energy Partnership, BSCE Systems, Inc.
Yorktown, Virginia, USA.
Specifications of the one way coupled sub-critical micro-reactors...
CW Electron Linac:
- Energy 10 -15 MeV
- Current 1 to 3 A
- Frequency 915 MHz
- Thermionic gun
- Operating temperature 4.25 K
- Forged ingot Nb cavity with Nb3Sn inner surface
Sub-critical Core:
- Molten salt burner/breeder
- Breed and burn in equilibrium
- Thorium in the central breeding zone
- Natural or slightly enriched uranium in the outer zone
Applications:
- High temperature heat sources
- Medical isotope generators in parallel
- Water desalination plants
- Back up to renewable energy sources close to cities and townships
Delivered at TEAC10, Thorium Energy Alliance Conference #10 on Oct 1st, 2019 [2019-10-01]. http://thoriumenergyalliance.com/
http://ThoriumRemix.com/ Thorium & MSR & Nuclear assets used in Thorium Remix project. Yorktown Clean Energy Center - Dr. Ganapati Myneni @ TEAC10](https://i.ytimg.com/vi/TgnnRmMt6Ts/mqdefault.jpg)