NeedItMakeIt | Ep.1 - These high speed 3D printer ducts produced some shocking results! @NeedItMakeIt | Uploaded October 2024 | Updated October 2024, 13 hours ago.
It has begun and I decided to make the tests even harder than before!
Help support this channel! patreon.com/Needitmakeit
It took a bit longer to get setup than expected, I thought I was going to be able to use the spools of Bambu filament that I bought just for these tests, but it turns out that I needed HF filament for this printer. I bought the grey Creality HF instead which I've used before, but never on this printer, so it took a bit to get it dialed in.
We're running the Cliffhanger, the Bridge Burst The Shuriken and of course the one and the only Benchy (Standard Version). As we get deeper into the competition we'll be able to run more tests as we narrow down the top performers to a smaller group. Ideally we'll do smoke testing, CFD simulations and we'll also use the Thermal camera to really see what's happening.
Overhung & Bridge_Burst (NIMI) - makerworld.com/en/models/668332#profileId-595924
Overhang Test Shuriken (By Rocksalt) - thingiverse.com/thing:6315375
Benchy (By CreativeTools) - thingiverse.com/thing:763622
I hope you enjoy the start to this competition and look out for more next week!
If you want to know all of the details of each test in Orca, the link to the .orca_printer file is below:
drive.google.com/file/d/1VUcD_16jln0aO8fc9BtL45VUrphb0VD7/view?usp=sharing
Thank you for helping to make this channel a success! Affiliate links:
**QIDI PLUS4** - qidi3d.com/products/plus4-3d-printer?sca_ref=5735403.eknTRISP1e
Early Bird - A choice of either a Tungsten Carbide Bimetal Nozzle or a Bimetal Hot End (Shipping begins in 2 months for these)
Possible Coupon - 30DAYSGIFT
Possible Coupon - HIGH5
QIDI Q1 Pro - qidi3d.com/products/q1-pro?sca_ref=5735403.eknTRISP1e
Thermal Master P2 - shrsl.com/4o6j1
Bambu X1C - shrsl.com/4j1gz
Bambu Filament Shown in Videos - shrsl.com/4ks0j
Creality HF PLA Filament - shrsl.com/4p9ag
Panda Jet For Bambu P1 and X1 Series (Tested and proven to work well) - shrsl.com/4jhht
Creality PI (Single) - amzn.to/3Xo3jUC
Creality PI (Double) - amzn.to/3XdQ4pj
Rode Mic - amzn.to/3vcMKAr - amzn.to/3NBFvZe
#qidi
#plus4
#ductshowdown
It has begun and I decided to make the tests even harder than before!
Help support this channel! patreon.com/Needitmakeit
It took a bit longer to get setup than expected, I thought I was going to be able to use the spools of Bambu filament that I bought just for these tests, but it turns out that I needed HF filament for this printer. I bought the grey Creality HF instead which I've used before, but never on this printer, so it took a bit to get it dialed in.
We're running the Cliffhanger, the Bridge Burst The Shuriken and of course the one and the only Benchy (Standard Version). As we get deeper into the competition we'll be able to run more tests as we narrow down the top performers to a smaller group. Ideally we'll do smoke testing, CFD simulations and we'll also use the Thermal camera to really see what's happening.
Overhung & Bridge_Burst (NIMI) - makerworld.com/en/models/668332#profileId-595924
Overhang Test Shuriken (By Rocksalt) - thingiverse.com/thing:6315375
Benchy (By CreativeTools) - thingiverse.com/thing:763622
I hope you enjoy the start to this competition and look out for more next week!
If you want to know all of the details of each test in Orca, the link to the .orca_printer file is below:
drive.google.com/file/d/1VUcD_16jln0aO8fc9BtL45VUrphb0VD7/view?usp=sharing
Thank you for helping to make this channel a success! Affiliate links:
**QIDI PLUS4** - qidi3d.com/products/plus4-3d-printer?sca_ref=5735403.eknTRISP1e
Early Bird - A choice of either a Tungsten Carbide Bimetal Nozzle or a Bimetal Hot End (Shipping begins in 2 months for these)
Possible Coupon - 30DAYSGIFT
Possible Coupon - HIGH5
QIDI Q1 Pro - qidi3d.com/products/q1-pro?sca_ref=5735403.eknTRISP1e
Thermal Master P2 - shrsl.com/4o6j1
Bambu X1C - shrsl.com/4j1gz
Bambu Filament Shown in Videos - shrsl.com/4ks0j
Creality HF PLA Filament - shrsl.com/4p9ag
Panda Jet For Bambu P1 and X1 Series (Tested and proven to work well) - shrsl.com/4jhht
Creality PI (Single) - amzn.to/3Xo3jUC
Creality PI (Double) - amzn.to/3XdQ4pj
Rode Mic - amzn.to/3vcMKAr - amzn.to/3NBFvZe
#qidi
#plus4
#ductshowdown