Uploaded October 2026 | Updated November 2026, 1 day ago
Electrical Principles playlist:
youtube.com/watch?v=k6thiyNzjpQ&list=PLEvyI-PjnnzI
A voltage divider is a simple circuit that uses resistors (or other components) to reduce an input voltage to a desired output voltage. It works by dividing the input voltage according to the ratio of the resistor values. Voltage dividers are commonly used in electronic circuits to provide suitable voltage levels for components such as sensors and microcontrollers.
Voltage dividers are one of the most basic and widely used building blocks in circuit design. They are often found in amplifier circuits and microcontroller input stages, where they help adjust signal levels for measurement, processing, and analog control.
Voltage Divider Rule
The Voltage Divider Rule is used to calculate the voltage across a resistor in a series circuit without calculating the current first.
Key points to remember
The rule applies to resistors connected in series.
A larger resistance gets a larger share of the supply voltage.
The sum of the voltage drops equals the supply voltage.
If a load is connected across one resistor, account for the load resistance because it changes the effective resistance.
Easy way to remember: Multiply the total voltage by the resistor you want, then divide by the total resistance.
Limitations
Inefficiency: They continuously waste current as heat through the resistors.
Load sensitivity: Connecting a load device with a low resistance in parallel to R2 will alter the total resistance and pull down the expected output voltage.
Consider two resistors connected across a 50 V supply, as shown. To demonstrate the potential divider effect, we will first calculate the circuit current and then determine the potential differences across the two resistors by applying Ohm’s law.
A current divider is a parallel circuit in which the source current splits between two or more parallel paths, called branches. The current flowing through each branch depends on the resistance of that branch.
As explained in our Resistors in Parallel, a parallel circuit has components connected across the same two nodes. This creates multiple paths through which current can flow. Although the voltage across each branch is the same, the current through each component can be different.
The key characteristic of a parallel circuit is that the voltage is the same across every branch, but the current can vary from branch to branch.
The total source current is equal to the sum of the currents flowing through all the branches.
Consider two resistors connected in parallel across a 48 V source, as shown. Using the potential difference method, we can calculate the current through each resistor as follows:
Applying the Formula to More Than Two Branches
When a circuit has three or more parallel branches, the current divider formula can help simplify the calculations. Let’s look at an example.
Consider a circuit with three resistors connected in parallel:
𝑅_1=10Ω,𝑅_2=20Ω,𝑅_3=30Ω,
Total current 𝐼_𝑇=12𝐴,
Find the current through 𝑅_2.
Step 1: Calculate the reciprocal of all resistances.
Step 2: Sum the reciprocals.
Step 3: Find the current through R2 using the formula
Electrical Principles playlist:
youtube.com/watch?v=k6thiyNzjpQ&list=PLEvyI-PjnnzI
A voltage divider is a simple circuit that uses resistors (or other components) to reduce an input voltage to a desired output voltage. It works by dividing the input voltage according to the ratio of the resistor values. Voltage dividers are commonly used in electronic circuits to provide suitable voltage levels for components such as sensors and microcontrollers.
Voltage dividers are one of the most basic and widely used building blocks in circuit design. They are often found in amplifier circuits and microcontroller input stages, where they help adjust signal levels for measurement, processing, and analog control.
Voltage Divider Rule
The Voltage Divider Rule is used to calculate the voltage across a resistor in a series circuit without calculating the current first.
Key points to remember
The rule applies to resistors connected in series.
A larger resistance gets a larger share of the supply voltage.
The sum of the voltage drops equals the supply voltage.
If a load is connected across one resistor, account for the load resistance because it changes the effective resistance.
Easy way to remember: Multiply the total voltage by the resistor you want, then divide by the total resistance.
Limitations
Inefficiency: They continuously waste current as heat through the resistors.
Load sensitivity: Connecting a load device with a low resistance in parallel to R2 will alter the total resistance and pull down the expected output voltage.
Consider two resistors connected across a 50 V supply, as shown. To demonstrate the potential divider effect, we will first calculate the circuit current and then determine the potential differences across the two resistors by applying Ohm’s law.
A current divider is a parallel circuit in which the source current splits between two or more parallel paths, called branches. The current flowing through each branch depends on the resistance of that branch.
As explained in our Resistors in Parallel, a parallel circuit has components connected across the same two nodes. This creates multiple paths through which current can flow. Although the voltage across each branch is the same, the current through each component can be different.
The key characteristic of a parallel circuit is that the voltage is the same across every branch, but the current can vary from branch to branch.
The total source current is equal to the sum of the currents flowing through all the branches.
Consider two resistors connected in parallel across a 48 V source, as shown. Using the potential difference method, we can calculate the current through each resistor as follows:
Applying the Formula to More Than Two Branches
When a circuit has three or more parallel branches, the current divider formula can help simplify the calculations. Let’s look at an example.
Consider a circuit with three resistors connected in parallel:
𝑅_1=10Ω,𝑅_2=20Ω,𝑅_3=30Ω,
Total current 𝐼_𝑇=12𝐴,
Find the current through 𝑅_2.
Step 1: Calculate the reciprocal of all resistances.
Step 2: Sum the reciprocals.
Step 3: Find the current through R2 using the formula










