Miele TwinDos DIY refillable detergent & fabric softener canisters (1/2) Ævar Arnfjörð Bjarmason 2020-03-25 | This video shows how to make refillable Miele TwinDos canisters for the detergent & fabric softener slots.Tools used:- Sewing needle & thread- Scissors- Power drill & 12mm drillbit (or another way to make a 12mm hole in plastic)- Carpenter's knife (or another way to smooth out the drilled hole)At around 4m40s in the video I screwed up and drilled through the bottom of the canister, which would have caused it to leak. That was easily fixed with some plastic glue & duct tape.Note that the cap added to the canister is only semi-watertight, I'm careful not to turn them upside down or stand them on their sides. It holds, but I don't really trust it. It's not a problem because there's no reason to ever orient them differently.It's VERY IMPORTANT when refilling the canisters not to overfill them. They're inserted at an incline into the machine, and the vent hole is in the front, therefore having too much detergent or fabric softener will block the vent hole, and the machine will only be able to suck out a little bit before negative pressure in the canister blocks any further extraction of the soap. See the last 30 seconds or so for the approximate fill limit (the label was custom added with a labeling machine I have).See youtu.be/FiZFQDTRuXU for the results.
Trauma helicopter landing in in West, September 29, 2025 Ævar Arnfjörð Bjarmason 2025-09-29 | See "Man (86) in scootmobiel gewond bij ongeluk met tram in West" on AT5 for the incident.
Miele TKR850 WP dryer: Activate service mode, rinse evaporator, run water pump Ævar Arnfjörð Bjarmason 2025-06-03 | ...
BMW CIC: DIY sled from a 2.5 HD for a cheap IDE to CF adapter, replacing the OEM HD (E60 etc.) Ævar Arnfjörð Bjarmason 2025-03-29 | The Toshiba HD for the BMW CIC (Car Infotainment computer) has a finite lifetime, so it's good preventative maintenance to replace it.The CIC runs many essential features in the car (more than just maps and music), if the HD fails and you don't have an image of it, you'll need a new CIC, and to have it coded to the car.I discuss:- How to make a DIY sled for the cheap IDE to CF adapter (one with a 2.5" sled is a hassle to get where I'm at)- Why not use an mSATA (or IDE to SATA etc.) adapter, the CIC OS doesn't support TRIM.One thing I left out here is a potentially much easier method: Use pliers to carefully insert the bare adapter itself (good to do this initially for testing). It will hang in place like that without support, at least when the car is stationary.Then use the OEM sled bracket along with something like styrofoam cut to size to wedge the IDE to CF adapter in place.The e90post I mention is at e90post.com/forums/showthread.php?p=31954089#post31954089I'm linking to my own chain of follow-up comments there instead of the top level, it's 15 pages, and since it was posted years ago a lot of the information has become stale.
Neonate N65 baby monitor broken vibration motor [description for details] Ævar Arnfjörð Bjarmason 2025-03-11 | Our Neonate N65 baby monitor bought in May 2023 stopped vibrating (can't remember exactly when, but around the 1.5 year mark).UPDATE: They sent me a new parent unit after sharing this video. Very happy with Neonate customer support END UPDATE I made this video to share with Neonate support, who said it was under warranty in principle (might be void now, but couldn't resist opening it).They use a 8mm by 3mm vibration motor. As the video shows the monitor alternates between giving it 0V and 2.33V DC (or thereabout).The nominally 3.7V battery puts out 4.11V (4.10V for the child monitor battery). Some of the motors I found (e.g. "5PCS Mini 8mm*3mm Vibration Motor DC 3V-5V 4.2V Button Type [...] Coin Flat Vibrator https://a.aliexpress.com/_EzQ4j68) are rated 3-5V, which would make more sense for the battery voltage.Without knowing what specific motor it is, and not wanting to screw around with the motherboard, I don't know if the issue is that it's not getting sufficient voltage, or that the board steps it down to around 2.33V, but the motor is just broken or worn out).Just for context, I didn't assume it would be under warranty, but contacted support to see if they'd be willing to either sell me a new motherboard or vibration motor, depending on whether the motor was replaceable (I hadn't opened it up at that time).
Uh ... ohhhh - our toddlers live commentary on Amsterdam road rage Ævar Arnfjörð Bjarmason 2025-01-31 | ...
BMW DIY howto: hardwiring using existing empty fuse slots (fuse tap alternative); E60, E61, E90, E91 Ævar Arnfjörð Bjarmason 2025-01-23 | I found and ordered the crimp connectors required for adding new fuse slots. On this and some comnemporar models that's 61138377734 "Double leaf spring contact 4,0-6,0 MM²(AG)".Some told me to just use a fuse tap, which honestly is probably better in every way, except for that irrational part of your brain that just wants an install like this to be "clean". If you're one of those people, then this how-to is for you.Still, this was much easier than I suspected. Those crimp connectors were €1.40 a piece from my local supplier.You don't even need to remove the glove box as I've done here, at least on the E6x you could just pop off the inner footwell trim and slide a new connector into the back. I have it off because it makes this much more ergonomic, especially for routing the lines themselves.Of course for a fuse tap that's even easier, as you only need to plug something into the front.One thing not mentioned here is that if you're doing this on a model like the E6x for e.g. wiring a dashcam you need to take other precautions to ensure you don't run your battery out, as anything wired into the front fuse box (and this isn't the same on E9x and various other models) *will* run down the battery to 0% unless switched in some other way.In my case I'm using this in combination with the hardwire kit for my dashcam (a VIOFO A129 Pro Duo). The camera itself has a "parking" setting with a timeout.It can detect that the car is "parked" because the hardwire kit comes with both a live "battery" line (which I'm hardwiring here), and a "parking detection" line. The latter you wire into some line that's switched already, I spliced it into one of the power lines going to the mirror. It also has a hardware voltage cutoff setting, which I've set to the right voltage after some experimenting.
Flushing out 15 years of power steering grime in 5 seconds (2009 BMW E61 w/N53, CHF 11s fluid) Ævar Arnfjörð Bjarmason 2024-10-06 | ...
Removing the BMW E60/E61s AT-auxiliary (xdrive transfer case) drain plug Ævar Arnfjörð Bjarmason 2024-03-11 | ...
Removing the BMW E60/E61s AT-auxiliary (xdrive transfer case) drain plug (long) Ævar Arnfjörð Bjarmason 2024-03-11 | I got it loose at the very last frame, and did the oil change. DIY's don't always take the time you expect.In this case the 14mm wrench I brought was bending, the longer adjustable wrench I brought didn't fit in the confined space. Ended up spending 30 minutes screwing around instead of 5 minutes to fetch another tool.
BMW E60/E61 cooling water expansion tank (#17137555234) repair with JB-weld. Passes a pressure test! Ævar Arnfjörð Bjarmason 2024-03-01 | ...
Schrader valve adapter for cooling system pressure test cap + Makita DMP180 cordless inflator Ævar Arnfjörð Bjarmason 2024-03-01 | ...
Bleeding the cooling system on a BMW E60/E61 with N52/N53/N54 engines Ævar Arnfjörð Bjarmason 2024-03-01 | ...
BMW E61s N53 with new belt, tensioner and idler. Needs a new vibration damper? Ævar Arnfjörð Bjarmason 2024-02-25 | ...
A BMW E61 with an N53 engine failing a cooling system pressure test Ævar Arnfjörð Bjarmason 2024-02-22 | ...
BMW E61 extra storage in spare tire well with an IKEA hack Ævar Arnfjörð Bjarmason 2024-01-25 | The IKEA cutlery holder: ikea.com/nl/en/p/ordning-cutlery-stand-stainless-steel-30011832The prerequisite is to have moved the trunk modules out of the way, which is a good idea in any case due to potential water intrusion.
Replacing a BMW N53 engines plasticMickey mouse flange with an aluminum aftermarket part Ævar Arnfjörð Bjarmason 2024-01-12 | I couldn't get the replacement on without breaking the O-ring at first, but like the video shows the solution is to lubricate it with the coolant, then it'll pop on without much difficulty.The replacement flange is a replacement for buying OEN 11537541992 and 11537544638 from BWW (which includes the hose going all the way to the thermostat).These instructions are also applicable with little or no modifications to the N20, N52, N54 and N55 engines in addition to the N53 here.
Makita DIY crappy transfer pump using old automotive windshield washer pump Ævar Arnfjörð Bjarmason 2024-01-10 | Stuff I used:* "External Battery Adapter Converter for MT Makita 14V/18V": https://a.aliexpress.com/_EGOIglP* "Cable Connector Set", for connecting the battery adapter to the pump (soldered on): https://a.aliexpress.com/_EwBpoFT* "Universal 2m Windshield Washer Nozzle Hose Tube Pipe": ttps://a.aliexpress.com/_Ezzb44H* Washer pump, most will do, mine's similar to: amazon.com/21323-232316B-Windshield-67128362154-67128377612-TAMKKEN/dp/B07XL6LHB5
Miele TwinDos DIY refillable detergent & fabric softener canisters (2/2) Ævar Arnfjörð Bjarmason 2020-03-25 | See youtube.com/watch?v=DTioY-SWE3Q
Mayrhofen Harakiri run Ævar Arnfjörð Bjarmason 2020-03-04 | My first time on this run, taken during the middle of the day when it's all carved up. Almost fell near the end blasting through some moguls.
Screwing around on Volkl Mantra 102s on Sierra Nevadas Trucha run Ævar Arnfjörð Bjarmason 2020-02-21 | ...
Bicycle accident in when the IJtunnel in Amsterdam was open to cyclists on May 29th, 2019 Ævar Arnfjörð Bjarmason 2019-05-28 | Was on the fence about uploading this, but since you can't see who it was or otherwise identify them I figured it was OK, and cycling the tunnel & what happened today has historical value...One one hand I wish a tunnel like this was open to bicycle traffic all the time, on the other hand it's clear from today that Dutch cyclists & their bikes are by-and-large not prepared to handle downhill inclines of this sort.
180x150 Etendoir de plafond avec treuil à manivelle ceiling mounted clothes rack Ævar Arnfjörð Bjarmason 2019-02-18 | I bought a pair of these from a French company that's since gone under, really handy to save space. The URL used to be: https://www.ravvie.fr/etendoirs-de-plafond/etendoir-a-linge-a-manivelle.html
Trams backed up to Elandsgracht due to two trams colliding on Rozengracht & Marnixstraat Ævar Arnfjörð Bjarmason 2018-12-07 | ...
Stadler Form Albert uneven fan wheel Ævar Arnfjörð Bjarmason 2018-01-19 | Bought a Stadler Form Albert in The Netherlands from Bol.com in January 2018. This is a view facing down from the top showing a metal fan wheel of some sort that's spinning and oscillating due to apparently being unevenly shaped or installed.It's not audible here but sometimes there's a loud (2x louder than the fan at power setting #3) high frequency metal grinding noise which to me sounds like this wheel is grinding up against something else.
Ginormous house boat being moved on the Kattensloot in Amsterdam Ævar Arnfjörð Bjarmason 2017-05-11 | ...
Helldivers multiplayer connection failures after 5.00 update Ævar Arnfjörð Bjarmason 2016-11-15 | ...
Lindam Sure Shut Orto Safety Gate review: Flaw in the auto-closing mechanism Ævar Arnfjörð Bjarmason 2016-11-03 | My review of the Lindam Sure Shut Orto Safety Gate bought from Amazon.co.uk in February 2016: amazon.co.uk/gp/product/B001KC05Q6Overall I'm happy with these two safety gates, however there's a flaw in the auto-closing mechanism for both as shown in the video, which I've worked around with some rubber bands & duct tape.
Helldivers - The M2016 ‘Constitution’ new with the 5.0 update Ævar Arnfjörð Bjarmason 2016-10-26 | ...
Helldivers bullet time Ævar Arnfjörð Bjarmason 2016-05-27 | HELLDIVERS: SUPER EARTH EDITIONstore.playstation.com/#!/nl-nl/tid=CUSA00231_00
Helldivers - avarinn & solaxys perfect level 12 v.s. Cyborg Ævar Arnfjörð Bjarmason 2016-03-29 | HELLDIVERS: SUPER EARTH EDITIONstore.playstation.com/#!/nl-nl/tid=CUSA00231_00
A car being fished out of the Kattenslot canal in Amsterdam (uncut horizontal) Ævar Arnfjörð Bjarmason 2016-03-17 | ...
A car being fished out of the Kattenslot canal in Amsterdam (uncut) Ævar Arnfjörð Bjarmason 2016-03-16 | ...
A car being fished out of the Kattensloot canal in Amsterdam Ævar Arnfjörð Bjarmason 2016-03-16 | Taken from the intersection of Jakob Catskade and Lodewijk Tripstraat in Westerpark.
Tom Clancys The Division™ - Falling through the floor Ævar Arnfjörð Bjarmason 2016-03-12 | TOM CLANCY'S THE DIVISIONstore.playstation.com/#!/nl-nl/tid=CUSA01262_00
Helldivers - Bugs v.s. Tesla + SH-20 + Static Field Ævar Arnfjörð Bjarmason 2016-03-11 | HELLDIVERS: SUPER EARTH EDITIONstore.playstation.com/#!/nl-nl/tid=CUSA00231_00
Tom Clancys The Division™ - Bug with pacifist enemy who doesnt notice me Ævar Arnfjörð Bjarmason 2016-03-09 | TOM CLANCY'S THE DIVISIONstore.playstation.com/#!/nl-nl/tid=CUSA01262_00
Helldivers bug - The game doesnt recognize that Im dead, enemies attack my corpse Ævar Arnfjörð Bjarmason 2016-02-08 | We had to abort the mission since I wouldn't respawn from Helldiver purgatory.
Helldivers - Fast 8 minute helldive despite the rough start Ævar Arnfjörð Bjarmason 2016-02-06 | Got lucky with the map layout with all the objectives being clustered on one side, also some really good co-op with the recoilless.
Helldivers The level 50 mission Ævar Arnfjörð Bjarmason 2016-01-28 | HELLDIVERS: SUPER EARTH EDITIONstore.playstation.com/#!/nl-nl/tid=CUSA00231_00
