Uploaded September 2021 | Updated November 2026, 35 minutes ago
The Venus Turbo Game Doctor 6M RAM cartridge (it's not a game copier) had two ways to save games to disk. The first was to attach a hardware device called the Game Saver to the back of the TGD6M. That method I cannot show, lacking said hardware.
A second method was to use a special Game Saver disk. Unlike the hardware version, the software version required a disk tailored to the specific game. This disk must be booted before the game and the save state must be written to this specific disk.
In this case, I am not using an original Venus-made conversion but a conversion of Ironsword: Wizards and Warriors II by my friend NewRisingSun. The RAM cartridge makers rarely converted NES games, they almost exclusively converted Japanese licensed Famicom games. There is no analogous support for the mapper Ironsword uses, so it has to be simulated indirectly with the Venus' ASIC.
To use a software Game Saver disk, the Game Saver disk must be loaded first. With the FDSStick, the Game Saver disk is the 5th disk in this set, so I interrupt the boot so I can change which disk is booted (eject by holding down the FDSStick button, then press the button 5 times to load the fifth disk side). Once the Game Saver disk is loaded, it must be removed and Disk A in the series must be loaded with the BOOT menu item. Then the game disks will be loaded, and once done you will see the "Game Saver is Installed" message. The the game should (hopefully) boot.
When the game is playing, you can bring up the save/load menu at any time by pressing the button on the TGD6M. The commands are fairly self explanatory. The Game Saver disk must be in the drive when you wish to save the state or the save will fail. When you return from this menu, either by Cont. or Load, the colors will be incorrect. This is because the software Game Saver does not save the state of the PPU palette. The hardware Game Saver does not have this issue. Usually a transition of some type will correct the palette colors.
For some reason the FDSStick "ejected" the Game Saver disk when I tried to load it the first time, but manually reinserting it fixed the issue. You will notice flashing throughout the first two levels. This does not happen if Ironsword is loaded without the Game Saver disk. The reasons for this are unknown.
The boot process ends at 1:03 in the video, the saving at 7:27 and the loading at 9:40.
The Venus Turbo Game Doctor 6M RAM cartridge (it's not a game copier) had two ways to save games to disk. The first was to attach a hardware device called the Game Saver to the back of the TGD6M. That method I cannot show, lacking said hardware.
A second method was to use a special Game Saver disk. Unlike the hardware version, the software version required a disk tailored to the specific game. This disk must be booted before the game and the save state must be written to this specific disk.
In this case, I am not using an original Venus-made conversion but a conversion of Ironsword: Wizards and Warriors II by my friend NewRisingSun. The RAM cartridge makers rarely converted NES games, they almost exclusively converted Japanese licensed Famicom games. There is no analogous support for the mapper Ironsword uses, so it has to be simulated indirectly with the Venus' ASIC.
To use a software Game Saver disk, the Game Saver disk must be loaded first. With the FDSStick, the Game Saver disk is the 5th disk in this set, so I interrupt the boot so I can change which disk is booted (eject by holding down the FDSStick button, then press the button 5 times to load the fifth disk side). Once the Game Saver disk is loaded, it must be removed and Disk A in the series must be loaded with the BOOT menu item. Then the game disks will be loaded, and once done you will see the "Game Saver is Installed" message. The the game should (hopefully) boot.
When the game is playing, you can bring up the save/load menu at any time by pressing the button on the TGD6M. The commands are fairly self explanatory. The Game Saver disk must be in the drive when you wish to save the state or the save will fail. When you return from this menu, either by Cont. or Load, the colors will be incorrect. This is because the software Game Saver does not save the state of the PPU palette. The hardware Game Saver does not have this issue. Usually a transition of some type will correct the palette colors.
For some reason the FDSStick "ejected" the Game Saver disk when I tried to load it the first time, but manually reinserting it fixed the issue. You will notice flashing throughout the first two levels. This does not happen if Ironsword is loaded without the Game Saver disk. The reasons for this are unknown.
The boot process ends at 1:03 in the video, the saving at 7:27 and the loading at 9:40.










