Uploaded June 2015 | Updated November 2026, 3 hours ago
How To Make A Clock In The Home Machine Shop, Part 9, by Clickspring.
In this episode I use some relatively unusual techniques to make one of the most viewed parts of the clock: The chapter ring.
I show the chemical etching process, using photo resist and ferric chloride, as well as the traditional method of waxing and silvering a clock dial.
Thanks for watching. If you enjoyed the video please give a thumbs up, and leave me a comment.
Join YouTube Channel Memberships here: youtube.com/channel/UCworsKCR-Sx6R6-BnIjS2MA/join
Become a Clickspring Patron here: patreon.com/clickspring/membership
You can also help me make these videos by purchasing via the following Amazon Affiliate links:
Cameras used in this video:
Panasonic GH5 - amzn.to/2rEzhh2
Panasonic X920 - amzn.to/2wzxxdT
Tools & Shop Products:
Dykem 80300 Steel Blue Layout Fluid, Brush-in-Cap (4oz): amzn.to/2HGPaJJ
"Solidworks 2013 Bible": amzn.to/2FObS1D
"Machinery's handbook": amzn.to/2pi7XE5
For more info on this build, as well as other tool making info and plans, visit clickspringprojects.com
Other Videos to Watch:
How To Make A Clock In The Home Machine Shop - Part 8 - Making The Barrel Arbor
youtu.be/b5KwOi-JkEU
Home Machine Shop Tool Making - Machining A Pinion Head Depthing Tool - Part 1
youtu.be/q6xovvpuMQo
Ask Me A Question:
clickspringprojects.com/contact.html
Abbreviated Transcript:
00:40 I'll be using photoresist film to mark out the design, and it needs a completely clean alkili free surface to do its thing. So I scrubbed the surface with emery paper and household vinegar and then cleaned it off with acetone. The result was a clean fresh metal surface.
01:01 I'm going to need this later on, so I'm mixing up the developer solution now. It's a mild alkiline solution thats used to dissolve the unexposed photoresist. The photoresist reacts to UV light, so all work from here on must be done under a yellow light.
01:30 And this is the photoresist. It's a thin light sensitive film, slightly sticky to the touch. It has 3 layers: The photosensitive layer is sandwiched between 2 removable coatings.
02:23 Now if all of the preparation has gone well, then the bond will be strong, and the resist will be well attached across the entire surface of the metal. I've made a simple light box to expose the resist, and a sheet of glass sits on top to position the work.
02 The dial artwork has been printed onto a clear film.
03:52 For the most part, the exposed resist forms a nice crisp line, but inevitably there are small printing flaws that need to be removed like these small dots. I scraped these off with the sharp point of the scriber.
04:22 I glued some small plastic risers on the corners to keep the plate above the bottom surface of the etchant bath, and I've also used clear tape to seal off all of the other surfaces. This center punch mark will help me position the work on the lathe, later on.
04:44 So after all of that preparation, it's finally time to do some etching, and the etchant that I'm using is ferric chloride.
05:15 After sitting in the etch solution for about an hour and a half, the surface is nicely etched, and its ready for the next step. A strong alkaline solution is normally specified to remove the resist, but have a look at what a great job acetone does, its hard to beat that. OK so that's the etching process complete.
05:47 The etched surface is quite pitted, but the edges are crisp, and the overall depth is perfect for accepting the shellac wax. What I need to do now is trim off this excess brass, and form the ring shape. Another job for a super glue arbor on the lathe.
06:39 Traditional dial wax is basically a colored shellac, so in its natural state its quite hard and brittle. But it melts to a sort of maple syrup consistency under a gentle heat. While its in that fluid state, it can be worked into all of the lines and numerals.
07:11 And that brings me to the final step that really makes the chapter ring come to life: The silvering.
07:34 The silvering compound was mixed with a small amount of water, to form a thin paste, and then it was applied by hand. And then it was followed in a similar way with the finishing compound. A gentle heat with the torch finishes off the process, by melting the sanded wax surface, and making it shiny again. A single coat of lacquer, and it's done.
References:
Tony Moss's Excellent Sundial Etching Series:
youtube.com/watch?v=ML37yRmAsOA
youtube.com/watch?v=PAW0q6i7aqg
John Wilding "Large Wheel Skeleton Clock" construction book can be purchased online from Ian T Cobb:
clockmaking-brass.co.uk/clock_construction_books.htmL
How To Make A Clock In The Home Machine Shop, Part 9, by Clickspring.
How To Make A Clock In The Home Machine Shop, Part 9, by Clickspring.
In this episode I use some relatively unusual techniques to make one of the most viewed parts of the clock: The chapter ring.
I show the chemical etching process, using photo resist and ferric chloride, as well as the traditional method of waxing and silvering a clock dial.
Thanks for watching. If you enjoyed the video please give a thumbs up, and leave me a comment.
Join YouTube Channel Memberships here: youtube.com/channel/UCworsKCR-Sx6R6-BnIjS2MA/join
Become a Clickspring Patron here: patreon.com/clickspring/membership
You can also help me make these videos by purchasing via the following Amazon Affiliate links:
Cameras used in this video:
Panasonic GH5 - amzn.to/2rEzhh2
Panasonic X920 - amzn.to/2wzxxdT
Tools & Shop Products:
Dykem 80300 Steel Blue Layout Fluid, Brush-in-Cap (4oz): amzn.to/2HGPaJJ
"Solidworks 2013 Bible": amzn.to/2FObS1D
"Machinery's handbook": amzn.to/2pi7XE5
For more info on this build, as well as other tool making info and plans, visit clickspringprojects.com
Other Videos to Watch:
How To Make A Clock In The Home Machine Shop - Part 8 - Making The Barrel Arbor
youtu.be/b5KwOi-JkEU
Home Machine Shop Tool Making - Machining A Pinion Head Depthing Tool - Part 1
youtu.be/q6xovvpuMQo
Ask Me A Question:
clickspringprojects.com/contact.html
Abbreviated Transcript:
00:40 I'll be using photoresist film to mark out the design, and it needs a completely clean alkili free surface to do its thing. So I scrubbed the surface with emery paper and household vinegar and then cleaned it off with acetone. The result was a clean fresh metal surface.
01:01 I'm going to need this later on, so I'm mixing up the developer solution now. It's a mild alkiline solution thats used to dissolve the unexposed photoresist. The photoresist reacts to UV light, so all work from here on must be done under a yellow light.
01:30 And this is the photoresist. It's a thin light sensitive film, slightly sticky to the touch. It has 3 layers: The photosensitive layer is sandwiched between 2 removable coatings.
02:23 Now if all of the preparation has gone well, then the bond will be strong, and the resist will be well attached across the entire surface of the metal. I've made a simple light box to expose the resist, and a sheet of glass sits on top to position the work.
02 The dial artwork has been printed onto a clear film.
03:52 For the most part, the exposed resist forms a nice crisp line, but inevitably there are small printing flaws that need to be removed like these small dots. I scraped these off with the sharp point of the scriber.
04:22 I glued some small plastic risers on the corners to keep the plate above the bottom surface of the etchant bath, and I've also used clear tape to seal off all of the other surfaces. This center punch mark will help me position the work on the lathe, later on.
04:44 So after all of that preparation, it's finally time to do some etching, and the etchant that I'm using is ferric chloride.
05:15 After sitting in the etch solution for about an hour and a half, the surface is nicely etched, and its ready for the next step. A strong alkaline solution is normally specified to remove the resist, but have a look at what a great job acetone does, its hard to beat that. OK so that's the etching process complete.
05:47 The etched surface is quite pitted, but the edges are crisp, and the overall depth is perfect for accepting the shellac wax. What I need to do now is trim off this excess brass, and form the ring shape. Another job for a super glue arbor on the lathe.
06:39 Traditional dial wax is basically a colored shellac, so in its natural state its quite hard and brittle. But it melts to a sort of maple syrup consistency under a gentle heat. While its in that fluid state, it can be worked into all of the lines and numerals.
07:11 And that brings me to the final step that really makes the chapter ring come to life: The silvering.
07:34 The silvering compound was mixed with a small amount of water, to form a thin paste, and then it was applied by hand. And then it was followed in a similar way with the finishing compound. A gentle heat with the torch finishes off the process, by melting the sanded wax surface, and making it shiny again. A single coat of lacquer, and it's done.
References:
Tony Moss's Excellent Sundial Etching Series:
youtube.com/watch?v=ML37yRmAsOA
youtube.com/watch?v=PAW0q6i7aqg
John Wilding "Large Wheel Skeleton Clock" construction book can be purchased online from Ian T Cobb:
clockmaking-brass.co.uk/clock_construction_books.htmL
How To Make A Clock In The Home Machine Shop, Part 9, by Clickspring.








![The #Antikythera Mechanism Episode 7 - Constructing The Saros & Exeligmos Train
The Antikythera Mechanism Episode 7 - Constructing The #Saros & #Exeligmos Train, by Clickspring
In this video I make the gearing that drives the #eclipse prediction function of the mechanism. Be sure to check out the reference links below for more info on the Saros cycle, and other eclipse related stuff.
[EDIT: At 2:57 there is a typo - the final number in the denominator of the upper expression should be a 30 as per the sketch rather than 90 - Cheers :) ]
Join YouTube Channel Memberships here: https://www.youtube.com/channel/UCworsKCR-Sx6R6-BnIjS2MA/join
Become a Clickspring Patron here: https://www.patreon.com/clickspring/membership
A very special thank you to Patrons:
Sinking Valley Woodworks (http://www.sinkingvalleywoodworks.com)
Glenn Trewitt
Christopher Warnock
Mike Manfrin
John A McCormick
David Wurmfeld
Lonnie Koehn
Michael Harmon
Jim Popwell
Gary Levario
Rollin W. Patrick, Jr.
Pete Askew
Andre van Soest
Larry Pardi
Bernd Fischer
Rudolph Bescherer Jr
Adam Slagle
Jeremiah G. Mort
Olof Haggren
Tim Bray
Steven R. Crider
You can also help me make these videos by purchasing via the following Amazon Affiliate links:
Cameras used in this video:
Panasonic GH5 - https://amzn.to/2rEzhh2
Panasonic X920 - https://amzn.to/2wzxxdT
Tools & Shop Products:
Solidworks 2013 Bible: http://amzn.to/2FObS1D
Gears From The Greeks, Derek de Solla Price: http://amzn.to/2pii4ZD
Sherline Lathe: http://amzn.to/2pnXM19
Dykem 80300 Steel Blue Layout Fluid, Brush-in-Cap (4oz): http://amzn.to/2HGPaJJ
Optivisor Headband Magnifier: http://amzn.to/2HFg1FU
Saint Gobain (Norton) - 4 Arkansas Stones + case: http://amzn.to/2HCOAMX
Hegner Scroll Saw: https://amzn.to/2IhteVW
Super Pike Saw Blades Size 4/0 pkg of 144: http://amzn.to/2IO6aPw
Blue Matador Abrasive Paper - https://amzn.to/2IAFiBT
Abbreviated Transcript:
01:29 This leads to whats known as a Saros series, where over a period of well over a thousand years, roughly 70 to 80 eclipses, will follow one after the other in sequence, separated by the regular interval of 223 lunar months.
05:30 Now the exact nature of that technology is the big question, and we may never know for sure. But we can certainly try a few things out and see what might have been the case. So with that in mind, its time to open up a hole position that I marked back in episode 2. This is the pivot location of the E assembly, and its a perfect opportunity to make the very first hole in the mechanism using some of that ancient tool tech: The Pump Drill.
18:34 The main plate was then opened up, and the square bearing hole formed. These two positions are essentially absolute locations, governed by the dial artwork. And depthing could have been conducted from these positions before filing out this square hole. But at the risk of the position almost certainly moving as the square was formed, and so compromising the depth.
20:44 The height of the Saros pointer assembly is set by the height of the bearing in which it sits, and that height can be easily set by this little spacer. I originally made it slightly oversized, but its a straight forward job to set a clearance of just a few hundredths of a millimeter, by simply abrading the spacer until the barest daylight remains between the adjacent assemblies No special tools, or absolute measurement are required. Just keen eyesight, and a flat abrasive surface.
References:
Gears From The Greeks - Derek de Solla Price: http://amzn.to/2pii4ZD
The CT and PTM data that the AMRP have made publicly available can be found here: http://www.antikythera-mechanism.gr/data
Gear schematic can be found in Tony Freeths 2012 research paper:
http://dlib.nyu.edu/awdl/isaw/isaw-papers/4/
Eclipse and Saros cycle info:
http://www.mreclipse.com/Special/LEprimer.html
http://www.mreclipse.com/Special/SEprimer.html
https://eclipse.gsfc.nasa.gov/SEsaros/SEsaroscat.html
https://eclipse.gsfc.nasa.gov/LEsaros/LEsaroscat.html
https://www.eclipsewise.com/solar/SEhelp/SEperiodicity.html
https://bit.ly/1CjqN0f
http://www.jstor.org/stable/pdf/1006543.pdf
https://en.wikipedia.org/wiki/Babylonian_astronomy
https://en.wikipedia.org/wiki/Sicilian_Expedition
https://en.wikipedia.org/wiki/Battle_of_the_Eclipse
https://theconversation.com/how-eclipses-were-regarded-as-omens-in-the-ancient-world-81248
http://journals.plos.org/plosone/article?id=10.1371/journal.pone.0103275
Credits:
Clips from The 2000 Year Old Computer courtesy Images First Ltd.
Digital image of the Back Dial of The Antikythera mechanism courtesy Tony Freeth, Images First Ltd
Final track is Fading by Sappheiros - visit https://soundcloud.com/sappheirosmusic
Other music:
https://taketones.com,
http://www.epidemicsound.com/
Aerial eclipse footage courtesy NASA
Eclipse Corona footage courtesy Joe Maddox
The Antikythera Mechanism Episode 7 - Making The Saros & Exeligmos Train, by Clickspring The #Antikythera Mechanism Episode 7 - Constructing The Saros & Exeligmos Train](https://i.ytimg.com/vi/vDYnxxUV4Nk/mqdefault.jpg)

