Uploaded December 2015 | Updated November 2026, 18 hours ago
Making A Rectangular Bluing Tray, by Clickspring
It can be a bit hit and miss getting a consistent, uniform blue on long slender parts like clock hands. So I made a third component for the bluing tray set, to do the job right. Using a scrap piece of brass left over from the frames of the current clock build, I used a shop made D bit to mill some grooves so that it could be folded into the shape of a box.
The other videos that this video is related to are:
"Spare Parts #8 - Making A D Bit Single Flute Milling Cutter": youtu.be/jlNxvnOxMCE
"Home Machine Shop Tool Making - Making A Versatile Bluing Tray": youtu.be/8h1Uf9bkc3E
Join YouTube Channel Memberships here: youtube.com/channel/UCworsKCR-Sx6R6-BnIjS2MA/join
Become a Clickspring Patron here: patreon.com/clickspring/membership
You can also help me make these videos by purchasing via the following Amazon Affiliate links:
Cameras used in this video:
Panasonic GH5 - amzn.to/2rEzhh2
Panasonic X920 - amzn.to/2wzxxdT
Tools & Shop Products:
"Solidworks 2013 Bible": amzn.to/2FObS1D
"Milling: A Complete Course (Workshop Practice Series)" - amzn.to/2K2QZ97
"Hardening, Tempering and Heat Treatment (Workshop Practice Series)" - amzn.to/2KbZo6l
Kaowool 24" X 12" X 1" 2400 F Ceramic Fiber Insulation: amzn.to/2pfsM3d
Blue Matador Abrasive Paper - amzn.to/2IAFiBT
Dormer A190202 Jobber Drill Set, 1.0 mm - 6.0 mm x 0.1 mm Size: amzn.to/2DR5fdb
Dormer A190203 Jobber Drill Set, 6.0 mm - 10.0 mm x 0.1 mm Size: amzn.to/2ITfeTa
YG1 NC Spotting Drill 8% Cobalt HSS 1/8 to 1/2" 120 Degree 5 Pc Set CNC Machine: amzn.to/2G7ylv6
Dykem 80300 Steel Blue Layout Fluid, Brush-in-Cap (4oz): amzn.to/2HGPaJJ
Abbreviated Transcript:
00:03 This bluing tray set that I made in a previous video has been working well for bluing screws and other small parts.
00:20 Some of the blued parts coming up in the clock build in the near future, are quite long and thin, so a longer tray will be required when I blue them.
00:29 However the box shape would present a bit of a challenge at the soldering stage if it was made of separate parts, so I'm making it as one piece that can then be folded into shape. Now there a quite a few ways to tackle this job, but I thought I'd show you a mill equivalent of the super glue arbor you've seen me use so often on the lathe
00:54 I'm using this block of aluminium to hold the workpiece, and the first thing I'm going to do is give it a light resurface with this flycutter. The flycutter is shop made, and has quite a lot of mass in the disc, and generally gives me a smooth cut.
01:30 Acetone cleans off the surface, and a light coating of glue is enough to hold the part. Once the work is in position, pressure from the spindle holds it in place as the glue cures.
01:44 I can now machine all of the exposed surfaces in the one operation, starting with the perimeter. I've made this D Bit cutter specifically to cut the v grooves. Click the link if you'd like to see a video showing how this was made.
02:18 The cutter has an included angle of 92 degrees, which is going to help when it comes to bending everything to shape later. I also shifted the cutter across to take a final skim cut on the sides of each groove, to create a little more space for the solder to fill.
02:39 And as always with superglue, a gentle heat breaks the bond. The little corner pieces need to be removed before I can fold the box to shape, so I used a jewellers saw takes care of those, and then I tidied up the saw cut on the belt sander.
03:18 I set about forming it into the shape of a box, with some flux, silver solder and tying wire. Now that the brass is annealed, it bends easily without cracking, leaving a small gap for the solder.
04:30 The brass holds the box shape well when its cool, but it'll flex and sag quite a lot when under heat, so I used some soft tying wire to bind it all together for the soldering operation. A little more flux, and then a good measure of silver solder was placed into position, enough to form a decent fillet when it flows.
05:41 The corners came out quite close and square, but I decided it would be better to round
them off, to match the curve of the bent edges. Then I took the part back to the mill, to form the thread for the handle.
06:14 Now the tray should lean comfortably on the handle when its sitting on the bench, so the feet need to be positioned slightly forward of the center of gravity to achieve this. Using a scrap rod, I decided on a pivot distance that gave a good result, and then formed the holes and threads for the feet.
References:
"The Model Engineers Workshop Manual" pg 94
George H Thomas
The many forum posts on the subject of D Bits
by John "Bogstandard" Moore
Making A Rectangular Bluing Tray, by Clickspring.
Making A Rectangular Bluing Tray, by Clickspring
It can be a bit hit and miss getting a consistent, uniform blue on long slender parts like clock hands. So I made a third component for the bluing tray set, to do the job right. Using a scrap piece of brass left over from the frames of the current clock build, I used a shop made D bit to mill some grooves so that it could be folded into the shape of a box.
The other videos that this video is related to are:
"Spare Parts #8 - Making A D Bit Single Flute Milling Cutter": youtu.be/jlNxvnOxMCE
"Home Machine Shop Tool Making - Making A Versatile Bluing Tray": youtu.be/8h1Uf9bkc3E
Join YouTube Channel Memberships here: youtube.com/channel/UCworsKCR-Sx6R6-BnIjS2MA/join
Become a Clickspring Patron here: patreon.com/clickspring/membership
You can also help me make these videos by purchasing via the following Amazon Affiliate links:
Cameras used in this video:
Panasonic GH5 - amzn.to/2rEzhh2
Panasonic X920 - amzn.to/2wzxxdT
Tools & Shop Products:
"Solidworks 2013 Bible": amzn.to/2FObS1D
"Milling: A Complete Course (Workshop Practice Series)" - amzn.to/2K2QZ97
"Hardening, Tempering and Heat Treatment (Workshop Practice Series)" - amzn.to/2KbZo6l
Kaowool 24" X 12" X 1" 2400 F Ceramic Fiber Insulation: amzn.to/2pfsM3d
Blue Matador Abrasive Paper - amzn.to/2IAFiBT
Dormer A190202 Jobber Drill Set, 1.0 mm - 6.0 mm x 0.1 mm Size: amzn.to/2DR5fdb
Dormer A190203 Jobber Drill Set, 6.0 mm - 10.0 mm x 0.1 mm Size: amzn.to/2ITfeTa
YG1 NC Spotting Drill 8% Cobalt HSS 1/8 to 1/2" 120 Degree 5 Pc Set CNC Machine: amzn.to/2G7ylv6
Dykem 80300 Steel Blue Layout Fluid, Brush-in-Cap (4oz): amzn.to/2HGPaJJ
Abbreviated Transcript:
00:03 This bluing tray set that I made in a previous video has been working well for bluing screws and other small parts.
00:20 Some of the blued parts coming up in the clock build in the near future, are quite long and thin, so a longer tray will be required when I blue them.
00:29 However the box shape would present a bit of a challenge at the soldering stage if it was made of separate parts, so I'm making it as one piece that can then be folded into shape. Now there a quite a few ways to tackle this job, but I thought I'd show you a mill equivalent of the super glue arbor you've seen me use so often on the lathe
00:54 I'm using this block of aluminium to hold the workpiece, and the first thing I'm going to do is give it a light resurface with this flycutter. The flycutter is shop made, and has quite a lot of mass in the disc, and generally gives me a smooth cut.
01:30 Acetone cleans off the surface, and a light coating of glue is enough to hold the part. Once the work is in position, pressure from the spindle holds it in place as the glue cures.
01:44 I can now machine all of the exposed surfaces in the one operation, starting with the perimeter. I've made this D Bit cutter specifically to cut the v grooves. Click the link if you'd like to see a video showing how this was made.
02:18 The cutter has an included angle of 92 degrees, which is going to help when it comes to bending everything to shape later. I also shifted the cutter across to take a final skim cut on the sides of each groove, to create a little more space for the solder to fill.
02:39 And as always with superglue, a gentle heat breaks the bond. The little corner pieces need to be removed before I can fold the box to shape, so I used a jewellers saw takes care of those, and then I tidied up the saw cut on the belt sander.
03:18 I set about forming it into the shape of a box, with some flux, silver solder and tying wire. Now that the brass is annealed, it bends easily without cracking, leaving a small gap for the solder.
04:30 The brass holds the box shape well when its cool, but it'll flex and sag quite a lot when under heat, so I used some soft tying wire to bind it all together for the soldering operation. A little more flux, and then a good measure of silver solder was placed into position, enough to form a decent fillet when it flows.
05:41 The corners came out quite close and square, but I decided it would be better to round
them off, to match the curve of the bent edges. Then I took the part back to the mill, to form the thread for the handle.
06:14 Now the tray should lean comfortably on the handle when its sitting on the bench, so the feet need to be positioned slightly forward of the center of gravity to achieve this. Using a scrap rod, I decided on a pivot distance that gave a good result, and then formed the holes and threads for the feet.
References:
"The Model Engineers Workshop Manual" pg 94
George H Thomas
The many forum posts on the subject of D Bits
by John "Bogstandard" Moore
Making A Rectangular Bluing Tray, by Clickspring.



![The #Antikythera Mechanism Episode 7 - Constructing The Saros & Exeligmos Train
The Antikythera Mechanism Episode 7 - Constructing The #Saros & #Exeligmos Train, by Clickspring
In this video I make the gearing that drives the #eclipse prediction function of the mechanism. Be sure to check out the reference links below for more info on the Saros cycle, and other eclipse related stuff.
[EDIT: At 2:57 there is a typo - the final number in the denominator of the upper expression should be a 30 as per the sketch rather than 90 - Cheers :) ]
Join YouTube Channel Memberships here: https://www.youtube.com/channel/UCworsKCR-Sx6R6-BnIjS2MA/join
Become a Clickspring Patron here: https://www.patreon.com/clickspring/membership
A very special thank you to Patrons:
Sinking Valley Woodworks (http://www.sinkingvalleywoodworks.com)
Glenn Trewitt
Christopher Warnock
Mike Manfrin
John A McCormick
David Wurmfeld
Lonnie Koehn
Michael Harmon
Jim Popwell
Gary Levario
Rollin W. Patrick, Jr.
Pete Askew
Andre van Soest
Larry Pardi
Bernd Fischer
Rudolph Bescherer Jr
Adam Slagle
Jeremiah G. Mort
Olof Haggren
Tim Bray
Steven R. Crider
You can also help me make these videos by purchasing via the following Amazon Affiliate links:
Cameras used in this video:
Panasonic GH5 - https://amzn.to/2rEzhh2
Panasonic X920 - https://amzn.to/2wzxxdT
Tools & Shop Products:
Solidworks 2013 Bible: http://amzn.to/2FObS1D
Gears From The Greeks, Derek de Solla Price: http://amzn.to/2pii4ZD
Sherline Lathe: http://amzn.to/2pnXM19
Dykem 80300 Steel Blue Layout Fluid, Brush-in-Cap (4oz): http://amzn.to/2HGPaJJ
Optivisor Headband Magnifier: http://amzn.to/2HFg1FU
Saint Gobain (Norton) - 4 Arkansas Stones + case: http://amzn.to/2HCOAMX
Hegner Scroll Saw: https://amzn.to/2IhteVW
Super Pike Saw Blades Size 4/0 pkg of 144: http://amzn.to/2IO6aPw
Blue Matador Abrasive Paper - https://amzn.to/2IAFiBT
Abbreviated Transcript:
01:29 This leads to whats known as a Saros series, where over a period of well over a thousand years, roughly 70 to 80 eclipses, will follow one after the other in sequence, separated by the regular interval of 223 lunar months.
05:30 Now the exact nature of that technology is the big question, and we may never know for sure. But we can certainly try a few things out and see what might have been the case. So with that in mind, its time to open up a hole position that I marked back in episode 2. This is the pivot location of the E assembly, and its a perfect opportunity to make the very first hole in the mechanism using some of that ancient tool tech: The Pump Drill.
18:34 The main plate was then opened up, and the square bearing hole formed. These two positions are essentially absolute locations, governed by the dial artwork. And depthing could have been conducted from these positions before filing out this square hole. But at the risk of the position almost certainly moving as the square was formed, and so compromising the depth.
20:44 The height of the Saros pointer assembly is set by the height of the bearing in which it sits, and that height can be easily set by this little spacer. I originally made it slightly oversized, but its a straight forward job to set a clearance of just a few hundredths of a millimeter, by simply abrading the spacer until the barest daylight remains between the adjacent assemblies No special tools, or absolute measurement are required. Just keen eyesight, and a flat abrasive surface.
References:
Gears From The Greeks - Derek de Solla Price: http://amzn.to/2pii4ZD
The CT and PTM data that the AMRP have made publicly available can be found here: http://www.antikythera-mechanism.gr/data
Gear schematic can be found in Tony Freeths 2012 research paper:
http://dlib.nyu.edu/awdl/isaw/isaw-papers/4/
Eclipse and Saros cycle info:
http://www.mreclipse.com/Special/LEprimer.html
http://www.mreclipse.com/Special/SEprimer.html
https://eclipse.gsfc.nasa.gov/SEsaros/SEsaroscat.html
https://eclipse.gsfc.nasa.gov/LEsaros/LEsaroscat.html
https://www.eclipsewise.com/solar/SEhelp/SEperiodicity.html
https://bit.ly/1CjqN0f
http://www.jstor.org/stable/pdf/1006543.pdf
https://en.wikipedia.org/wiki/Babylonian_astronomy
https://en.wikipedia.org/wiki/Sicilian_Expedition
https://en.wikipedia.org/wiki/Battle_of_the_Eclipse
https://theconversation.com/how-eclipses-were-regarded-as-omens-in-the-ancient-world-81248
http://journals.plos.org/plosone/article?id=10.1371/journal.pone.0103275
Credits:
Clips from The 2000 Year Old Computer courtesy Images First Ltd.
Digital image of the Back Dial of The Antikythera mechanism courtesy Tony Freeth, Images First Ltd
Final track is Fading by Sappheiros - visit https://soundcloud.com/sappheirosmusic
Other music:
https://taketones.com,
http://www.epidemicsound.com/
Aerial eclipse footage courtesy NASA
Eclipse Corona footage courtesy Joe Maddox
The Antikythera Mechanism Episode 7 - Making The Saros & Exeligmos Train, by Clickspring The #Antikythera Mechanism Episode 7 - Constructing The Saros & Exeligmos Train](https://i.ytimg.com/vi/vDYnxxUV4Nk/mqdefault.jpg)






