Uploaded January 2018 | Updated September 2026, 1 week ago
Hey guys! Just can't get enough of this Kalman filter. You see, I have been having a really hard time tuning my quads with biblades since 3.2 rolled out. No matter what I tried tuning the biblades was next to impossible and I was never 100% happy with the tune.
Enter Kalman filters and holy crap! Now my biblades fly even better than they did in 3.1.7
Not only that but I am a believer in the 32bit ESC's.. after building an F4 + 32bit to test and see how it compared with teh F7 + 32bit I am quite convinced that the secret sauce on that quad was the ESC's.
Check out the video and see for yourself!
[ LINKS ]
Download BF 3.3 W/ Kalman - bit.ly/2G65W4C
Hey guys! Just can't get enough of this Kalman filter. You see, I have been having a really hard time tuning my quads with biblades since 3.2 rolled out. No matter what I tried tuning the biblades was next to impossible and I was never 100% happy with the tune.
Enter Kalman filters and holy crap! Now my biblades fly even better than they did in 3.1.7
Not only that but I am a believer in the 32bit ESC's.. after building an F4 + 32bit to test and see how it compared with teh F7 + 32bit I am quite convinced that the secret sauce on that quad was the ESC's.
Check out the video and see for yourself!
[ LINKS ]
Download BF 3.3 W/ Kalman - bit.ly/2G65W4C
![CLEARVIEW + Element6Drones APEX Maiden ♠ [ FPV FREESTYLE ]](https://i.ytimg.com/vi/ThND7ytWGWQ/mqdefault.jpg "CLEARVIEW + Element6Drones APEX Maiden ♠ [ FPV FREESTYLE ]
Hey guys! I finally got the chance to Maiden the APEX now that the weather cleared a bit and just in time to try out the new Clearview RACE set that I got.
Really blown away on the performance of both of these so look forward to a full Tune guide on the APEX and a review on the Clearview.
This was just a bit of testing I was doing with the APEX - I am super impressed with Betaflight 3.2 RC6 so I am going to flash it to 3.2.1 next before doing the tuning video")
![HELIO RC - HELIOSPRING + ButterFlight Stock PID [ MAIDEN ]](https://i.ytimg.com/vi/UcVnRmzcXtg/mqdefault.jpg "HELIO RC - HELIOSPRING + ButterFlight Stock PID [ MAIDEN ]
So here we have it guys, took me about 3 hours to build with the HELIO FC using a Matek PDB. Overall I am pretty happy with the layout. The weird corner motor pads actually work really damn well and keep the wires off the top of the FC.
This DVR is entirely STOCK settings - all I did was set RX / Failsafe / Rates and run the IMUF update. It flew freaking great though a bit too loose for my liking. The next flight I cranked P gain, went a lil too far.. backed it up in the next flight and it was perfection.
Will post the post-tune flight later.
[ HELIO RC BUILD ]
Helio Spring FC
Butterflight 3.4.2 - 16/16khz
DYS Aria - 32bit ESC / 42khz pwm - DSHOT 1200
Deadpool 2306/2400kv
Gemfan 5152 Biblades")
![Flying Two Bladed Propellers - Beginner to Advanced ♠ [ GIT GUD SERIES ] - Beginner Help Series](https://i.ytimg.com/vi/Uj9M1ADTnrw/mqdefault.jpg "Flying Two Bladed Propellers - Beginner to Advanced ♠ [ GIT GUD SERIES ] - Beginner Help Series
Hey guys, ever since I posted that video about my woes with Biblades on RC4 many people have asked questions about it or plainly told me I was crazy to pursue them... so I decided to make a little video here to tell you guys a bit about my reasons for using them and what the secret is for flying them.")
![Bent Prop ButterHawk - Emax Babyhawk R + Butterflight 3.5.0 [ FREESTYLE ]](https://i.ytimg.com/vi/VmeEUOL85uc/mqdefault.jpg "Bent Prop ButterHawk - Emax Babyhawk R + Butterflight 3.5.0 [ FREESTYLE ]
I flew a good portion of that pack with a bent prop. Not just a bent prop, an accordion bent prop and I barely even noticed it. Only thing that clued me in something was wrong was a tiny bit more propwash than normal.
Cant wait to bring you guys more info on the latest airbot stuff I am testing =D")
![Betaflight 3.2.1(stable) - How to Flash and Setup Your Quad! - [ How To Quad ]](https://i.ytimg.com/vi/_o0h22OQUxc/mqdefault.jpg "Betaflight 3.2.1(stable) - How to Flash and Setup Your Quad! - [ How To Quad ]
As promised on my last video, here is the flashing & tuning guide on Betaflight 3.2.1 - this is a quick video, I am not going to go into a ton of detail on what each setting does and its historical provenance. I am just going to show you guys how I Flash and set up my quads before the maiden.
Tuning the quad is a whole separate matter and should be done out in the field after a couple test flights.
Hope this helps some of you out there and dont hesitate to drop a comment with questions and what not.
[ Video INDEX ] Use this section to skip ahead
3:31 - Set Board to DFU for FLASHING!
4:39 - Selecting Betaflight Firmware and Flashing
5:55 - Quadcopter Setup Screen
6:21 - Uart Ports Screen and Ports Setup
6:53 - Betaflight Configuration Screen
10:20 - Radio Receiver Setup Screen
10:57 - Betaflight Modes & Switches Tab
11:34 - Quadcopter Failsafe Settings
12:04 - Betaflight PID & Rates Setup Screen
13:10 - Betaflight Notch Filter Settings Screen
16:11 - Betaflight Motors Tab
16:30 - Blackbox Settings Screen
*** DISCLAIMER ***
I was made aware that the configurator was updated on Google Play as of this morning. I had already shot and edited the video, so I am not going to re-do it. Either way, if you run bleeding edge Betaflight ( daily builds ) its good to get in the habit of manually updating the configurator. If your configurator already says 10 then you are good to go.")
![STRICTLY RACING DRONES 5 - BUILD TIME! ♠ [ FPV DRONE BUILD ] (re-upload)](https://i.ytimg.com/vi/bMVmhRSreQw/mqdefault.jpg "STRICTLY RACING DRONES 5 - BUILD TIME! ♠ [ FPV DRONE BUILD ] (re-upload)
STRICTLY RACING DRONES 5 - BUILD TIME! ♠ [ FPV DRONE BUILD ] (re-upload)")
![FRSky F-Port Protocol - The SBUS Killer!! [ LOOSE VLOG ]](https://i.ytimg.com/vi/bY9BnNLBz60/mqdefault.jpg "FRSky F-Port Protocol - The SBUS Killer!! [ LOOSE VLOG ]
Hey guys! Finally got some time to do some research and bring you guys some fresh tasty info. Looks like FRSky is working on a new RX protocol to deliver RX Control and TELEMETRY over a single wire connection.
F-Port is structured much like SBUS is except it uses an uninverted signal - meaning you dont need to fuck around with inversion anymore to get stuff to work. You also get Telemetry and control out of a single port which is pretty awesome.
[ LINKS ]
Betaflight Install Instructions - http://bit.ly/2A0idrn
F-Port Spec Documentation - http://bit.ly/2jW76JL")
![Flying From Your Car - Beginner to Advanced [ GIT GUD SERIES ]](https://i.ytimg.com/vi/bYEC7XHVby4/mqdefault.jpg "Flying From Your Car - Beginner to Advanced [ GIT GUD SERIES ]
As promised, I am back with a video on how I do my flying from the car. There is not much secret to it guys - just your normal everyday gear will do the job, its really more about being cogniscent of your range and of objects between you and the quad.
Hope you guys enjoy and if you have any questions just drop me a line!")
![CL RACING F4 - Flight Controller Overview - [ REVIEW ]](https://i.ytimg.com/vi/cB2P00UdCxw/mqdefault.jpg "CL RACING F4 - Flight Controller Overview - [ REVIEW ]
Beaver FPV Just got in the new CL RACING F4S with all the new updates and goodies. If you are a fan of the show you know the CLRACING F4 has become my go-to FC because of its dependability, performance and ease of use.
The new CLRACING takes that a step further with Camera Control support, dedicated Uart inversion for telemetry and much more!
Check out the video for a full overview and comparison with the old CLRACING FC.
Dont forget to SUBSCRIBE for more awesome stuff like this!
[ LINKS ]
Buy CLRACING F4 from Beaver FPV - http://bit.ly/2ySrOQf
CLRACING F4 V2 Manual - http://bit.ly/2gPuiIa")
