Uploaded July 2020 | Updated September 2026, 2 weeks ago
Buy One!
Today we'll be testing various batteries I have laying around the shop, using a Battery Load Tester. All 4 batteries have been selected for this test, because they all show a different reading.
Voltage;
A load tester has a volt meter, so it will 1st show the surface charge of a battery and display that in volts. It will also show whether or not the charging system of the equipment you're working on is functioning properly, as it should display a higher voltage when the engine is running (and the magneto/alternator is charging the battery).
Amperes;
This battery load tester works by using a coiled filament inside of the tester, and when activated, this filament acts as a resistor, which will simulate a starter being engaged.
A starter creates a high amp drain on a battery, and even though a battery may show a 12v charge, it may not have the ampere output that the starter requires to turn over the engine.
Therefore, a load tester can be used to diagnose, and/or eliminate a battery as a cause of a no-start issue.
For example, you have a vehicle or riding lawn mower that doesn't start, or even turn over the engine, because the starter will not engage.
Using a multi-meter, you test the battery and it shows it holds a charge of more than 12v, so you assume the battery isn't the issue.
You could then spend valuable time searching for other issues that may not exist, as the battery may not put out the amperes needed to engage the starter.
This test can be performed on or off the vehicle. However, to test the charging circuit, the battery will need to be hooked up, with the vehicle running.
_______________________________________________
If you enjoyed the video, hit LIKE & SUBSCRIBE!
New videos every week!
SOCIAL MEDIA:
Instagram: ELMN80R
facebook.com/EliminatorPerformance
twitter.com/EliminatorPerf
youtube.com/eliminatorperformance
DONATE:
paypal.me/ELMN80R
Bitcoin: 1NYgPvcvBWuhGRewsLE4Scy1cbzwndh5hZ
2ND CHANNEL:
EP Vlogs: youtube.com/channel/UCqati-ozlK-ADoRc6jG0YhQ
GEAR:
Camera: amzn.to/2HVkW9o
Tripod: amzn.to/2HGWt4w
Microphone: amzn.to/2J7k9DA
Cheap Mic: amzn.to/2xCBn6z
Headphones: amzn.to/2JeHUG9
Editing Software: amzn.to/2JD7OTx
Photoshop: amzn.to/2HBY6Ez
MUSIC:
Intro/Outro Music: Burnt - Jingle Punks
Buy One!
Today we'll be testing various batteries I have laying around the shop, using a Battery Load Tester. All 4 batteries have been selected for this test, because they all show a different reading.
Voltage;
A load tester has a volt meter, so it will 1st show the surface charge of a battery and display that in volts. It will also show whether or not the charging system of the equipment you're working on is functioning properly, as it should display a higher voltage when the engine is running (and the magneto/alternator is charging the battery).
Amperes;
This battery load tester works by using a coiled filament inside of the tester, and when activated, this filament acts as a resistor, which will simulate a starter being engaged.
A starter creates a high amp drain on a battery, and even though a battery may show a 12v charge, it may not have the ampere output that the starter requires to turn over the engine.
Therefore, a load tester can be used to diagnose, and/or eliminate a battery as a cause of a no-start issue.
For example, you have a vehicle or riding lawn mower that doesn't start, or even turn over the engine, because the starter will not engage.
Using a multi-meter, you test the battery and it shows it holds a charge of more than 12v, so you assume the battery isn't the issue.
You could then spend valuable time searching for other issues that may not exist, as the battery may not put out the amperes needed to engage the starter.
This test can be performed on or off the vehicle. However, to test the charging circuit, the battery will need to be hooked up, with the vehicle running.
_______________________________________________
If you enjoyed the video, hit LIKE & SUBSCRIBE!
New videos every week!
SOCIAL MEDIA:
Instagram: ELMN80R
facebook.com/EliminatorPerformance
twitter.com/EliminatorPerf
youtube.com/eliminatorperformance
DONATE:
paypal.me/ELMN80R
Bitcoin: 1NYgPvcvBWuhGRewsLE4Scy1cbzwndh5hZ
2ND CHANNEL:
EP Vlogs: youtube.com/channel/UCqati-ozlK-ADoRc6jG0YhQ
GEAR:
Camera: amzn.to/2HVkW9o
Tripod: amzn.to/2HGWt4w
Microphone: amzn.to/2J7k9DA
Cheap Mic: amzn.to/2xCBn6z
Headphones: amzn.to/2JeHUG9
Editing Software: amzn.to/2JD7OTx
Photoshop: amzn.to/2HBY6Ez
MUSIC:
Intro/Outro Music: Burnt - Jingle Punks


![MBRP Side Exit Exhaust [BEFORE & AFTER] - 2019 F150 5.0L
Before & After!
I installed an MBRP Pro Series Side Exit Exhaust on my 2019 RCSB Ford F150 with a 5.0L V8!
Part Number: MBRP S5260304
This is a 3 Pro Series, 304 Stainless Steel, Side Exit, Full Cat-Back Exhaust System!
Click Here for the Installation Video: https://youtu.be/BE5EYuw-fus
Exhaust Tips were leveled out after filming this video!
If you enjoyed the video, hit LIKE & SUBSCRIBE!
New videos every week!
SOCIAL MEDIA:
https://www.facebook.com/EliminatorPerformance
https://twitter.com/EliminatorPerf
https://www.youtube.com/eliminatorperformance
2ND CHANNEL:
EP Vlogs: https://www.youtube.com/channel/UCqati-ozlK-ADoRc6jG0YhQ
GEAR:
Camera: https://amzn.to/2HVkW9o
Tripod: https://amzn.to/2HGWt4w
Microphone: https://amzn.to/2J7k9DA
Cheap Mic: https://amzn.to/2xCBn6z
Headphones: https://amzn.to/2JeHUG9
Editing Software: https://amzn.to/2JD7OTx
Photoshop: https://amzn.to/2HBY6Ez
DONATE:
Bitcoin: 1NYgPvcvBWuhGRewsLE4Scy1cbzwndh5hZ
MUSIC:
Intro/Outro Music: Burnt - Jingle Punks MBRP Side Exit Exhaust [BEFORE & AFTER] - 2019 F150 5.0L](https://i.ytimg.com/vi/s1gQXJoWKCE/mqdefault.jpg)







