Uploaded August 2022 | Updated November 2026, 3 hours ago
Here's one way the AVOCET ABS can go back together again.
of interest to aspiring purple belt/brown belt pickers.
there are several great vids on picking and gutting this lock - finding none on reassembly - which put the fears in me - here's a version putting it back together.
CORE ITEM - three shims. Really.
and if you take this apart you already know a .9mm hex driver is necessary.
There are a few phases - in the timings below - and a couple gotchas that the shims will mitigate. some of the vid is sped up because - well - this is a guide of what to expect - rather than expecting you to go with me every second of working this out.
inspired by PeaceWeapon's (youtube.com/user/PeaceweaponPT) text overlay vids (eg youtube.com/watch?v=RcYysZLknS8), this REASSEMBLE presentation is also just text on video - so please put on the tunes of your choice while listening (i have the jazz soul of oscar peterson on right now, alternating with metalica some kind of monster)
00:00 start
00:12 Phase 1 - trap pin putting - with double shims in the core.
00:57 - a few trap pins being inserted - the word fiddly comes to mind
02:08 Phase 2 - key pin prep - a bit of a breather here
04:08 Phase 3 - getting driver pins/springs together
06:27 Phase 4 - plug going back into core - prep those shims!
08:45 Phase 4 con't - figure out that a third shim is The Answer for Driver Pin bother
09:40 - put in ball bearing at lip of plug for centering in core when turns
11:20 Phase 5 - put in the mushroom cloud plate to hold core in place
14:20 - key turn check...and plate adjustment
15:09 - recheck and go!
- note 1 - EXTRA BRASS BIT - WHAT CHAMBER? i didn't show it in the vid, but there's one wee brass bit that goes - in this lock- at the bottom of the 3rd driver pin chamber - have only seen that in the LPL vid and he doesn't talk about it :)
I found which chamber by testing each with a paper clip to see which one was deeper. No. 3 it was. Maybe it just doesn't come loose in many locks?? anyway - thar ya go.
-note 2 - CIRCLIP HOLDING CORE there is a circlip around the external chamber that it seems many folks do not need to remover to get the core out - i needed to remove it for extraction but NOT for insertion. i was also able to squish it back into shape an put it back into the core so that it's flush again with the core. You may or may not need to remove that after taking out the mushroom cloud plate via the tiny grub screws.
THANKS - many many
u/GeorgiaJim (youtube.com/channel/UCd2U2lOG9BE3Alh_KJ4lKLA)
at LPU lockpicking on Reddit for the multi-shim approach on the trap pins.
also great vids for pick and gut:
dmac (youtu.be/1Xoxx_HKCGk)
yabende (youtu.be/8xCwX1o0AfI)
LPL (youtu.be/zq5rGjt-9rQ)
and lock noob - just explaining this thing in the redoubtable 360 (youtu.be/JHyHH5A5Eqo)
[daz evers shows it's possible - but lawd, he makes things look so incredibly easy... (youtu.be/jZSwPlGIfO4) ]
WAS THIS VID HELPFUL?
Here's one way the AVOCET ABS can go back together again.
of interest to aspiring purple belt/brown belt pickers.
there are several great vids on picking and gutting this lock - finding none on reassembly - which put the fears in me - here's a version putting it back together.
CORE ITEM - three shims. Really.
and if you take this apart you already know a .9mm hex driver is necessary.
There are a few phases - in the timings below - and a couple gotchas that the shims will mitigate. some of the vid is sped up because - well - this is a guide of what to expect - rather than expecting you to go with me every second of working this out.
inspired by PeaceWeapon's (youtube.com/user/PeaceweaponPT) text overlay vids (eg youtube.com/watch?v=RcYysZLknS8), this REASSEMBLE presentation is also just text on video - so please put on the tunes of your choice while listening (i have the jazz soul of oscar peterson on right now, alternating with metalica some kind of monster)
00:00 start
00:12 Phase 1 - trap pin putting - with double shims in the core.
00:57 - a few trap pins being inserted - the word fiddly comes to mind
02:08 Phase 2 - key pin prep - a bit of a breather here
04:08 Phase 3 - getting driver pins/springs together
06:27 Phase 4 - plug going back into core - prep those shims!
08:45 Phase 4 con't - figure out that a third shim is The Answer for Driver Pin bother
09:40 - put in ball bearing at lip of plug for centering in core when turns
11:20 Phase 5 - put in the mushroom cloud plate to hold core in place
14:20 - key turn check...and plate adjustment
15:09 - recheck and go!
- note 1 - EXTRA BRASS BIT - WHAT CHAMBER? i didn't show it in the vid, but there's one wee brass bit that goes - in this lock- at the bottom of the 3rd driver pin chamber - have only seen that in the LPL vid and he doesn't talk about it :)
I found which chamber by testing each with a paper clip to see which one was deeper. No. 3 it was. Maybe it just doesn't come loose in many locks?? anyway - thar ya go.
-note 2 - CIRCLIP HOLDING CORE there is a circlip around the external chamber that it seems many folks do not need to remover to get the core out - i needed to remove it for extraction but NOT for insertion. i was also able to squish it back into shape an put it back into the core so that it's flush again with the core. You may or may not need to remove that after taking out the mushroom cloud plate via the tiny grub screws.
THANKS - many many
u/GeorgiaJim (youtube.com/channel/UCd2U2lOG9BE3Alh_KJ4lKLA)
at LPU lockpicking on Reddit for the multi-shim approach on the trap pins.
also great vids for pick and gut:
dmac (youtu.be/1Xoxx_HKCGk)
yabende (youtu.be/8xCwX1o0AfI)
LPL (youtu.be/zq5rGjt-9rQ)
and lock noob - just explaining this thing in the redoubtable 360 (youtu.be/JHyHH5A5Eqo)
[daz evers shows it's possible - but lawd, he makes things look so incredibly easy... (youtu.be/jZSwPlGIfO4) ]
WAS THIS VID HELPFUL?










