Uploaded March 2026 | Updated November 2026, 26 minutes ago
Introducing CMSIS Support for Microchip Devices - A Video Series Playlist:
youtube.com/playlist?list=PLtQdQmNK_0DSEMwrcH-ami2vS4No4ev-T
Practical demonstration of loading and running the CMSIS Driver Example for the PIC32CM PL10 Curiosity Nano board in VS Code. We explore the code (GPIO UART driver usage, switch-triggered message), perform basic debugging with breakpoints, use the built-in CMSIS Serial Monitor to observe UART output, and show how to easily change the baud rate via config file (with live sync to code) — all within the CMSIS Solution environment. Engineer-focused: clean workflow, no fluff, highlighting code completion, config-driven changes, and simple debug/monitor integration.
00:00 – Recap: Blinky from previous video + Data Visualizer verification 00:33 – Closing Blinky → loading the Driver Example
00:49 – Browse folder, select project, Git init option
01:02 – Environment setup during solution creation
01:13 – README preview: GPIO + UART demo, LED toggle, switch monitor, UART message
01:33 – System clock 24 MHz, SysTick 1 ms ticks
01:45 – Code dive: UART driver instance pointer → API code completion
02:02 – Build → start debug session
02:26 – Set breakpoint at UART send
02:34 – Debug run → hit main start
02:48 – Resume → press button to hit breakpoint
02:59 – CMSIS Debugger extensions: Serial Monitor in new terminal
03:17 – Open Serial Monitor → auto-detects Curiosity Nano virtual COM 03:28 – Start monitoring → button presses send responsive "Switch pressed" messages
03:41 – Default baud rate 115200 confirmed
03:47 – Changing baud rate: UART config overview (async, no parity, 8N1) 03:59 – Edit config.uart → change to 9600
04:13 – Save → code syncs to 9600 04:22 – Rebuild & run (no debug needed)
04:35 – Serial Monitor at 9600 → messages still visible (after host-side match)
04:49 – Revert to 115200 directly in code → rebuild & run
05:11 – Back to normal output
05:18 – Summary: Basic debugging + serial in CMSIS flow
Introducing CMSIS Support for Microchip Devices - A Video Series Playlist:
youtube.com/playlist?list=PLtQdQmNK_0DSEMwrcH-ami2vS4No4ev-T
Practical demonstration of loading and running the CMSIS Driver Example for the PIC32CM PL10 Curiosity Nano board in VS Code. We explore the code (GPIO UART driver usage, switch-triggered message), perform basic debugging with breakpoints, use the built-in CMSIS Serial Monitor to observe UART output, and show how to easily change the baud rate via config file (with live sync to code) — all within the CMSIS Solution environment. Engineer-focused: clean workflow, no fluff, highlighting code completion, config-driven changes, and simple debug/monitor integration.
00:00 – Recap: Blinky from previous video + Data Visualizer verification 00:33 – Closing Blinky → loading the Driver Example
00:49 – Browse folder, select project, Git init option
01:02 – Environment setup during solution creation
01:13 – README preview: GPIO + UART demo, LED toggle, switch monitor, UART message
01:33 – System clock 24 MHz, SysTick 1 ms ticks
01:45 – Code dive: UART driver instance pointer → API code completion
02:02 – Build → start debug session
02:26 – Set breakpoint at UART send
02:34 – Debug run → hit main start
02:48 – Resume → press button to hit breakpoint
02:59 – CMSIS Debugger extensions: Serial Monitor in new terminal
03:17 – Open Serial Monitor → auto-detects Curiosity Nano virtual COM 03:28 – Start monitoring → button presses send responsive "Switch pressed" messages
03:41 – Default baud rate 115200 confirmed
03:47 – Changing baud rate: UART config overview (async, no parity, 8N1) 03:59 – Edit config.uart → change to 9600
04:13 – Save → code syncs to 9600 04:22 – Rebuild & run (no debug needed)
04:35 – Serial Monitor at 9600 → messages still visible (after host-side match)
04:49 – Revert to 115200 directly in code → rebuild & run
05:11 – Back to normal output
05:18 – Summary: Basic debugging + serial in CMSIS flow










