Uploaded January 2017 | Updated September 2026, 2 weeks ago
In this tutorial we will learn how to control our LEDs with using TV or IR remote. After this tutorial, you can control everything with your TV or IR remote.
Required Hardware
Arduino Board:
goo.gl/Rqc5w2
amzn.to/2LZr6t4
IR Receiver Module Kit:
goo.gl/PwBgFm
amzn.to/2PEW6QP
IR Sensor Only Receiver :
goo.gl/hWqnJ7
amzn.to/2PLnLQ8
LED:
goo.gl/CPAXXf
amzn.to/3qxSs8O
220ohm Resistor :
goo.gl/FVgEyR
amzn.to/3jXMJXs
Breadboard :
goo.gl/GjpqVW
amzn.to/3qxLxwm
CR2025 Coin Battery :
goo.gl/ot2BJz
amzn.to/3u7Gp3y
Jumper Wires:
amzn.to/3doetmT
Recommended Items:
Use Your Muscles in Project - amzn.to/3wdL45C
37 Sensor & Module Packages - amzn.to/3m66WeQ
Try this Robot Arm - amzn.to/3fq8DCl
Best Resin 3D Printer - amzn.to/39tY8KB
Arduino Compatible Kits - bit.ly/2J2AFF7
Banggood Spring Sale - bit.ly/3slMbOn
About IR :
Infrared (IR) controls are often used in most electronic devices.
This LED will give a predefined code when we press any key on the remote control and a certain frequency will also flash.
The 38 kHz infrared receiver we use in the project demodulates the signal it receives and sends the button code to the Arduino. We can use with this receiver as long as different brand and model remote controls have 38 kHz carrier signal.The receiver has 3 pins. These are GND - VCC - Signal respectively.
About Hex code :
First we must find the hex codes of the buttons of remote controller.
This way you can use another remote control instead of the included in the kit. So if you have only receiver, you can use any TV remote control. We will use the IRrecvDump example code.
Download IR library: goo.gl/INTfWC
Uncompress the ZIP or RAR file onto your desktop
Place the folder into your arduinosketchfolder/libraries folder
Rename the uncompressed folder IRremote
Download Source Code: create.arduino.cc/editor/mertarduinotech/9d107596-a93d-4406-835e-ecf8d63f189b/preview
Social Media:
instagram.com/mertarduino
facebook.com/mertarduino
In this tutorial we will learn how to control our LEDs with using TV or IR remote. After this tutorial, you can control everything with your TV or IR remote.
Required Hardware
Arduino Board:
goo.gl/Rqc5w2
amzn.to/2LZr6t4
IR Receiver Module Kit:
goo.gl/PwBgFm
amzn.to/2PEW6QP
IR Sensor Only Receiver :
goo.gl/hWqnJ7
amzn.to/2PLnLQ8
LED:
goo.gl/CPAXXf
amzn.to/3qxSs8O
220ohm Resistor :
goo.gl/FVgEyR
amzn.to/3jXMJXs
Breadboard :
goo.gl/GjpqVW
amzn.to/3qxLxwm
CR2025 Coin Battery :
goo.gl/ot2BJz
amzn.to/3u7Gp3y
Jumper Wires:
amzn.to/3doetmT
Recommended Items:
Use Your Muscles in Project - amzn.to/3wdL45C
37 Sensor & Module Packages - amzn.to/3m66WeQ
Try this Robot Arm - amzn.to/3fq8DCl
Best Resin 3D Printer - amzn.to/39tY8KB
Arduino Compatible Kits - bit.ly/2J2AFF7
Banggood Spring Sale - bit.ly/3slMbOn
About IR :
Infrared (IR) controls are often used in most electronic devices.
This LED will give a predefined code when we press any key on the remote control and a certain frequency will also flash.
The 38 kHz infrared receiver we use in the project demodulates the signal it receives and sends the button code to the Arduino. We can use with this receiver as long as different brand and model remote controls have 38 kHz carrier signal.The receiver has 3 pins. These are GND - VCC - Signal respectively.
About Hex code :
First we must find the hex codes of the buttons of remote controller.
This way you can use another remote control instead of the included in the kit. So if you have only receiver, you can use any TV remote control. We will use the IRrecvDump example code.
Download IR library: goo.gl/INTfWC
Uncompress the ZIP or RAR file onto your desktop
Place the folder into your arduinosketchfolder/libraries folder
Rename the uncompressed folder IRremote
Download Source Code: create.arduino.cc/editor/mertarduinotech/9d107596-a93d-4406-835e-ecf8d63f189b/preview
Social Media:
instagram.com/mertarduino
facebook.com/mertarduino
