Uploaded May 2025 | Updated November 2026, 1 day ago
Amplitude Modulation playlist. Watch these video to understand more on Amplitude Modulation.
youtube.com/watch?v=8BniBC4fuWY&list=PLFxhgwM1F4yyXTMfVhAyN7Hd-YfcdZQWj
For access to this presentation materials, membership is required: I need the Material PPT
Sent me an email to Technologies.Discussion@gmail.com
If you need the whole playlist material, send me email and we discuss.
Give me some time to response. Thanks.
Why we need Modulation
Direct transmission of baseband signal like voice, TV signals, etc, without using modulation is undesirable because:
Large Antenna Required for Low Frequency Baseband Signal
Simultaneous Transmission of Baseband Signal Cause Interference
Noise and Interference. Improved Signal Quality
Efficient Transmission Over Distances for Wireless Communication
Adaptation to Transmission Medium
In Amplitude Modulation (AM), the modulating signal (data) is used to modulate the amplitude of the carrier signal. The top and bottom envelope of the modulated carrier have the same shape as the modulating signal. In other words, the amplitude of the carrier is made to change according to the shape of the modulating signal.
The modulated carrier frequency remains unchanged at the carrier frequency.
Amplitude Modulation (AM) is a modulation technique used in electronic communication, most commonly for transmitting information via a radio carrier wave. In AM, the amplitude (strength) of the carrier wave is varied in proportion to the waveform of the message signal (such as voice or music), while the frequency and phase remain constant.
Equation for a single-frequency sinusoidal modulating (baseband) signal is given by: em(t) = Em cos 2fmt
where Em is the peak amplitude of the modulating signal
fm is the frequency of the modulating signal
The equation of the unmodulated (when not ‘carrying’ any information) carrier is given by: ec(t) = Ec cos 2fct
where Ec is the peak amplitude of the unmodulated carrier (constant)
fc is the frequency of the unmodulated carrier
Then, the equation for the modulated carrier is given by:
eAM (t) = (Ec + em(t))cos 2fct = (Ec + Emcos 2fmt)cos 2fct
eAM (t) = Ec(1 + mcos 2fmt) cos 2fct
Amplitude Modulation playlist. Watch these video to understand more on Amplitude Modulation.
youtube.com/watch?v=8BniBC4fuWY&list=PLFxhgwM1F4yyXTMfVhAyN7Hd-YfcdZQWj
For access to this presentation materials, membership is required: I need the Material PPT
Sent me an email to Technologies.Discussion@gmail.com
If you need the whole playlist material, send me email and we discuss.
Give me some time to response. Thanks.
Why we need Modulation
Direct transmission of baseband signal like voice, TV signals, etc, without using modulation is undesirable because:
Large Antenna Required for Low Frequency Baseband Signal
Simultaneous Transmission of Baseband Signal Cause Interference
Noise and Interference. Improved Signal Quality
Efficient Transmission Over Distances for Wireless Communication
Adaptation to Transmission Medium
In Amplitude Modulation (AM), the modulating signal (data) is used to modulate the amplitude of the carrier signal. The top and bottom envelope of the modulated carrier have the same shape as the modulating signal. In other words, the amplitude of the carrier is made to change according to the shape of the modulating signal.
The modulated carrier frequency remains unchanged at the carrier frequency.
Amplitude Modulation (AM) is a modulation technique used in electronic communication, most commonly for transmitting information via a radio carrier wave. In AM, the amplitude (strength) of the carrier wave is varied in proportion to the waveform of the message signal (such as voice or music), while the frequency and phase remain constant.
Equation for a single-frequency sinusoidal modulating (baseband) signal is given by: em(t) = Em cos 2fmt
where Em is the peak amplitude of the modulating signal
fm is the frequency of the modulating signal
The equation of the unmodulated (when not ‘carrying’ any information) carrier is given by: ec(t) = Ec cos 2fct
where Ec is the peak amplitude of the unmodulated carrier (constant)
fc is the frequency of the unmodulated carrier
Then, the equation for the modulated carrier is given by:
eAM (t) = (Ec + em(t))cos 2fct = (Ec + Emcos 2fmt)cos 2fct
eAM (t) = Ec(1 + mcos 2fmt) cos 2fct








![S-Parameters #5. Lossless & Reciprocal Networks Explained | Input Return Loss, S11 & Matching Basics
S-Parameters playlist.
https://www.youtube.com/watch?v p0efFhCt6I&list=PLFxhgwM1F4yyAu86pAYE5KTppq0xZ8NFr
For access to this presentation materials, membership is required: I need the Material PPT
Sent me an email to Technologies.Discussion@gmail.com
If you need the whole playlist material, send me email and we discuss.
Give me some time to response. Thanks.
A two-port network is known to have the following scattering matrix:
Determine if the network is reciprocal and lossless. If port 2 is terminated with a matched load, what is the return loss seen at port 1? If port 2 is terminated with a short circuit, what is the return loss seen at port 1?
ANS (Reciprocal)
A network is reciprocal if it is passive and contains only reciprocal materials that influence the transmitted signal. For example, attenuators, cables, splitters and combiners are all reciprocal networks, where Smn = Snm in each case, meaning the S-parameter matrix is equal to its transpose.
[S] is not symmetric, the network is not reciprocal.
A lossless network is one that does not dissipate any power. Mathematically, this is expressed as:
This means that the sum of the incident powers at all ports is equal to the sum of the outgoing (e.g., reflected) powers at all ports. This implies that the S-parameter matrix is unitary, which can be expressed as:
(S)H (S) = (I)
where (S)H is the conjugate transpose of (S) and (I) is the identity matrix. S-Parameters #5. Lossless & Reciprocal Networks Explained | Input Return Loss, S11 & Matching Basics](https://i.ytimg.com/vi/_YmHF5COg_w/mqdefault.jpg)

