The video I wish I watched before installing a SHELIX The Snekker Show 2022-06-27 | This is my second time upgrading a DeWalt DW735 thickness planer with a SHELIX cutterhead, so instead of wondering how to do it, I was more interested in how I could do it better than the last time. There's always room for improvement and usually more than one way to get the job done right, but I think this video is going to make the whole process go a little smoother for anyone doing this upgrade. It might even be fun to watch. Check the comments for updated information; I ran out of room in the video description.If this is your second time watching this and you want to move through a little faster with less jibber jabber, the chapter markers are listed below and should appear in the video's progress bar as well.You can find pictures of some of the things I build on my Instagram page.instagram.com/thesnekkershowIf you enjoyed the video and would like to see more high-quality production work, a few ways to keep the channel going include,► Watch other videos on my channel. My next video project is often influenced by how many views, likes, dislikes, comments, and subscribers a video gets.► Share the link with people who might enjoy it. If you post video links to Facebook or elsewhere, it still adds to my view count as long as you don’t download and repost the actual video.► Check out the Amazon affiliate links in the description in case there's something you need.► Use the YouTube "Super Thanks" button under the video.► Send me a tip at ko-fi.com/thesnekkershow (accepts PayPal and credit cards).► Check out my Amazon storefront:amazon.com/shop/thesnekkershow► Buy something from my Etsy shop:etsy.com/shop/thesnekkershowIn case you're wondering why I'm asking for additional support, here's what went into making this video:► The cost of the SHELIX head so I could do an installation video.► Two months without the use of my planer, workbench, or most of my workshop.► More than 115 GB of raw 4k and 8k video to make the 30 GB final product, not including at least 200 GB of takes that didn't get used.► More than 40 hours of editing time.► Video, photo, and audio editing software subscriptions.► My desktop computer is getting old, and it took three hours to export the video with the processor running up to 100% and the fan going full speed. I had to export multiple times after reviewing the output and making adjustments.► Two bags of Juan Valdez coffee beans. But seriously, if you're a coffee fan, check out juanvaldezcafestore.com (not sponsored, not affiliate, just good coffee).Stuff to get the job done:▻ SHELIX: byrdtool.com/buy-online (not sponsored)▻ Snap-ring pliers: amzn.to/3MADBEX▻ Bearing puller kit: amzn.to/3Qb67jh▻ 6mm socket: amzn.to/3xzhCd7▻ 23mm socket (3/8" drive): amzn.to/3tpjEKg▻ 23mm socket (1/2" drive): amzn.to/3N2UmZF▻ 1/2" to 3/8" socket adapter: amzn.to/3mW33dk▻ Hex key set: amzn.to/39fW0ZW▻ Torx Plus set: amzn.to/3tnZ8cU▻ Simple green: amzn.to/3QeYbOe▻ DW735X Planer (with tables and extra knives): amzn.to/2N9xSgl▻ DW735 Planer (without extension tables): amzn.to/3rKT5vL▻ Rockler 4” x 4' stretch hose: amzn.to/38VGuQ5▻ Rockler threaded disconnect fitting: amzn.to/3nW9mvu▻ 4” black corrugated snap coupler: amzn.to/3bR03uM▻ 4” hand-keyed hose clamps: amzn.to/38Vf6BvChapters00:00 Tips before you begin04:27 Cover removal06:27 OEM cutterhead disassembly10:24 Right-side disassembly16:01 Left-side disassembly21:41 OEM head removal26:42 Prepare to install the SHELIX31:59 Install the SHELIX37:34 Left-side reassembly39:32 Right-side reassembly43:36 Function checks46:14 Reinstall the inserts50:50 Test cut and troubleshooting57:14 Gratuitous planingVideo production details:▻ Video was recorded with a Samsung Galaxy S22 Ultra phone, mostly in 4k 60fps, but some was in 8k 24fps so I could record details from farther away. For the few parts where I filmed both sides simultaneously, I use a GoPro Hero 4 as the secondary camera.▻ Audio was recorded using a Rode Wireless Go and a Rode lavalier microphone.▻ I used Cyberlink Director Suite 365 for video, audio, and photo editing, and that's also where I get most of the sound clips and music tracks.▻ My editing computer is a Dell XPS 8930 with a 6-core i7 8700 processor, 32 Gb or RAM, and a GeoForce GTX 1070 video card, which is surprisingly underpowered for this type of work.Congratulations on reading all the way to the bottom. Fun fact: One of my other SHELIX-related videos resulted in Byrd Tool Experts (a distributor of Byrd Tool Corp products) contacting me for an interview, which you can see here: byrdtoolexperts.com/the-snekker-show-interview
Can a 3D Printed Tool Free a Stuck Impeller? | Harbor Freight Dust Collector Wen Impeller Upgrade The Snekker Show 2023-06-01 | In the process of swapping out my Harbor Freight dust collector's impeller for a 12" Wen version, I was met with an unyielding, stubborn impeller. After exhausting standard removal strategies and trying unsuccessfully to obtain a bearing puller through overnight delivery, I decided to make my own. The big question is: Can a 3D printed plastic part be strong enough to remove a tightly fitted impeller?Whether you're an experienced woodworker or just curious interested in innovation, you'll find this episode enlightening, showcasing the potential for 3D printing in solving workshop challenges. I used Blender software for the digital design, and a Bambu X1 Carbon for the printing.My Etsy shop is here: etsy.com/shop/thesnekkershowTools and supplies related to this video:Impeller: wenproducts.com/products/3403-022-turbo-fan-for-wen-3403Bearing puller kit: amzn.to/3Qb67jhDeWalt 20V cutoff tool (tool only): amzn.to/30DxTAbDeWalt 20V angle grinder with battery: amzn.to/3F7EtxPLENOX diamond cutting wheel: amzn.to/3mb49C8Klein CL800 clamp meter: amzn.to/3ieWwY8Klein 69409 Line Splitter: amzn.to/2N9yKBDKlein CL120 Kit: amzn.to/3bNMa02Proster Handheld Anemometer: amzn.to/3B07glyBlender software: blender.org/downloadPrinter: us.store.bambulab.com/collections/3d-printerChapters0:00 The problem1:38 The solution?4:09 First test5:38 Second test8:08 Design update10:32 Third test12:06 What broke?13:10 Now what do I do?15:46 New impeller removal and installation18:30 Conclusion#3DPrinting #HarborFreight #DustCollectionUpgrade #WorkshopHacks #Woodworking #ImpellerRemovalThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.
DeWalts New DWE625 3HP Router: Review, Comparison, and a Warning The Snekker Show 2023-03-07 | Spoiler alert: I do not recommend this router. If you're thinking about buying one, you should watch this first. If you already own one of these, you should watch this anyway to see if yours has the same issues and you just didn't notice it yet. I will post any relevant updates in the video description or the pinned comment, so check back if you're interested.For a little background, this is a review of the DeWalt DWE625 3 HP router, which is the new-and-improved version of their DW625 router that you might be used to seeing. I have owned two DW625s in the past and it's a solid performer, so when I learned that a new version was available, I was excited to try it out.This is the one I reviewed: amzn.to/3JkIcfVI DO NOT ENJOY GIVING NEGATIVE REVIEWS OF PRODUCTS. I'd rather use my time to make something cool, but I think some big companies may need a periodic reminder that consumers do not like it when reputable brands get slowly diluted.If you find this video to be helpful, please consider supporting the channel by using the YouTube "Super Thanks" button under the video, or by sending me a tip at ko-fi.com/thesnekkershow (accepts PayPal and credit cards). Some other ways to support include:My Etsy shop, growing slowly:etsy.com/shop/thesnekkershowYou can find products I like on my Amazon storefront:amazon.com/shop/thesnekkershowChapters:0:00 Introduction0:44 Model and type numbers2:30 Feature overview and comparison9:15 Noise comparison11:58 Runout measurement14:31 Depth-stop bar (FAIL)23:11 ConclusionYou can find pictures of things I build on my Instagram page.instagram.com/thesnekkershowProduction equipment:Video recording: amzn.to/3Jipu8MAudio recording: amzn.to/41TORoMEditing software: amzn.to/3SVIk8QMy computer build: amzn.to/3mmheLNThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.
Tray Routing Tips: How to Get Great Results with Minimal Sanding The Snekker Show 2023-02-13 | Template routing can be intimidating, but with the right technique and tools, it's a great way to safely and efficiently create perfect shapes and patterns in your woodworking projects. This video goes step-by-step through the process, covering everything from choosing the right router bit to setting up your jig and making your first cut. Whether you're a beginner or an experienced woodworker looking to refresh on the basics, this video is for you.If you're interested in building or buying the jig shown in this video, the plans and a limited supply of completed jigs are available on my Ko-fi and Etsy stores:thesnekkershow.etsy.comko-fi.com/thesnekkershowThese two videos are also helpful for the project:How to build the trays: youtu.be/nkuZbJNl0K0How to build the jig: youtu.be/d0HGunoGpioFind products I like on my Amazon storefront:amazon.com/shop/thesnekkershowYou can find pictures of my work on Instagram:instagram.com/thesnekkershowThese are some of the tools and supplies I use when making these trays:Whiteside bowl and tray bit: amzn.to/38LAetOWhiteside ultimate pattern bit: amzn.to/3oNdFKZWhiteside 1/8” roundover bit: amzn.to/3ikLBMDWhiteside 1/4" roundover bit: amzn.to/39Eny7EWaterlox Original Sealer/Finish Gallon: amzn.to/3E2fBZAWaterlox Original Sealer/Finish Quart: amzn.to/3HWsVjvDeWalt DW618 2 1/4 HP Router: amzn.to/39HZYqzDust Hose Adapters: amzn.to/3XGerdDDust Hose with Adapters: amzn.to/3Kkriz9Chapters:0:00 Introduction1:56 Work area overview3:28 Choose the right router bit3:56 Keep your router bit clean4:33 Use dust collection4:40 Set your depth stops7:10 Make sure the plunge lock us secure8:26 Select the proper bit speed10:58 Keep the router moving13:20 Cut in the right direction16:00 Make sure you got it all17:50 Tray-routing demonstration24:11 See the final resultThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.
Triton TRA002 3 1/4 HP Router: Initial Impressions and a Warning The Snekker Show 2022-09-13 | Spoiler alert: I do not recommend this router. If you're thinking about buying one, you should watch this first. If you already own one of these, you should watch this anyway to see if yours has the same issues and you just didn't notice it yet. I will post any relevant updates in the video description or the top comment, so check back if you're interested.For a little background, this is a review of the Triton TRA002 3 1/4 HP router, which is the new-and-improved version of their TRA001 3 1/4 HP router that you might be used to seeing. The TRA001 had good enough reviews that when I saw that the TRA002 was the upgraded version, I decided to give it a shot.I was excited about making this my new slab-flattening router, but over the past three weeks my excitement has been depleted. Despite my less-than-optimal experience, I am open to having my mind changed if new information presents itself.This is a link to the router on the Triton website:tritontools.com/en-GB/Product/Power%20Tools/Routers/TRA002The first router in this video was bought from Acme Tools.The second was bought from Woodcraft.The third was bought from Rockler.If you find this video to be helpful, please consider supporting the channel by using the YouTube "Super Thanks" button under the video, or by sending me a tip at ko-fi.com/thesnekkershow (accepts PayPal and credit cards).Find products I like on my Amazon storefront:amazon.com/shop/thesnekkershowYou can find pictures of some of the things I build on my Instagram page.instagram.com/thesnekkershowChapters00:00 Introduction01:55 Meet the TRA00205:24 Strike One14:44 Strike Two19:35 Strike Three
What is on this screw, and why did it make me hide my previous [awesome] video? The Snekker Show 2022-06-27 | It doesn't matter how long you've been working in a field, there's always something new to learn. In this short update I take a closer look at screw-thread locker, and explain how a bad assumption on my part caused a minor inconvenience with my recently upgraded thickness planer. It was easy to fix, but I had to edit and re-upload an hour-long video to hopefully prevent anyone else from making the same mistake. The updated link to that video is below.The video I wish I watched before installing a SHELIX: youtu.be/8J0rvBi8a0kFind products I like on my Amazon storefront:amazon.com/shop/thesnekkershow
Failed micro switch from a DeWalt DW735 thickness planer (correct diagnosis this time) The Snekker Show 2022-04-13 | This switch is from a DeWalt DW735 thickness planer built in 2016. The switch model is SZM-V16-FC-63, with A6605C in the top-right corner.I also have an Instagram page where I post pictures of things I build:instagram.com/thesnekkershowThis is the planer it was used in:DW735X Planer (with tables and extra knives): amzn.to/2N9xSglDW735 Planer (without extension tables): amzn.to/3rKT5vLThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use these links to make a purchase.No animals were harmed in the production of this video. The squirrel was recaptured and safely returned to the wild.
Replace the safety switch in a DeWalt DW735 thickness planer The Snekker Show 2022-04-11 | Whether you're a hobby woodworker or a professional, unexpected tool outages can ruin your day. This video shows step-by-step how to replace the safety switch in your DW735 planer.If you found this video helpful or entertaining and you'd like to help support the channel, you can send me a tip at ko-fi.com/thesnekkershow (accepts PayPal).Find products I like on my Amazon storefront:amazon.com/shop/thesnekkershowI also have an Instagram page where I post pictures of things I build:instagram.com/thesnekkershowThis is the switch: ereplacementparts.com/micro-switch-p-71324.htmlThese are some of the tools and accessories related to the video:Klein voltage tester: amzn.to/3KsRrJ9Vinyl electrical tape: amzn.to/32fX64ADW735X Planer (with tables and extra knives): amzn.to/2N9xSglDW735 Planer (without extension tables): amzn.to/3rKT5vLDW7351 Extension Tables: amzn.to/2LrYDfsThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use these links to make a purchase.
My five-year-old planer died... but I fixed it and improved it. The Snekker Show 2022-04-11 | Whether you're a hobby woodworker or a professional, unexpected tool outages can ruin your day. I tried to sneak in a little workshop time and was disappointed to find that my planer wouldn't start. After a little troubleshooting and a normal manly amount of crying, I was able to narrow down the problem, and also determine the root cause of the problem.By the end of the video, you'll know how to fix the same issue in your DW735 DeWalt thickness planer, understand why it happened, and be able to modify your planer so it never happens again. You might even find yourself entertained in the process.If you found this video helpful or entertaining and you'd like to help support the channel, you can send me a tip at ko-fi.com/thesnekkershow (accepts PayPal).Find products I like on my Amazon storefront:amazon.com/shop/thesnekkershowI also have an Instagram page where I post pictures of things I build:instagram.com/thesnekkershowThe updated switch diagnosis is here: youtu.be/o0lQ9g6YY3QThis is the switch: ereplacementparts.com/micro-switch-p-71324.htmlThese are some of the tools and accessories shown in the video:Klein voltage tester: amzn.to/3KsRrJ9Vinyl electrical tape: amzn.to/32fX64ADW735X Planer (with tables and extra knives): amzn.to/2N9xSglDW735 Planer (without extension tables): amzn.to/3rKT5vLDW7351 Extension Tables: amzn.to/2LrYDfsProcess: I filmed using a Samsung Galaxy S22 Ultra phone at 4K 60 FPS, and for certain parts, 8K at 24fps. The audio was mostly recorded using a Rode Wireless Go with a Rode lavalier microphone. The video editing was done with CyberLink PowerDirector 20 (365). The computer is a Dell XPS 8930 with a 6-core i7 8700, 32 Gb or RAM, and a GeoForce GTX 1070, and it sounded like an airplane taking off while it was processing 43 Gb of raw footage into the 6 Gb finished product.This video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use these links to make a purchase.
Does the DeWalt DW735 impeller break up shavings? The Snekker Show 2022-03-23 | In another video, I demonstrated how to remove the impeller from the DeWalt DW735 thickness planer to reduce its power draw, since a dust collection system with 4" hose makes it largely unnecessary by extracting chips and drawing cooling air past the motor. This video looks at a possible third result of using the impeller, whether by design or by chance, which is to break up wider wood shavings so they're easier for a dust collection system to handle.I have been using my planer without an impeller since around mid-2020, both with a SHELIX helical cutterhead installed and with the stock knives. I have not had any issues, and don't plan on putting it back as long as my dust collector is available.You can find pictures of my woodworking projects on Instagram:instagram.com/thesnekkershowEquipment:Rockler 4” x 4' stretch hose: amzn.to/38VGuQ5Rockler threaded disconnect fitting: amzn.to/3nW9mvuDW735X Planer (with tables and extra knives): amzn.to/2N9xSglDW735 Planer (without extension tables): amzn.to/3rKT5vLDW7351 Extension Tables: amzn.to/2LrYDfsThis video is not sponsored. I paid for everything and used my own time and materials. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.
Make a ball-bearing widget for a babys activity gate The Snekker Show 2022-03-20 | This is a remake of a video I produced in 2020, with better editing and a little more time to see what's being done in each step of the project. This addition to the activity gate was intended to help him learn about angles, gravity, obstacles, and also to help with some motor skills and upper-body strength. I made it with materials I already had on hand, which in this case conveniently included some impact-resistant polycarbonate tubing and 1/2" stainless-steel ball bearings left over from this one time when I was thinking about building a quasi-perpetual-motion machine, but then ironically lost momentum after buying the materials. The two types of wood used are purpleheart and beech.I have some other pictures and short videos of this gate posted to my Instagram page:instagram.com/thesnekkershowinstagram.com/p/CCZtvG0jcAuinstagram.com/p/CCcbSgVBK28instagram.com/p/CDMxfONhU2Cinstagram.com/p/CGW32DmjQXDinstagram.com/p/CC1mgfABch4instagram.com/p/CIwrKdEDyyISupplies:Polycarbonate tubing: amzn.to/38HOXGoStainless steel ball bearings: amzn.to/3nRwqvKThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.
Younger woodworkers! Your future self would like to have a word! #shorts The Snekker Show 2022-03-16 | When I heard that my parents were going to have this maple tree taken down, I told them that I would handle the removal so I could saw the trunk into slabs. I arrived with two 36" chains, both brand new, and one of them an Oregon ripping chain. Before I started, I commented to my brother that I remembered putting nails into some of the trees in the backyard when I was younger, but couldn't remember which ones. Now I know that this was definitely one of those trees. So, for all of the younger woodworkers out there, don't put nails in trees at your parents house. For everyone else, don't procrastinate buying a metal-detector wand. I'm going online to buy one now.
Infinity vs Whiteside for Flattening End Grain The Snekker Show 2022-02-06 | My goal was to determine which of these two high-quality router bits would provide the smoothest outcome when planing end grain, especially end grain that's prone to fuzziness and tear-out. The router-sled method is useful for flattening large wood cookies, end-grain cutting boards, log-bench ends, or anything else with a lot of end-grain surface area that might not be suitable for a thickness planer. The smoother the result from the router bit, the less time you'll spend hand-planing, scraping, and even worse, sanding.I started with the Whiteside bit, and later picked up the Infinity bit to see if it would give better results with its upshear/downshear design. I thought about including some very-low-cost bits as well just for kicks, but decided that would only degrade the overall results - The cheapest bits are cheap for a reason and aren't a good long-term value. I also thought about including some more expensive options, but this is coming out of my pocket, so we'll stick with these two for now.You can skip to the end of the video to see the conclusion, but I usually try to show how I arrived at my conclusion so that you're not just taking the word of some dude on the internet.You can find pictures of stuff that I make on Instagram:instagram.com/thesnekkershowThese are the two bits compared in this video:Whiteside 6220 Spoilboard Bit: amzn.to/38WEqamInfinity 52-506 Mega Dado & Planer Bit: amzn.to/3goSb4JThis is the router I used:DeWalt DW618 2 1/4 HP Router: amzn.to/39HZYqzIf I were to buy or test another bit, it would probably be this one:Amana RC-2250 Spoilboard Bit: amzn.to/3bPFIFXThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.
What happens when you bake wood cookies wrapped in foil? The Snekker Show 2022-02-05 | These two pieces of wood are going into the oven for several hours because I was curious what would happen, and now you're probably wondering too. I'm using white oak for this experiment, freshly cut from a dead tree. White oak has a closed-grain structure, unlike red oak which has more open pores. The closed pores make white oak more durable for outdoor projects, and for indoor projects where it might get wet, like cutting boards.Freshly cut wood generally needs one year to air dry for every inch of thickness. Baking in the oven is not a good way to dry wood faster because it will dry the surface too quickly and crack, but I was curious how quickly the wood would dry despite the cracking. End grain tends to move moisture at a much faster rate than edge grain, so I was expecting for the unwrapped piece of wood to dry out more than it did.If you want to learn more about baking wood in the oven, or sawing your own lumber, check out these two playlists:Mill your own lumber to save money and build more awesome stuffyoutube.com/playlist?list=PLvDK1rlZrs5mIO-6lVZ870LLcHVz7yW-fThermally modified wood for woodworking:youtube.com/playlist?list=PLvDK1rlZrs5lBuMYeS_umG67V5qncPPbAIf you're looking for a moisture meter, this is the one I use in the video:General pinless moisture meter: amzn.to/3hnlYvCThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.
Flattening a beautiful ambrosia maple cookie with a simple jig The Snekker Show 2022-01-19 | I found this ambrosia-maple round several years ago at the lawn-debris landfill when I was dumping a truckload of branches. One man's trash is another man's treasure. It originally measured 20" in diameter and 10" tall, and I sliced it in half with the chainsaw to make two 5" cookies (final height will be around 3.5 ").I wanted to dry them without cracking, but since they were free, I decided to take a risk and try something different. I put each cookie inside of a black trash bag and left them in the hot sun every day for a month. I'd remove the cookies each night, shake the water out of the bags, and put the cookies back in for another day. This process drew moisture out of the wood during the day, but the sealed bag prevented the wood from drying unevenly and cracking.I have no idea what I'm going to build with these other than a couple of end tables, but I had my slab flattening jig out for another project and decided to do some work on the ambrosia maple cookies at the same time. This isn't something I do frequently, so my jig has a small footprint and is easy to stick up on a shelf between uses. The next version will probably have an adjustable height, but for now, I just stack up shims underneath to get the wood to the correct height.This video would have been a lot more boring if my son hadn't popped his head into the garage to interrupt an otherwise good take of disassembling the jig. I could have filmed it again, but he inspired me retrieve some deleted clips from the recycle bin instead. And that's woodworking in a nutshell: There are very few mistakes that can't be fixed or turned into features with a little creativity, so enjoy the interruptions when you can.You can find pictures of some of my other work on Instagram:instagram.com/thesnekkershowI published a similar video almost two years ago when I started flattening the other cookie: youtu.be/NtvUmSURmGc.These are some of the tools and accessories shown in the video:DeWalt DW618 2 1/4 HP Router: amzn.to/39HZYqzWhiteside surfacing bit: amzn.to/38WEqamRockler 4” x 4' stretch hose: amzn.to/38VGuQ5RZ Mask M2.5 Bundle: amzn.to/3omb61jJohnson Paste Wax: amzn.to/3HpE4IJDust hose on router: rockler.com/dust-right-flexiport-power-tool-hose-kit-12-fixed-lengthThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.
Repairing beetle holes in flame box elder (Woodworking doesnt always go as planned) The Snekker Show 2021-12-27 | I wanted to make some beetle holes disappear from the front of a cabinet frame, but my first attempt was a little more noticeable than I wanted. The second attempt didn't look too great either. Eight attempts later, the area being patched was much bigger than when it started, but I think that the final outcome was about as good as it's going to get for this round.
How to temporarily patch a leaking washing machine front seal The Snekker Show 2021-12-24 | This video demonstrates an easy way to fix a cracked or torn front-load washing machine door boot seal, so that you can still do laundry while you wait for parts to arrive, the repairman to show up, or enough personal motivation to set in. This will work for at least a month, speaking from experience, and probably a lot longer, but you will need to replace the entire seal eventually.If this video was helpful or saved you some money, please consider sending me a tip at ko-fi.com/thesnekkershow (accepts PayPal).Find products I like on my Amazon storefront:amazon.com/shop/thesnekkershowYou can also find pictures of things that I build on Instagram:instagram.com/thesnekkershowHere are some of the supplies you'll need:Vinyl electrical tape: amzn.to/32fX64AImpact resistant super glue: amzn.to/31Tm74QSilicone spray: amzn.to/3FqmFOBThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.
How to install a mailbox lock on a wooden box The Snekker Show 2021-12-17 | Mailbox locks, also called RV locks, cylinder locks, desk and drawer locks, or cam locks, are not really designed for securing a door to a frameless body. People normally buy these to replace an existing lock, rather than for a custom build such as this one. This video demonstrates how to determine where to drill the hole, and how to modify the metal latch plate so that the door closes snugly against the box.You can fine more pictures of the things I build on Instagram: instagram.com/thesnekkershowTools and supplies used in this video include:Keyed-alike cam locks: homedepot.com/p/Prime-Products-1-1-8-in-Key-Cam-Lock-4-Pack-18-3319/308492194Fisch 7-piece forstner bit set: amzn.to/3Auy0txFreud 7-piece forstner bit set: amzn.to/3mDCpFLDeWalt 20V cutoff tool (tool only): amzn.to/30DxTAbDeWalt 20V angle grinder with battery: amzn.to/3F7EtxPLENOX diamond cutting wheel: amzn.to/3mb49C8Cordless Dremel: amzn.to/3Fn11edDremel EZ Lock diamond wheel amzn.to/3E61iAKDelta 8" grinder: amzn.to/3e3XWDGAluminum oxide grinding wheel" amzn.to/3p4jB4LRetractable fine-point marker: amzn.to/3J3mcEmThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.
Cheese and cracker serving trays - How to build the jig (Plans now available) The Snekker Show 2021-12-13 | Plans and a limited supply of completed jigs are now available on Ko-fi and Etsy:ko-fi.com/TheSnekkerShowetsy.com/shop/TheSnekkerShowBy viewer request, this video shows how to build a jig that I previously demonstrated for making cheese and cracker serving trays (see youtu.be/nkuZbJNl0K0). I produced that video two years ago and thought that the jig was pretty self-explanatory, but when I pulled it off the wall for the rebuild, I spent some time scratching my head trying to figure out what I did. Hopefully this clarifies everything and preserves the process, so that we don't need to remember all of the details.If this video was helpful, please consider sending me a tip or downloading the plans from my Ko-fi page: ko-fi.com/thesnekkershow.Find products I like on my Amazon storefront:amazon.com/shop/thesnekkershowI put pictures of the serving trays and my other projects on Instagram:instagram.com/thesnekkershowThese are the two router bits I use in this video:Whiteside bowl and tray bit: amzn.to/38LAetOWhiteside ultimate pattern bit: amzn.to/3oNdFKZTo make the trays, you will also want these two bits:Whiteside 1/8” roundover bit: amzn.to/3ikLBMDWhiteside 1/4" roundover bit: amzn.to/39Eny7EOther things you might need for this project:Impact resistant super glue: amzn.to/31Tm74QGloss polyurethane: amzn.to/3m02HCrChapters00:00 Introduction0:53 Planned improvements4:10 Make a template template15:22 Transfer to the final template19:25 Router-table kickback21:36 Make the bottom guides29:11 Add reference marks32:55 ConclusionThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.
What is Baltic-birch plywood and why should I care? The Snekker Show 2021-11-27 | I spent a large portion of my woodworking history not entirely familiar with Baltic-birch plywood, and not entirely aware of why I needed to have it in my workshop. This video is intended to quickly cover some of the most important characteristics of Baltic-birch plywood, compared with the stuff that you normally find in the big home-improvement stores.One of my primary uses of Baltic-birch plywood is building things with a mechanical use, like workshop jigs, since it's inclined to stay flat and not wear out easily, especially if any moving parts are waxed. I have also used it to make wooden gears, a baby gate, cabinet parts, knobs, wheels, etc.If you're looking for Baltic-birch plywood, your best bet is to search locally and possibly be willing to drive a little. Shipping will usually hurt. The closest supplier to me for full sheets is an hour drive one-way. I often order the 12x12-inch pieces from Woodcraft when they occasionally go on sale for a couple dollars, and use them for small projects.You can find pictures of things that I build on Instagram:instagram.com/thesnekkershowIf you like the t-shirt, here it is:Nothing beats a table saw: amzn.to/3D9m2qRThis video is not sponsored. I paid for everything, and used my own time and wit. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.
Cheap table-saw safety upgrade, and some honest talk about table-saw safety The Snekker Show 2021-11-19 | I have been making some beautiful workshop accessories lately. This is not one of them, but it's so useful that maybe I'll make version two a little more flashy.I feel pretty confident saying that most woodworkers are not nearly as safe as they should be in the workshop, and I'm one of them. I know that my tools can remove fingers and eyes, but I also know that my tools have not yet removed fingers nor eyes, so I don't lose a lot of sleep worrying about it. I've been fortunate to have had enough close calls that I know which situations are higher-risk, and therefore merit greater caution, but I don't step in to my workshop each day worried if my socks are going to melt if I touch a drill press with a faulty ground wire.Sometimes when a safety-related incident occurs, assuming the personal injury was minimal, we're more concerned about the damage to whatever project we were working on at the time. Acknowledging the reality of workshop safety, I'm providing this video to give you a very inexpensive and not-at-all-inconvenient way of improving your safety around one of the most dangerous tools in the workshop: The table saw.Please note that I am not advocating irresponsible behavior or a disregard for workshop safety; I'm just being honest about what I've seen and what I've done. I'm a firm believer that it's better to be safe than sorry, but I'm not always a practicing believer.In case you need a hot glue gun:DeWalt glue gun: amzn.to/3qYLHjcGorilla dual-temp mini glue gun: amzn.to/3wXWdIIDeWalt dual-temp (the one used in the video): homedepot.com/p/DEWALT-Ceramic-Rapid-Heat-Dual-Temperature-Full-Size-Glue-Gun-DWHT75098This video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.
I made a nice box for my finger-joint blades The Snekker Show 2021-11-17 | This was kind of a distraction project, but I really like my new Forrest finger-joint blades, and they didn’t come with a storage case. Sometimes you just gotta treat yourself to nice things. The body is made from some incredibly hard reclaimed oak; the bottom panel is ash; the top includes maple, cherry, chestnut oak, beech, and purpleheart; the spacers are hickory; and the wheel is wenge. The hinges are solid brass, and the bolt and nut are stainless steel. It’s finished with several coats of Waterlox, and buffed with wax to a silky-smooth finish.You can find more pictures of this box, and other things that I build, on my Instagram account: instagram.com/thesnekkershowSome of the supplies used are listed here:White 3M pads: amzn.to/3kJVINsJohnson Paste Wax: amzn.to/3HpE4IJWaterlox Original Sealer/Finish Gallon: amzn.to/3CNLwdwWaterlox Original Sealer/Finish Quart: amzn.to/39uTL16StopLossBags 4 Pack: amzn.to/2ZpatNMTitebond III wood glue: amzn.to/3ssN0VVDeWalt 1-3/4 HP router kit: amzn.to/3iXgUzDDeWalt DW618 2 1/4 HP Router: amzn.to/39HZYqzWhiteside ultimate pattern bit: amzn.to/3oNdFKZWhiteside bowl and tray bit: amzn.to/38LAetOWhiteside 1/8” roundover bit: amzn.to/3ikLBMDFisch 7-piece forstner bit set: amzn.to/3Auy0txThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.
I tried something different with miter joints. What do you think? The Snekker Show 2021-11-11 | This isn't the first time I've rounded over the inside edges of a miter joint, but it is probably the first time that I've done it intentionally, and without swearing immediately after. These frames are going to be used as doors on some suggestion boxes, and I wanted to add some additional detail without detracting from the already pleasing combination of purpleheart and beech. The whole process probably added two or three hours to the project, including testing the cut, extra sanding, extra caution when gluing, and some extra work when finishing, but since I'm doing this project for fun, I'm happy to trade some time for a unique outcome.The finished product can be seen on my Instagram account: instagram.com/p/CYaGLrNLuWGIf you're going to try this, make sure you have a sharp and clean bit. This is the router bit I used in the video:Whiteside 1/8” roundover bit: amzn.to/3ikLBMDThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase
Greenworks GPW3000 Electric Pressure Washer Review The Snekker Show 2021-11-11 | My old, discounted, reconditioned, gas-powered pressure washer died several years ago, and I picked up a Greenworks 2000 PSI electric one as an inexpensive replacement. After many hours of pressure washing a one-inch-wide path, I realized that was a mistake. I gifted the 2000-PSI one to my parents for light work around the house, and upgraded to a Greenworks 3000 PSI model, which is one of the most-powerful electric pressure washers available for use on a 15-amp circuit. In this video I answer the question of whether this electric pressure washer is a satisfactory option for pressure-washing concrete around the house. In short, yes, it is, but you should still watch the entire video to see some troubleshooting and also a stray cat named Eclipse.If I helped you make a smart purchase decision, please consider sending me a tip at ko-fi.com/thesnekkershow (accepts PayPal).I can't find it on Amazon, so here's a link to the pressure washer on the company's website:greenworkstools.com/pro-3000-psi-brushless-pressure-washer-gpw3000This is the 15" attachment shown in the video:lowes.com/pd/Greenworks-3100-PSI-Rotating-Surface-Cleaner-for-Electric-Pressure-Washers/1002550790This is the Karcher 15" attachment I've heard recommended:amzn.to/3GqRouRTo reduce the time I spend pressure washing in the future, I have sealed everything with Siloxa-Tek 8505, which is an obscenely expensive, but so far an extremely good sealant: amzn.to/3H8Lik7This video is not sponsored. I paid for everything and used my own time, and a stray cat. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.
Thickness planer modification that I should have done a long time ago The Snekker Show 2021-10-31 | Woodworkers and tool manufacturers have been trying to mistake-proof the trade for the entirety of human existence, but it seems like every project brings some new lesson, or even an old lesson that you didn't learn anything from. I'm a big fan of my DeWalt DW735 thickness planer, but there are a few things that I would like to improve. One thing in particular has made me a little cranky on more than one occasion, so today I decided to fix it.You can find pictures of my woodworking projects on Instagram:instagram.com/thesnekkershowSupplies:Wooden wheel (1)3/8" Nylon washers (2)3/8" Stainless steel washers (Depending on wheel thickness)Mod Podge (for finishing the wheel): amzn.to/3oUA0X2Equipment:Rockler 4” x 4' stretch hose: amzn.to/38VGuQ5Rockler threaded disconnect fitting: amzn.to/3nW9mvuDW735X Planer (with tables and extra knives): amzn.to/2N9xSglDW735 Planer (without extension tables): amzn.to/3rKT5vLDW7351 Extension Tables: amzn.to/2LrYDfsThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.
Forrest Finger Joint Set - Unboxing, Testing, and Review The Snekker Show 2021-10-25 | I picked up a Forrest finger joint set to accompany the new finger-joint jig that I'm building, and this video shows the blade in action cutting a variety of woods, both with and across the grain. You'll also see comparative cuts with a Freud 6" Super Dado. I feature the Forrest FJ08242 in this video, but it would apply equally to the FJ08241 and FJ08243 sets. The FJ08241 does 3/16" and 5/16" wide cuts, the FJ08242 does 1/4" and 3/8", and the FJ08243 does all four.This video is not sponsored. I paid for everything, and used my own time. You can find Forrest blades at forrestblades.com/. Pro tip: If you use Microsoft Edge as your browser, you might get a prompt at the top of the browser window if another website offers a lower price on the item you're viewing.This isn't a Forrest vs. Freud video, because I would need two identically-purposed blades for that, but since the Forrest finger-joint and Freud dado blades used in the video are both high-quality, and perform similar functions, I use them to compare the differences between the two types of wide-kerf blade-set choices. It goes without saying that the results might have been different if I was using different brands. If you have some additional experience to share, leave a comment.You can find pictures of things that I build on Instagram:instagram.com/thesnekkershowFor anyone wondering about the chipped tooth shown on the Forrest blade, I contacted the company, and they quickly sent me a warranty replacement. It's always nice to see an outstanding product backed by an outstanding warranty.There are pros and cons to the various wide-kerf blade choices, and these are some of my opinions:* Flat-grind finger-joint set *Pros:- Costs about the same as a 10" sawblade, but you get two blades.- You get two (or four) width configurations with one kit.- Flat grind does not leave scoring marks on your finished project.Cons:- No scoring cutters could potentially cause tear-out in cross-grain cuts.- More expensive than router bits.- If you need a wider cut, multiple passes are needed.* Dado stack *Pros:- Can be configured for a variety of material widths.- Scoring cutters can reduce tear-out in certain materials.- Only one pass required unless you need to go wider than the blade's limit.Cons:- Can take more effort to set up, especially if shims are needed.- Scoring cutters can leave visible machine marks on your finished project.- Chipper blades usually have fewer teeth, which can cause tear-out.- More expensive than router bits.* Regular #1 flat-grind sawblade *Pros:- Cuts narrow corner splines in a single pass, or wider grooves with multiple passes.- In some cases, can be less expensive than a wide-kerf set.- Normally can function as a regular ripping blade.- Flat grind is less prone to blade flutter than alternate top bevel (ATB).Cons:- If you need to cut wide kerfs, you need to make a lot of passes.- High-quality blades might cost the same as a wide-kerf set.- More expensive than router bits.* Router bit *Pros:- Inexpensive compared to a new sawblade.- Cuts the same width each time.- More expensive spiral-cut bits can make a very clean cut.Cons:- Sharpening reduces the diameter slightly.- Cutting to the side can shift workpieces if not secured.- Tear-out can happen on the side of the joint, which can be harder to hide.* Handsaw and chisel *Pros:- Satisfying- Bragging rights- Distraction from lifeCons:- Takes foreverChapters:0:00 Introduction4:05 Unwrapping and comparison8:21 End cut test11:12 Edge cut test14:14 Test results25:50 Conclusion
Easy dowel joinery for dissimilar parts without buying a jig The Snekker Show 2021-10-10 | Dowel joinery doesn't need to be complicated or expensive; you just need some scrap wood. This video covers a few simple shop tips that saved me some time and improved the outcome of a small project step stool I'm building for my son.I'll put pictures of the final product on Instagram, once the finish is cured: instagram.com/thesnekkershowTools and supplies:Whiteside 2580 flush trim bit: amzn.to/3lsSMWfFisch 7-piece Forstner bit set: amzn.to/3Auy0txFreud 7-piece Forstner bit set: amzn.to/3mDCpFLThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.Chapters00:00 Introduction01:24 Make routing templates04:25 Make dowel jigs08:09 Dry fitting the parts
How to prevent finishes from going bad in the can - Eliminate the can The Snekker Show 2021-09-26 | I use Waterlox for most of my woodworking projects, but because of its cost and tendency to gel in the can, I'm usually reluctant to break the seal unless I have several things to finish at the same time. This is a bit of a nuisance, because I have to figure out where to safely store my almost-done projects until I'm ready for a batch finishing job.You can save money and make finishes last longer by transferring larger containers to smaller ones, adding filler material like pieces of plastic to the can, or displacing the oxygenated air with Bloxygen or propane. Now, I'm giving Stop Loss Bags a shot, because the concept seems fundamentally sound. Full cans are effective at preserving finishes because they contain more finish than air. As the space occupied by liquid decreases, the space occupied by air increases. Chemical-resistant bags allow you to reduce the container size to match the remaining volume of liquid, so there's no air to displace.If this video was helpful or saved you a can of expensive finish, please consider sending me a tip at ko-fi.com/thesnekkershow (accepts PayPal).StopLossBags 4 Pack: amzn.to/2ZpatNMStopLossBags Funnel: amzn.to/2Y1EuTBWaterlox Original Gallon: amzn.to/3CNLwdwYou can find pictures of my woodworking projects on Instagram: instagram.com/thesnekkershowThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.
Sawing an ugly box elder log to find hidden treasure The Snekker Show 2021-09-08 | I got my hands on some box elder logs from an unhealthy tree that was going to come down eventually. Fortunately, that's the best kind of box elder for woodworkers. In this video, I'll saw open some ugly firewood-sized logs on the bandsaw to reveal some beautifully figured and colored flame-figured wood.The first project I made with this wood, after drying and testing the stability, was a banana holder. I top-coated with satin polyurethane, but strengthened the wood first by thinning some epoxy 50% with alcohol and letting it soak in. That was probably an unnecessary step, but it's an option if you even think a piece of wood is too soft.Here are a few links for more information about box elder:wood-database.com/box-elderen.wikipedia.org/wiki/Box_ElderThis is the moisture meter I used: amzn.to/3hnlYvCYou can buy Pentacryl here: preservation-solutions.com/product/pentacrylHere are some more pictures of the banana hanger: instagram.com/p/CTLIIv1LDXEYou can see pictures of other things I've built on Instagram:instagram.com/thesnekkershowThis video is not sponsored. I paid for everything, and used my own time.
Harbor Freight 2HP Dust Collector Air Flow Measurements The Snekker Show 2021-08-21 | I've been asked several times about the air flow on my modified two-stage Harbor Freight dust collection system with a Thien baffle and Wynn Environmental filter, so I picked up an inexpensive anemometer to see if I can finally give an accurate answer. In this video, I measure several different parts of the system, and show how the meter is set up for each one. If I made any mistakes in the process, let me know in the comments and I'll make the corrections here in the video description.CORRECTIONS: At 2:05, I meant one square foot, not one cubic foot. You measure the square footage of the opening to measure how many cubic feet of air is passing through. Of course, I said this right before joking about my math skills, and then proceeded to add a graphic to the video that matched my spoken mistake. I also misspoke the decimal point a couple times, even though it was showing correctly on the meter (zero point seven one, instead of point zero seven one). Central Machinery 2Hp Dust Collector: harborfreight.com/2-hp-industrial-5-micron-dust-collector-97869.htmlYou can buy Wynn filters at wynnenv.com/woodworking-filters/. The current (2021) model number for the filter I put in my system is 35C222NANO. They also make a 35B222NANO, which is the same thing but with a removable top cap.Proster Handheld Anemometer: amzn.to/3B07glyRockler 4” x 4' stretch hose: amzn.to/38VGuQ5Skywalker 14' trampoline (for cardboard): amzn.to/3z7I5N5Chapters0:00 Introduction1:26 Explaining the process4:15 How to set up the anemometer6:08 End of hose, dirty filter6:49 Cleaning the filter9:29 End of hose, clean filter10:12 Y-splitter11:13 Under the impeller15:10 Cardboard ductThe old videos showing how I built the system are at this playlist:youtube.com/watch?v=QJd8WwIlwMM&list=PLvDK1rlZrs5m-dggAgJO_EwbYr6Px5bfxThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.
Ants killed the tree. Ill keep the lumber. The Snekker Show 2021-07-07 | This white oak tree came down after years of being eaten by ants and other borers. It would make good firewood, but it will make even nicer lumber. White oak is very weather resistant, and once it's cut and dried I can use it for outdoor projects. If I dry it in a kiln to eliminate the bugs, it will make some nice indoor projects too.Ants really seem to enjoy oak wood, and it seems like every year I'm losing another tree, including red oak, white oak, and chestnut oak. I'm trying to manage the ant population, but as indicated from the inside of this stump, a lot of my trees have been dead for years and just haven't admitted it yet.Some of the materials used or mentioned in this video are listed below.Anchorseal: amzn.to/2LyELXYAnchorseal 2: amzn.to/2LP3M0LGeneral pinless moisture meter: amzn.to/3hnlYvC24" Granberg mill: amzn.to/3xlGZwA (The one I have)30" Granberg mill: amzn.to/3jOQzUF36" Granberg mill: amzn.to/3jMzdrp (The one I wish I had)This video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.Granberg website: granberg.comStihl chainsaw: stihlusa.com/products/chain-saws/professional-saws/ms661cm
Large picture frames with splined corners (fast version) The Snekker Show 2021-06-23 | The full 30-minute version of this video can be found at youtu.be/ZcUfu4j34uA, with more tips and details about the project, and maybe even a few attempts at humor. Sometimes it's more fun to just watch progress in fast-forward.These frames are built with hard maple, and feature purpleheart splines in the corner for strength and style. Picture frames aren't very difficult to make, but there are a lot of small details that can change the outcome. I've made plenty of picture frames throughout the years, and it always seems to take longer than it should because of the time required to calibrate power tools, build or set up jigs, and verify that each angle and measurement is exactly as it should be. This was one of my smoothest builds yet, mostly thanks to some extra time spent making a better spline jig for the table saw.Tools and supplies:Whiteside 3/4" 1084 straight bit: amzn.to/3wQTNKQWhiteside ultimate pattern bit: amzn.to/3oNdFKZFreud Chamfer Bit: amzn.to/35y2VYODeWalt 1-3/4 HP router kit: amzn.to/3iXgUzDSelf-Centering Drill Bit: amzn.to/3wGqr1J2' Universal T-Track: amzn.to/3gApZwz4' Universal T-Track: amzn.to/2SBpZmXQuick Release Band Clamp: amzn.to/3vIuAAVTurn Buttons: amzn.to/3wGFzfwKeyhole hangers: amzn.to/3q6fQL8Satin water-based polyurethane: amzn.to/3iT46tJFuji Mini-Mite 4 PLATINUM sprayer: amzn.to/3gIYlxDFuji Q4 PLATINUM sprayer: amzn.to/3wHmbiBThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use these links to make a purchase.
How to make large picture frames with splined corners The Snekker Show 2021-06-18 | These frames are built with hard maple, and feature purpleheart splines in the corner for strength and style. Picture frames aren't very difficult to make, but there are a lot of small details that can change the outcome. I've made plenty of picture frames throughout the years, and it always seems to take longer than it should because of the time required to calibrate power tools, build or set up jigs, and verify that each angle and measurement is exactly as it should be. This was one of my smoothest builds yet, mostly thanks to some extra time spent making a better spline jig for the table saw.Tools and supplies:Whiteside 3/4" 1084 straight bit: amzn.to/3wQTNKQWhiteside ultimate pattern bit: amzn.to/3oNdFKZFreud Chamfer Bit: amzn.to/35y2VYODeWalt 1-3/4 HP router kit: amzn.to/3iXgUzDSelf-Centering Drill Bit: amzn.to/3wGqr1J2' Universal T-Track: amzn.to/3gApZwz4' Universal T-Track: amzn.to/2SBpZmXQuick Release Band Clamp: amzn.to/3vIuAAVTurn Buttons: amzn.to/3wGFzfwKeyhole hangers: amzn.to/3q6fQL8Satin water-based polyurethane: amzn.to/3iT46tJFuji Mini-Mite 4 PLATINUM: amzn.to/3gIYlxDFuji Q4 PLATINUM: amzn.to/3wHmbiBChapters:0:00 Design0:50 Wood preparation3:28 Cutting miters on the table saw5:20 Rabbets and edge details8:02 Clamping and gluing11:35 Corner splines18:17 Keyhole hangers and turn buttons21:44 Sanding and finishing24:46 Final detailsThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use these links to make a purchase.
How to trim corner splines with a router The Snekker Show 2021-04-11 | There are a lot of ways to trim corner splines, but a sharp bit in the router table probably gives the fastest and cleanest results, assuming you pay attention to grain direction.You can find more picture of these frames, and other things I build, on Instagram.instagram.com/thesnekkershowWhiteside ultimate pattern bit: amzn.to/3oNdFKZI'm using a Porter Cable 7518 3 1/4 HP router motor, but I recently learned that Porter Cable has stopped making routers, so that is no longer available.The lift is an INCRA Mast-R-Lift II.This video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use these links to make a purchase.
Drill Powered Crawl Space Caddy - Part 2 The Snekker Show 2021-03-28 | I need to do some work under the house that will either involve a large amount of effort and physical discomfort, or a medium amount of effort and physical discomfort and some fun time inventing things in the workshop. I opted for the second option. This video covers the background information about what I'm building and why, and will likely be part of a series eventually culminating in a full build video. No promises on that last part, since I never know when life is going to kick me right in the plans.I tried to make this informative and entertaining, and spent a little more time than usual in production. The whole video took four weekends to make, used 40 GB of video, and took my 6-core processor to 100% capacity. If you found it entertaining or useful, please share the link around to help keep the channel alive.More pictures are on Instagram: instagram.com/thesnekkershowIn case this gives you any ideas and you decide to build your own contraption, some of the parts I used are linked below. This isn't a complete parts list, and doesn't come with instructions or diagrams beyond what's shown in the video and Instagram photos. No sense in doing a build video until I get the final design figured out.ToolsDeWalt 20V cordless drill: amzn.to/38JqMa7DeWalt 60V cordless joist drill: amzn.to/3eFJdQH3/8″ socket adapter: amzn.to/3rts3IT3/8" tilt socket adapter: amzn.to/3w92DE75/8" extended socket: amzn.to/3tYTLPmCorentium Airthings Radon Detector: amzn.to/3w92zUEWheels10" pneumatic wheels: amzn.to/3cusP3Y10" flat-free wheels: amzn.to/3daFhW0Bearings3/8" bearings: amzn.to/39ousOP5/8" bearings: amzn.to/2Pc3CCABolts, washers, nuts5/8 x 6" hex bolts: amzn.to/3lVL0ms5/8" x 5" hex bolts: amzn.to/3wh6vTA5/8" flat washer: amzn.to/3fnodyC5/8" nylon lock nuts: amzn.to/2QAHmmf3/8" x 3 1/2" bolts: amzn.to/39lQMZE3/8" x 4" full-thread bolts: amzn.to/3dhMxzl3/8" flat washers: amzn.to/3rqs4gR3/8" hex nuts: amzn.to/3w4VYe33/8" nylon lock nuts: amzn.to/2PyHKRO3/8" tee nuts: amzn.to/3sweBp23/8" coupling nut: amzn.to/3csAgsEOther parts and supplies5/8" OD 3/8" ID nylon tubing: amzn.to/39nA7VhChapters:00:00 Introduction03:16 What inspired this project7:36 Water management basics8:18 Crawl space encapsulation12:08 What's been done, and what remains15:35 Thinking through labor-reduction solutions17:03 Requirements for the new solution19:08 Demonstrating and testing the prototypeIf you want to make wooden gears, woodgears.ca is the site I used to print my gear templates.This video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use the Amazon links to make a purchase.
Samsung Galaxy S21 Ultra video resolution comparison (8K, 4K, 1080p, 720p) The Snekker Show 2021-03-18 | This video is not about woodworking, but relates to the equipment I use to produce content for the channel. I demonstrate different video resolutions filmed with a Samsung Galaxy S21 Ultra cellphone, and demonstrate why higher resolutions are desirable when you're trying to future-proof your memories, show greater detail, or film a broader area so you can zoom in later. This is not an extremely technical video, and is mostly intended to show some visible differences that the average phone videographer like me might care about.I kept the frame rates comparable for the video, but the phone does 1080p and 4K at 60 frames per second, and 8k at 24 frames per second. The audio is not from the cellphone, it's from a Rode Wireless Go and Rode lavalier microphone. If you want a Rode Wireless Go, shop around for prices.Samsung Galaxy S21 Ultra: amzn.to/38QDjZrRode Wireless Go: amzn.to/38T4p1XThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use these links to make a purchase.
Drill Powered Crawl Space Caddy Part 1 The Snekker Show 2021-03-16 | This is just a quick preview of a drill-powered device I've been working on little by little in my free time. I'll get in to greater detail about its purpose and features in subsequent videos as I continue to refine the design, and probably do a full build vehicle for the final version. If you're the type of person who enjoys building jigs and mechanical devices, keep an eye on the channel for updates.I'm using a very old DeWalt 18V drill in this video with a nickel cadmium battery. The final version might use a 60v drill:DeWalt 60V cordless joist drill: amzn.to/3eFJdQHDeWalt 60V mixing drill: amzn.to/38IWHYkThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use these links to make a purchase.
Replace a circuit breaker, learn how it works, and overload the old one The Snekker Show 2021-02-16 | This video is all about having some fun while learning stuff. Learn how thermal circuit breakers work, then see how to bypass the thermal breaker in a space heater, then see how to replace the breaker in this thickness planer, then watch me take apart the old breaker, and finally see what happens when I overload the disassembled breaker with almost 40 amps.If this video was helpful or saved you the expense of a service-center repair, please consider sending me a tip at ko-fi.com/thesnekkershow (accepts PayPal).The thickness-planer circuit breaker can become increasingly sensitive to heavy workloads after tripping several times, and replacing the breaker is the best option at that point. This is an easy procedure that can be completed in ten minutes with some basic tools and an inexpensive part. Save yourself some money and two trips to the service center and do it yourself.You can also find me on Instagram: instagram.com/thesnekkershowKey items featured in the video:Circuit Breaker Part 5140000-19: amzn.to/3jWjCndDW735X Planer (with tables and extra knives): amzn.to/2N9xSglDW735 Planer (without extension tables): amzn.to/3rKT5vLKlein CL800 clamp meter: amzn.to/3ieWwY8This video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use these links to make a purchase.Chapters00:00 Introduction01:48 Thermal breakers and bi-metal strips03:22 Space heater safety switch05:02 How to replace a DW735 circuit breaker11:25 Disassembling the DW735 circuit breaker14:20 First look inside the breaker19:08 Overload test introduction21:11 Inside view of a breaker trip23:57 Gratuitous slow motion 24:27 What's next on The Snekker Show?You might have noticed that there are no ads in the middle of my videos. I have the option to turn that off, so I turn it off to let you watch the video uninterrupted.
How to replace the circuit breaker in a DeWalt DW735 thickness planer The Snekker Show 2021-02-16 | This is a basic tutorial showing how to replace the circuit breaker in a DeWalt DW735 or DW735X thickness planer. The breaker can become increasingly sensitive to heavy workloads after tripping several times, and replacing the breaker is the best option at that point. This is an easy procedure that can be completed in ten minutes with some basic tools and an inexpensive part. Save yourself some money and two trips to the service center and do it yourself.If this video was helpful and saved you from paying for an expensive repair, please consider sending me a tip at ko-fi.com/thesnekkershow (accepts PayPal).If you want to see a cooler version of this video, including disassembling and overloading the circuit breaker in slow motion, use this link: youtu.be/24f-J0lVo-E.You can also find me on Instagram: instagram.com/thesnekkershowKey items featured in the video:Circuit Breaker Part 5140000-19: amzn.to/3jWjCndDW735X Planer (with tables and extra knives): amzn.to/2N9xSglDW735 Planer (without extension tables): amzn.to/3rKT5vLKlein CL800 clamp meter: amzn.to/3ieWwY8This video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use these links to make a purchase.
Miter Saw Dust Hood from Cardboard (Part 2 of 2) The Snekker Show 2021-02-01 | This is version 2 of the cardboard miter-saw dust box, and I think it's a 99% solution. For background, I pulled my miter saw away from the wall to do some cleaning and maintenance, and decided to upgrade the dust collection at the same time. It would be ideal to just install perfect dust collection for the entire workshop all in one shot, but I think for most of us it's a life-long process of gradual upgrades. This is a prototype, so I didn't see any reason to commit to a wooden structure just yet. Cardboard is free, easy to work with, and would last for many years.If this video was helpful, please consider sending me a tip at ko-fi.com/thesnekkershow (accepts PayPal).I also post pictures of things I build on Instagram.instagram.com/thesnekkershowThese are some of the materials I used, excluding the TV:Rockler 2-1/2" stretch hose: amzn.to/3akvSJY4” black corrugated snap coupler: amzn.to/3bR03uM100mm Dust Shoe Brush: amzn.to/3crlOS7100mm Dust Shoe Brush (2 pack): amzn.to/3rd9rgnThis is the 4" stuff that was already on my dust collector:Rockler 4” stretch hose: amzn.to/38VGuQ5Rockler threaded disconnect fitting: amzn.to/3nW9mvu4” hand-keyed hose clamps: amzn.to/38Vf6Bv
Four simple ways to modify an RZ mask for improved fit and seal The Snekker Show 2021-01-25 | After wearing both of my RZ masks periodically over a couple months, I really didn't like the way either one fit, so I decided to improve the design. Watch me demonstrate four different ways you can modify the M2 or M2.5 masks for a better fit and seal. I put links below to some of the materials you might need, depending on which approach you select.These modifications range from extremely easy and free, to reasonably easy and inexpensive. I recommend trying one of the temporary approaches before committing to something permanent. This is a long video because I thought it might help some people to see the whole process of sewing the modifications, but it's broken in to chapters for easier viewing.This is the original unboxing-and-review:youtu.be/oRJudVFLezkMasks:RZ Mask M2 Bundle: amzn.to/3a5CiwbRZ Mask M2.5 Bundle: amzn.to/3omb61jSupplies:Compact Sewing Kit: amzn.to/3ce5ROW1/4" Made-in-USA Black Elastic: amzn.to/39hqeJl1/2" Made-in-USA Black Elastic: amzn.to/3qW4N6B1/2" Curved Side Release Buckles: amzn.to/3qQfIP13/8" buckles: amzn.to/3pmlIyH (I ordered some of these after producing the video and confirmed they are the same size as, and compatible with, the buckles that came on the mask)This video is not sponsored. As an Amazon Associate I earn from qualifying purchases.Chapters:00:00 Introduction1:16 M2.5 - Easy strap relocation option5:06 M2.5 - Easy strap replacement option10:05 Explanation of how M2.5 straps are sewn on12:49 M2.5 - Strap relocation option (involves sewing)33:00 M2 - Adding a strap (involves sewing)47:43 - Conclusion
Miter Saw Dust Hood from Cardboard (Part 1 of 2) The Snekker Show 2021-01-03 | I pulled my miter saw away from the wall to do some cleaning and maintenance, and decided to upgrade the dust collection at the same time. It would be ideal to just install perfect dust collection for the entire workshop all in one shot, but I think for most of us it's a life-long process of gradual upgrades. This is just a prototype, so I didn't see the point in committing to a wooden structure just yet. Cardboard is free, easy to work with, and would last for many years. I'll post a follow-up later once I finalize the design.This was filmed in 4K 60FPS, so you can see in great detail where the dust is going as I'm doing each set of cuts. What would you do to improve the design?I also post pictures of things I build on Instagram.instagram.com/thesnekkershowPart 2 of this video is here: youtu.be/m6bQcDboL-8
Laguna 14BX 220V bandsaw three-week and three-year reviews The Snekker Show 2020-12-16 | I recorded this three years ago shortly after buying this bandsaw, and never got around to processing and publishing the video. It's not my finest video-production work, but the information is good. I added a three-year follow up to the end, and the timeline is chaptered so you can jump ahead to anything that catches your interest.You can also find me on Instagram:instagram.com/thesnekkershowThis video is not sponsored. As an Amazon Associate I earn from qualifying purchases.Laguna 14BX: amzn.to/35JSnq2Chapters:0:00 Overall satisfaction, power, and performance1:29 Throat plate flatness, and Laguna customer service2:27 Blade tracking and tension lever3:21 Blade and fence alignment, and fence opinions7:36 Measurement scale8:38 Foot brake use and adjustment10:08 Making blades coplanar13:02 Blade-cleaning brush in lower cabinet15:04 Table adjustment17:04 Blade tension adjustment18:52 Guide blocks21:04 Blade-guard adjustment22:15 Dust collection24:23 Test cut on purpleheart26:40 Three years later
Using a drill and auger bit to excavate for a sump pump basin The Snekker Show 2020-12-15 | This is not a sump-pump installation tutorial, this is just a demonstration of how an auger bit could be used to make digging in a confined space easier.The auger bit is from powerplanter.com/. They advertise "100% designed, manufactured, and distributed in the USA" on their site. I bought the Extended Length Bulb Auger, 3" x 24", with 1/2" Hex Drive. I ordered directly from the manufacturer with free shipping, and it arrived promptly. This is not a sponsored video, but the product and service were good enough they deserve recognition.You can find pictures of my less-dirty work on Instagram:instagram.com/thesnekkershow
Laguna Bandsaw Dust Collection The Snekker Show 2020-12-14 | This is a short overview of the dust collection setup for the back of my Laguna 14BX 2.5HP 220V bandsaw. This video is not sponsored. Part names and some links are below:For the bandsaw:(1) 4 in. PVC Sewer and Drain 90° Hub x Hub Elbow(2) 4 in. PVC Sewer and Drain 45° Hub x Hub Elbow(1) 4 in. PVC Sewer and Drain 45° Hub x Hub x Hub Wye(2) 4-in x 4-in x 4-in dia x 4-in L Flexible Repair Coupling(1) 4 in. PVC Sewer and Drain Pipe, cut to 3 3/4", 10 1/4", and 7 1/4"For the dust-collection hose:Rockler 4" threaded disconnect fitting: amzn.to/35JEg4hRockler 4” x 2' stretch hose: amzn.to/3bDOXsHRockler 4” x 4' stretch hose: amzn.to/38VGuQ5The bandsaw itself:Laguna 14BX: amzn.to/35JSnq2As an Amazon Associate I earn from qualifying purchases.You can also find me on Instagram.instagram.com/thesnekkershow
More planer power testing (Answering viewer questions) The Snekker Show 2020-12-07 | This is a quick and simple no-load power-draw measurement using two clamp meters and two line splitters to respond to questions about the accuracy of the previous measurements or the decimal placement. As a bonus, you'll learn how to make a simple line splitter.DW735X Planer (with tables and extra knives): amzn.to/2N9xSglDW735 Planer (without extension tables): amzn.to/3rKT5vLDW7351 Extension Tables: amzn.to/2LrYDfsKlein CL800 clamp meter: amzn.to/3ieWwY8Klein 69409 Line Splitter: amzn.to/2N9yKBDKlein CL120 Kit: amzn.to/3bNMa02(This video is not sponsored. As an Amazon Associate I earn from qualifying purchases.)Other related videos:Replace a DW735 circuit breaker, learn how it works, and see the inside as it gets overloaded: youtu.be/24f-J0lVo-EWhat happens when you remove the impeller from the planer?youtu.be/UoBN5Sc_2ukShelix vs. straight knife power comparison with 110mm (4 3/8") ash board (ROUGH VIDEO)youtu.be/z-5n9ElTp2sThe video I wish I watched before buying a Shelix (video version 2)youtu.be/47PyY4K47KU
RZ Mask M2 and M2.5 unboxing, comparison, and review The Snekker Show 2020-12-06 | I've been looking at these for a while with some skepticism, and finally decided to answer my own questions. I wasn't sure which style to buy, so I picked up one of each for a comparison. In this video I open the box, give my first impressions, try them both on, and then follow up after spending a little time wearing each one.I made a follow-up to this video showing how to improve both of these masks for a better fit and seal. youtu.be/qW9oGrBMoJQYou can also find pictures of things I make on Instagram:instagram.com/thesnekkershowThese are the masks I demonstrated:RZ Mask M2: amzn.to/3a5CiwbRZ Mask M2.5: amzn.to/3omb61jThis video is not sponsored. As an Amazon Associate I earn from qualifying purchases.
My simple, no measure, pizza crust recipe The Snekker Show 2020-11-24 | Too many people go through their entire lives lacking the confidence or knowledge needed to make a good pizza. If your crust recipe is hit-or-miss, this video might help you hit the mark a little more consistently. If I come up with any significant updates I'll post it here in the description, but my intent is to keep this simple.I also post photos of stuff I make on Instagram. Mostly wooden things, but also the occasional pizza. Maybe one day I'll make a wooden pizza.instagram.com/thesnekkershowThis is the pizza stone I use: amzn.to/3iWoUyxThis is the KitchenAid mixer: amzn.to/3oLgdZX(This video is not sponsored. As an Amazon Associate I earn from qualifying purchases.)Chapters00:00 Introduction1:24 Ingredients3:00 Mixing11:18 The right look and feel12:20 Let it rise15:39 Forming the crust23:19 Adding toppings27:54 Baking29:26 Out of the oven
What is a filter, and why do we wear masks? The Snekker Show 2020-11-17 | I imagine this year has been frustrating for a lot of people as they try to figure out what's true, what's opinion, what's a mistake, and what's intentionally misleading. This is just my attempt at clearing up a few points of confusion for some people, hopefully without starting a silly political argument. If you choose to wear a mask to protect yourself, or to protect others, or if you're not sure whether you should, my intent is to just help clear things up.
What happens when you remove the impeller from the planer? The Snekker Show 2020-11-08 | The DW735 thickness planer comes with an impeller for removing chips, but I always run my planer connected to a dust collection system. I started to wonder if the impeller was even necessary at that point, or if it was just robbing energy from the cutterhead, so I removed the impeller for a test. At the time of this video, I'd been using it without the impeller for several months to make sure it wasn't going to cause any issues with dust buildup or overheating. As of 2022, I have not noticed any issues related to removing the impeller.If this video was helpful, please consider sending me a tip at ko-fi.com/thesnekkershow (accepts PayPal).I also post pictures on Instagram: instagram.com/thesnekkershowThe planer shows in this video has a Byrd Shelix cutterhead installed, which increases the power draw. You can find more information here: youtu.be/47PyY4K47KU?t=1007In another video, I show how to replace a DW735 circuit breaker, explain how it works, and cut it open so you can see the inside as it gets overloaded: youtu.be/24f-J0lVo-EDW735X Planer (with tables and extra knives): amzn.to/2N9xSglDW735 Planer (without extension tables): amzn.to/3rKT5vLDW7351 Extension Tables: amzn.to/2LrYDfsKlein CL800 clamp meter: amzn.to/3ieWwY8Klein 69409 Line Splitter: amzn.to/2N9yKBDKlein CL120 Kit: amzn.to/3bNMa02Rockler 4” x 2' stretch hose: amzn.to/3bDOXsHRockler 4” x 4' stretch hose: amzn.to/38VGuQ5Rockler threaded disconnect fitting: amzn.to/3nW9mvuThis video is not sponsored. I paid for everything and used my own time. As an Amazon Associate, I may earn a small commission if you use these links to make a purchase.
