80/20: R40 Center Guide (R40-CGUIDE) @8020llc

Uploaded April 2024 | Updated September 2026, 2 weeks ago

To Purchase: bit.ly/3xwPWIr
Find in Catalog: bit.ly/428g7iZ
80/20 Website: bit.ly/3peM7n3

Sold at 96" (2.438 meter)

80/20: 550mm Task Light with Dimmer (21055)

80/20: 10 Series Double Slide-in Economy T-Nut (3280)

80/20: 40 Series Anchor Fastener (40-3362)

$80/20: Leveling Caster Overview To Purchase: https://bit.ly/45CqTAd Find in Catalog: https://bit.ly/428g7iZ 80/20 Website: https://bit.ly/3peM7n3 Hello and welcome to 80/20’s product highlight series. Today we’re going to take a look at the leveling caster. This caster is great for applications that require level surfaces, but also may need to move from time to time. It’s available in fractional and metric, and across a wide range of profile series. This caster can be installed on the end of a profile, or on the side of it. Regardless on how you decide to mount it, a bolt assembly and a base plate will be required. More information on 80/20’s recommended bolt assemblies can be found in the 80/20 product catalog. Now for our example, we decided to mount it on the side of the profile. We’ve already got our base plate mounted on there. So we’re going to take our caster, flip it upside down and we’ll line up the holes on the caster, with the ones on the base plate. From there, we’ll take our bolts, and thread them in there one by one. Now once we have those tightened down. The great feature about this caster, is that when you need it to move, you can use the wheel on the back and when you need a level surface, you just adjust the caster to lower the leveling foot, and you have your leveling foot. Now hopefully you found this segment on leveling caster helpful. For more information please visit 80/20.net and make sure to subscribe to future 80/20 videos. And as always, make it a great day.$

$80/20: Double Anchor Fastener Overview To Purchase: https://bit.ly/3OZWeGT Find in Catalog: https://bit.ly/428g7iZ 80/20 Website: https://bit.ly/3peM7n3 Hello, and welcome to 80/20s product highlight series. Today were going to take a look at the double anchor fastener. What makes the double anchor fastener so popular is its unmatched strength. Its available in fractional, metric, and is compatible across a wide range of profile series. The double anchor fastener comes in five parts; you have two cams, two bolts, and a double T-nut. Now one thing youll want to keep in mind when using the double anchor fastener; youll need a counterbore service in two sides of your bar. More information on the counterbore service can be found in the 80/20 product catalog. Now when it comes to installing the double anchor fastener, youre going to start with your bolts. Take your bolts, put them into your cams. At that point, youre going to take your bar with the counterbore machined into it, and place the cams into the counterbores. Next, grab your double T-nut. Place it on the end of the bolts, take your wrench and slightly engage the T-nuts into the threads. At that point we are ready for our other bar. Were going to slide the double anchor fastener into the bar, and find our desired location. At that point, take your T-wrench, and tighten down firmly. Now the great thing about the double anchor fastener is its adjustability. If you need a new location on the bar, simply loosen up the double anchor fastener, and slide it anywhere along the bar. Once you found your new location, tighten down, and youre good to go. At this point, we have a strong, secure, vibration-proof connection, good for any load-bearing application. Now hopefully you have found this segment on the double anchor fastener helpful. For more information, visit 8020.net and make sure to subscribe to future 80/20 videos. And as always, make it a great day.$ $80/20: Panel Gasket Overview To Purchase: https://bit.ly/43DwZ1n Find in Catalog: https://bit.ly/428g7iZ 80/20 Website: https://bit.ly/3peM7n3 Hello and welcome to 80/20’s product highlight series. Today we’re going to take a look at panel gasket. It helps fill the gap between panel and t-slot, cutting down on noise and vibration. It’s easy to install and available in both fractional and metric. Now when it comes to installing panel gasket, you’re just going to need your clippers. So we’ll move our frame here, get it into place, and we’ll grab our panel gasket, we’ve already got it cut to length, now I’m just going to cut it at a 45 degree angle and what that’s going to do is allow our panel gasket pieces to meet in the corner nice and flush. We’ll just start by placing it right into the open T-slot between the panel and the bar itself. Just slightly push down and work your way across, and once I’m done with that, I’m going to repeat the process all the way around the frame. Now you’re only going to need to do this on one side, and once you are done with that, it should cut down on a lot of noise and vibration in your panel. Now hopefully you found this segment on panel gasket helpful. For more information please visit 80/20.net and make sure to subscribe to future 80/20 videos. And as always, make it a great day.$

80/20: 10 Series 1/4-20 x .750 Black BHSCS & Standard Slide-In T-Nut (3479)

$80/20: Roller Wheel Overview 80/20: Roller Wheel Overview 80/20 Website: https://bit.ly/3peM7n3 Find in Catalog: https://bit.ly/428g7iZ Hello and welcome to 80/20’s product highlight series. Today we’ll be taking a look at roller wheels. These wheels allow profiles to easily roll along the T-slot of adjoining profiles. They are easy to install, available in both fractional and metric, and compatible across a wide range of profile series. Now the great thing about using these wheels, is they require no machining, and they come preassembled. Now when it comes to installing these wheels, you have two choices. You can install it with or without a bracket. If you are going to do it without a bracket, simply take the wheel and loosen up the T-nut, and you’ll slide it into the open T-slot. You’ll find your location, and then you’ll tighten it down. Now if you’re going to use a bracket you simply take the preassembled part, and loosen up the T-nuts. From there, you’ll slide it into the open T-slot, you’ll find your location you want, and you’ll tighten down the bolts as well. From there you’ll take your mating profile, and as you can see you’ll have nice smooth movement, thanks to these roller wheels. Now hopefully you found this segment of roller wheels helpful. For more information, please visit 8020.net, and make sure to subscribe to future 80/20 videos. And as always, make it a great day.$