Uploaded May 2026 | Updated November 2026, 1 day ago
Build a motor start-stop-jog control panel in the free ACC PLC Simulator โ Start on X1, Stop on X2, Jog on X3, motor on Y1 with a run light. Watch it run, free.
โก QUICK ANSWER
The control-panel scene in the free ACC PLC Simulator gives you a classic motor control panel to program: an enclosure with three pushbuttons driving a motor. In the example, the green Start button is wired to X1 as a normally open input, the red Stop button is wired to X2 as a normally closed input, and a Jog button is wired to X3. The output Y1 drives the motor, with a Run pilot light to show when it is running. That is the foundational start-stop-jog circuit that nearly every PLC beginner learns. Pressing Start energizes the motor and a seal-in rung latches it on, the normally closed Stop button drops it out when pressed, and the Jog button runs the motor only while it is held. The reason to build it in the simulator is that you can write the ladder logic and watch the panel respond in real time, in your browser, with no install and no hardware. Press the buttons in the 3D scene and see the motor and pilot light react to your logic. It is one of the best first programs to write because it teaches latching, normally closed stop wiring, and momentary jog control all at once. The full walkthrough is in the guide below.
๐ง THE CONTROL-PANEL SCENE WIRING
โถ Enclosure with three pushbuttons driving a motor
โถ START (green) wired to X1 โ normally open
โถ STOP (red) wired to X2 โ normally closed
โถ JOG wired to X3
โถ Y1 drives the MOTOR, with a Run pilot light
๐ก WHAT YOU BUILD
โถ Start latches the motor on (a seal-in rung)
โถ The normally closed Stop drops it out when pressed
โถ Jog runs the motor only while the button is held
โถ Write the logic and watch the 3D panel respond โ no install, no hardware
๐ฎ TRY IT FREE โ THE ACC PLC SIMULATOR
accautomation.ca/simulator
(Browser-based, no install โ press the buttons and watch your logic run the motor)
๐ FULL WRITTEN TUTORIAL โ CONTROL-PANEL SCENE
accautomation.ca/how-to-use-the-acc-plc-simulator-control-panel-scene-tutorial
๐ WHAT YOU'LL LEARN
โ The control-panel scene's wiring: Start X1, Stop X2, Jog X3, motor Y1
โ How a seal-in rung latches the motor on from a momentary Start
โ Why the Stop button is wired normally closed
โ How Jog runs the motor only while it's held
โ How to build it and watch it run in the free browser simulator
โ FREQUENTLY ASKED
Q: What is the control-panel scene in the ACC PLC Simulator?
A: A free browser-based 3D scene with a three-pushbutton motor control panel โ Start on X1, Stop on X2, Jog on X3, and the motor on Y1 with a run light โ that you program with ladder logic and watch respond. Try it using the link above.
Q: Why is the Stop button wired normally closed?
A: So the motor stops safely if the button or its wiring ever fails โ a broken wire looks the same as a press and drops the motor out. It's the standard, safe way to wire a stop. The full walkthrough is in the guide.
๐ Try it free: accautomation.ca/simulator
๐ MORE RESOURCES
โถ Getting started with the control-panel scene: youtube.com/shorts/nxcTQUdZ7vk
โถ Control-panel scene written guide: accautomation.ca/how-to-use-the-acc-plc-simulator-control-panel-scene-tutorial
โถ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
โถ Free eBooks: accautomation.ca (subscribe for download)
๐ฌ Questions? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #PLCSimulator #MotorControl #StartStop #LearnPLC #Shorts
Regards,
Garry
ACC Automation
accautomation.ca
Build a motor start-stop-jog control panel in the free ACC PLC Simulator โ Start on X1, Stop on X2, Jog on X3, motor on Y1 with a run light. Watch it run, free.
โก QUICK ANSWER
The control-panel scene in the free ACC PLC Simulator gives you a classic motor control panel to program: an enclosure with three pushbuttons driving a motor. In the example, the green Start button is wired to X1 as a normally open input, the red Stop button is wired to X2 as a normally closed input, and a Jog button is wired to X3. The output Y1 drives the motor, with a Run pilot light to show when it is running. That is the foundational start-stop-jog circuit that nearly every PLC beginner learns. Pressing Start energizes the motor and a seal-in rung latches it on, the normally closed Stop button drops it out when pressed, and the Jog button runs the motor only while it is held. The reason to build it in the simulator is that you can write the ladder logic and watch the panel respond in real time, in your browser, with no install and no hardware. Press the buttons in the 3D scene and see the motor and pilot light react to your logic. It is one of the best first programs to write because it teaches latching, normally closed stop wiring, and momentary jog control all at once. The full walkthrough is in the guide below.
๐ง THE CONTROL-PANEL SCENE WIRING
โถ Enclosure with three pushbuttons driving a motor
โถ START (green) wired to X1 โ normally open
โถ STOP (red) wired to X2 โ normally closed
โถ JOG wired to X3
โถ Y1 drives the MOTOR, with a Run pilot light
๐ก WHAT YOU BUILD
โถ Start latches the motor on (a seal-in rung)
โถ The normally closed Stop drops it out when pressed
โถ Jog runs the motor only while the button is held
โถ Write the logic and watch the 3D panel respond โ no install, no hardware
๐ฎ TRY IT FREE โ THE ACC PLC SIMULATOR
accautomation.ca/simulator
(Browser-based, no install โ press the buttons and watch your logic run the motor)
๐ FULL WRITTEN TUTORIAL โ CONTROL-PANEL SCENE
accautomation.ca/how-to-use-the-acc-plc-simulator-control-panel-scene-tutorial
๐ WHAT YOU'LL LEARN
โ The control-panel scene's wiring: Start X1, Stop X2, Jog X3, motor Y1
โ How a seal-in rung latches the motor on from a momentary Start
โ Why the Stop button is wired normally closed
โ How Jog runs the motor only while it's held
โ How to build it and watch it run in the free browser simulator
โ FREQUENTLY ASKED
Q: What is the control-panel scene in the ACC PLC Simulator?
A: A free browser-based 3D scene with a three-pushbutton motor control panel โ Start on X1, Stop on X2, Jog on X3, and the motor on Y1 with a run light โ that you program with ladder logic and watch respond. Try it using the link above.
Q: Why is the Stop button wired normally closed?
A: So the motor stops safely if the button or its wiring ever fails โ a broken wire looks the same as a press and drops the motor out. It's the standard, safe way to wire a stop. The full walkthrough is in the guide.
๐ Try it free: accautomation.ca/simulator
๐ MORE RESOURCES
โถ Getting started with the control-panel scene: youtube.com/shorts/nxcTQUdZ7vk
โถ Control-panel scene written guide: accautomation.ca/how-to-use-the-acc-plc-simulator-control-panel-scene-tutorial
โถ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
โถ Free eBooks: accautomation.ca (subscribe for download)
๐ฌ Questions? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #PLCSimulator #MotorControl #StartStop #LearnPLC #Shorts
Regards,
Garry
ACC Automation
accautomation.ca










