Fine tuning my setup to find the center of this 2-inch piece U Do It 2026-09-27 | Fine tuning my setup to find the center of this 2-inch piece
UDoIt Reviews Furniture - Bon Augure Rustic Oak Bookshelf U Do It 2024-04-16 | In this UDoIt Reviews video, I review the Bon Augure Rustic Oak Bookshelf. This is a very stylish rustic piece with a subtle modern touch. The manufacturer sent this to U Do It™️ for review.But Why a Bookshelf?You may ask "Why would a DIYer review a bookshelf?"UDoIt is a lifestyle brand with many facets including clothing design, interior decoration, and more. UDoIt takes an idea to paper and completes the build with style in mind. However, the word completes is highly exaggerated because there are several unfinished projects. The struggle is real.BON AUGURE Rustic Oak Bookshelf: amzn.to/3vVEwgJTo learn more about this product as well as other products visit U Do It™️ here: udoit.me/udoit-reviews-bon-augure-rustic-oak-bookshelf“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records LLC All Rights Reserved. No Cheese Records® is a Registered Trademark of No Cheese Records LLC All Rights Reserved.
How do you anchor a shed? With American Earth Anchors of Course U Do It 2024-03-29 | My first question in our latest windstorm was "How do you anchor a shed?" I did some research on how to tie down a shed. And, I determined for my shed that this would be best with American Earth Anchors. American Earth Anchors offer an 18-inch Penetrator anchor earth screw made of solid aluminum with a 1-inch hex head for installation with a torque wrench. This Penetrator anchor has an impressive strength rating of 2,500 lbs. I'm always curious about product specifications. I'm confident that four of these with one installed in each corner would hold our shed in a heavy wind storm. If all forces were equal then that would be almost 10,000 lbs of holding strength. Since wind gusts come in many different directions, this is probably derated. But, it is still an impressive number.Tools and Products used in this video:Penetrator 18 inch Aluminum Screw Earth Anchor: amzn.to/4cBXZDOTie Off for PE-18: amzn.to/3IYRDANRidgid 18V 1/2 inch High Torque Impact Wrench: amzn.to/4cLS92ORidgid 18V Cordless Drill and Impact Driver Kit: amzn.to/3x99ZMCRed Sharpie: amzn.to/3vzm4KHStanley FatMax 35-foot Tape Measure: amzn.to/3VDkNgjSAE Deep Impact Socket Set: amzn.to/43zAZ4dLexivon Impact Socket Adapter Set: amzn.to/4cxUEpf1/2 inch x 3 1/2 inch Stainless Steel Lag Bolts: amzn.to/3xfAaBw1/2 inch Stainless Steel Fender Washers: amzn.to/3TwjwF8To learn more about this product installation as well as other products visit U Do It™️ here: udoit.me/do-it-yourself-build-a-shed-how-do-you-anchor-a-shedVideo Chapters0:00 Anchoring the Shed Introduction1:15 Installing the anchor on the first corner2:02 Determining where to secure the tie-down3:05 Drilling pilot hole for stainless steel lag bolt3:42 Securing tie-down to shed with lag bolt5:50 Checking if siding corner will fit over it6:30 The lag bolt and fender washers6:50 Review of impact driver and PE-18 Anchor7:39 Installation of the anchor on 2nd corner10:50 Installation of anchor on 3rd corner13:36 Installation of anchor on 4th corner15:38 Installation of vinyl siding corner over the anchor point15:58 Review of tools used17:25 Why am I anchoring my shed? For future wiring“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records LLC All Rights Reserved. No Cheese Records® is a Registered Trademark of No Cheese Records LLC All Rights Reserved.
UDoIt Video Gear - The best camera angle for maximum impact U Do It 2024-03-24 | If you want your content to have the best camera angle for maximum impact then you'll find this UDoIt™️ Video Gear video helpful. I'm using the Neewer 9.8-inch adjustable magic arm with a super clamp. It is also known as an articulating arm. I recently reviewed a hedge trimmer (video will be released soon) and I strive for the best POV (point of view) for the viewer. I show you just how I did that.Usually, when editing my videos I am saddened that I wasn't more intentional in my camera angles. Sometimes I get in the way of the camera. Other times the camera is too far away. I called an audible 3/4 of the way through recording my hedge trimmer review. I decided to use a camera angle held in place with the articulating arm that I just purchased.Watching a hedge trimmer in action from afar is useful to an extent. But, what if I brought the viewer close to the blade cutting the foliage? That's exactly what I do in this video. The Neewer articulating arm is capable of holding 4.4 lbs fully extended. I'm using the GoPro Hero 10 Black camera and it is nowhere close to 4.4 lbs so we're good. The articulating arm includes a super clamp, which allows you to securely clamp to a round or square tube. The super clamp has foam pads that enhance its gripping strength, and as you can see it grips well.The Neewer 9.8-inch Adjustable Magic Arm and Super Clamp is available here: amzn.to/3J88UYtTo learn more about the Neewer Adjustable Magic Arm and Super Clamp used in this video as well as other tips and tricks visit U Do It™️ here: udoit.me/the-best-camera-angle-for-maximum-impact“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records LLC All Rights Reserved.
UDoIt Reviews the Biusine cordless chainsaw kit U Do It 2024-03-20 | In this video, UDoIt Reviews the Biusine cordless chainsaw kit. The saw features a 14-inch blade and includes two 21V 6Ahr batteries, a charger with a European plug adapter, two 14-inch chains, a user guide, and a tool for installing and removing the chain. The user guide does not provide a lot of help for assembly. I try not to read the user guide, anyway. However, for those who are using a chainsaw for the first time, my video will provide more help than the supplied user guide.Please note that this is for demonstration purposes only. You are responsible for your own safety and safe operation. Please refer to the included safety instructions. Safety is a mindset and should be applied all the time.The battery charger supplied with my unit came with a European-style plug. The manufacturer indicated that this should not be the case when ordered. I have similar units, which use the same 21V batteries. I was able to use the charger for these batteries. Please note, that this is against the recommendation within the user guide. So please only use the battery charger supplied with the unit. If your unit did not come complete with the correct charger adapter, contact the manufacturer and they will supply you with the correct adapter.When I initially assembled the chainsaw, I had difficulty installing the cover. I eventually learned that it was due to the tensioner (barrel nut) that was not in the correct position. Inspecting the area where the wood chips are ejected, you can observe the tensioner and its relative position to the receiving hole within the bar. Once lined up it clicks into place with moderate force as demonstrated. You can attach the flanged nuts to hold the cover in place but you need to properly set the tension before torquing them down. Setting the tension of the chain is easy through a quick observation. As the chainsaw is resting level on your work surface, verify that the chain is not sagging in the middle of the bar. It should be very close to the bar. However, if you lightly tug on the chain of the underside of the bar and pull it you should notice a little slack in the chain. This is expected. So, adjust the tension accordingly. Please note that a chain that has high tension will exert excessive force on the sprocket and motor shaft. This can result in excessive wear to the motor, electronics, and the sprocket at the end of the bar. And too loose of a chain can result in the chain flying off the bar.Once your tension is set correctly, you can fill the reservoir with bar and chain oil. In the video, I use Toro bar and chain oil. Use the brand of oil you are happiest with but appropriate for a 14-inch chainsaw. Secure the oil cap in place and install the battery. You are now ready to begin cutting away.I began cutting but not really. The saw wasn't digging into the wood. It was at that moment that I realized the chain was installed backward. It was an oversight I had during the installation. The teeth of the chain on the top of the bar must point away from the saw. The teeth dig into the wood and chip away at it. If the chain is installed backward, it will not dig into the wood. And if you continue to operate the saw in this manner for an extended time it can damage the saw. The Biusine 14-inch cordless chainsaw is available here: amzn.to/3Tri1bmToro Bar and Chain Oil: amzn.to/4cpRKTiFor my detailed review as well as other tool reviews please visit U Do It™️ here: udoit.me/tool-review-biusine-14-inch-cordless-chainsaw-kit“As an Amazon Associate I earn from qualifying purchases.”Video Chapters: 0:00 Unboxing of Biusine Cordless Chainsaw Kit1:30 Assembly of chainsaw2:53 Installation of bar and chain4:44 Installation of chain cover and tensioning of chain6:21 Adding bar and chain oil7:10 Attempt to cut but unit fails9:03 Manufacturer sent a replacement saw9:42 Assembly of new saw11:56 Cutting a lot of wood cookies15:20 My review of the saw and final thoughtsVideo Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records LLC All Rights Reserved.
Do you know where your nuts are? U Do It 2024-03-12 | In this video, you will learn how to improve your workshop flow by labeling things. There's nothing worse than interrupting your flow to find the nuts and bolts you need for your project. Only to spend more time looking for them than doing the real work. We all know about labeling. But, did we label things? For the most part, I know where things are in my shop. But, I have several Ridgid Tools small parts organizers that I stack very high. They aren't labeled and when I find one I often don't put them back in the same order. I know I have one that is dedicated to 1/4-20 nuts, bolts, and washers. However, trying to find it can sometimes require me removing each one only to find it was the bottom one. If they are labeled, I might have to remove each one to get to the bottom one. But, at least I'll know instantly where it is in the stack.The Brother P-Touch Cube compatible label cartridges manufacturer sent me these labels for review. I figured this was a better time than ever to start my labeling. This brings back memories of when I would help my dad label things with the Dymo label maker. He too had a workshop that was organized with small parts drawers, pickle jars hanging from the ceiling, and racks of baby food jars.Hehua Brother P-Touch Cube TZe-231 Label Cartidge 6-Pack White: amzn.to/3V9n5ndBrother P-Touch Cube Label Maker: amzn.to/3TeGVKZTo learn more about my labeling process as well as projects visit U Do It™️ here: udoit.me/storage-and-organization-improve-your-flow-by-labeling“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
Dont toss it - Repurposing a fluorescent lamp and save money U Do It 2024-03-09 | In this video, I show you how to save money by repurposing a fluorescent lamp by using parts from a broken one.Our friend Blaise gave me two fluorescent lighting fixtures. One was broken and had an electrical cord with a 3-prong plug. The other was a salvaged lighting fixture permanently installed in an office and professionally removed by an electrician. Blaise needs me to remove the electrical cord from the broken one and install it within the other fixture. He will then use LED drop-in replacement bulbs to help reduce energy costs.In my article, I go into the details of how I removed the cord from the broken one. Then I safely installed the new lighting fixture. This was easily achieved using a Romex connector, a spade crimp connector, two crimp cap connectors, and electrical tape.If you want to learn more about this retrofit and learn about other ways to save money visit U Do It™️ here: udoit.me/save-money-by-repurposing-lighting-fixturesTools and Materials Used in this Video:Cap Terminal Crimp Connectors - amzn.to/3uUV6grElectrical Tape - amzn.to/49K9xD6Fluorescent Bulbs3/8 inch Romex Connector - amzn.to/3PcKhwWDiagonal CuttersNeedle Nose PliersWire StrippersFlat Head ScrewdriverDigital Multi MeterVideo Chapters0:00 How to Save Money by Repurposing a Fluorescent Lamp0:20 Removing the electrical cord from the bad one2:41 Inspecting the good Fluorescent Lamp4:05 Installation of Romex Connector5:13 Installation of Electrical Cord6:04 Connecting Ground to Metal Housing6:57 Attaching Hot and Neutral Wires9:48 Assembly of the lamp and power-up11:29 An example of how we save money“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
GOYOJO GW192S SuperIR Thermal Imaging Camera Review U Do It 2024-03-07 | If you are interested in thermal imaging applications then the GOYOJO GW192S SuperIR Thermal Imaging Camera may be your solution. The camera features a 192x192 resolution and a temperature range of -4 to 1022 degrees Fahrenheit. A button is on the front of the handle, which can be used for image capture to the built-in memory on the camera. But, it can also be used to turn on the laser pointer. There is a menu option to disable the laser, as you would not want that on if you are scanning people or pets. You can transfer the images from the camera using the included USB-C to USB-A data transfer and charging cable.The GOYOJO GW192S Thermal Imaging Camera is available here: amzn.to/434BXoQTo learn more about this camera and see other tool reviews and projects visit U Do It™️ here: udoit.me/tool-review-goyojo-gw192s-thermal-imaging-cameraThe camera's menu has many options, some of which are important to optimize temperature readings. These important options include the Units, Emissivity, Distance, and Temperature Range. Units allow you to select F, C, or K temperature scales.Emissivity is a setting used to match the object being scanned. There are several emissivity preset choices, including brick, soil, and human skin. But, if you can't find the item you can enter a custom emissivity value.Distance is how far the item being scanned is from the thermal camera. As you may know light decreases exponentially the further away you are from the source. This setting helps to compensate for that.Temperature Range is the setting for the range. You can select Auto Switch, -4 to 302 degrees Fahrenheit, or 212 to 1022 degrees Fahrenheit. I found that Auto Switch will provide you with the appropriate temperature range but it takes some time to switch. Selecting the temperature range manually is probably the better choice. It will let you know when you exceed the range as shown in the video.Video Chapters0:00 Unboxing of the GOYOJO GW192S SuperIR Thermal Imaging Camera0:35 Initial power-up and first look at the camera features3:11 Using the camera to inspect my electric heater5:35 Changing the temperature range6:25 Switching between color gradient modes8:55 Recording a social media video with the camera11:06 Detailed review of the camera settings12:53 Setting the Emissivity parameter14:55 Setting the Distance parameter16:55 Setting the Color Palette (color gradient)17:46 Display Setting allows control over what shows on the display18:13 Level & Span Settings19:10 Setting the Temperature Units and Date & TimeThe manufacturer sent this unit to U Do It for review. “As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records® LLC All Rights Reserved.
Easy Fix for Compressor not Building Pressure OL195 Pump U Do It 2024-02-23 | If your compressor is not building pressure it could be because of a faulty valve plate or piston ring. Of course, there could be other reasons, but this is what I found in my case. In this video, I show you how I diagnose my Husky pancake compressor problems and fix them. The compressor pump on this unit is model number OL195. It is used in some Husky, Stanley, and Bostitch models and possibly others. The model number is clearly imprinted on the pump for easy identification.Many oil-less air compressor pumps are built with a motor that spins a flywheel, which has a connecting rod and piston assembly that pushes air through a cylinder. This compressed air feeds into a valve plate and pump head. This assembly supplies air into the compressor through a check valve, which prevents the compressor from losing air through the pump head. The compressor pump is controlled by a pressure switch with built-in hysteresis. The hysteresis could be set for 25 psi with a max pressure of 125 psi. This would mean that the pump will kick on at 100 psi and turn off around 125 psi. But, what if the pump never shuts off? That's why compressors are supplied with pressure relief valves to trip at a higher pressure, like 150 psi. The particular problem with my pump is that it builds up pressure to around 45 psi but doesn't exceed it. The compressor doesn't lose pressure, which means that the check valve is ok and all hoses beyond the check valve are good. The problem could be within my pump itself. Another problem is that the pump never shuts off since it isn't achieving the maximum pressure of 125 psi. This could result in damage to the pump and motor and could possibly create a fire hazard from overheating.Now that I built a shed, I'm cleaning up my garage and moving stuff into the shed. After rediscovering this old compressor that I had sitting I remembered that I had intentions of fixing it. That's why we are here. I have since purchased a replacement compressor that performs much better. But, it's nice to have this old one as a spare. And I enjoy restoring equipment that can be fixed without spending too much money.The parts diagram for your compressor and pump is almost surely available online. The OL195 diagram is available on several websites where you can order replacement parts. The model OL195 pump on my compressor was assembled using the single valve plate. I upgraded to the double valve plate, which also required replacing the connecting rod cap for the piston. The double valve plate kit part number is AB-9429999. You may also see model information such as Bostitch CAP60P-OF, which uses the OL195 pump.The piston ring is available here: amzn.to/3wx9b3OThe valve plate assembly and cap are available here: amzn.to/3UKAP7LTo learn more about this repair as well as other repairs and projects visit U Do It™️ here: udoit.me/equipment-repair-husky-air-compressor-is-not-pressurizingTools Used in the RepairBall-End Allen Bits: amzn.to/48reDCEMilwaukee Shockwave Impact Driver Bit Set: amzn.to/3wyEwmILoctite Threadlocker Blue 242: amzn.to/3T7EACVCraftsman Mechanics Tool Set: amzn.to/3Iaz38gRidgid Drill and Driver: amzn.to/3UNqR5qC-Clamp: amzn.to/49L2j1m“As an Amazon Associate I earn from qualifying purchases.”Video Chapters0:00 My Air Compressor Will Not Pressurize2:10 Evaluating the problem3:40 Removing the head body to inspect valve plate5:45 Valve plate has a broken valve6:43 Replacing the single valve plate with double valve plate12:00 Preparing to install new piston ring14:04 Removing fan (reverse threads)14:40 Removing connecting rod from flywheel bearing15:18 Installing piston ring on connecting rod15:55 Installing piston into piston cylinder and installing connecting rod onto bearing16:49 Installing double valve plate and pump head17:37 Installing fan onto flywheel (reverse threads)18:25 Compressor now reaches 125 psiVideo Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records LLC All Rights Reserved.
How to build a shed ramp U Do It 2024-02-06 | In this video, you'll learn how to build a shed ramp using 2x8 lumber and pressure-treated plywood.This is a shed that I started construction at the beginning of 2023. I finally have the shell up with a roof and I require easy access to it. A ramp built out of pressure-treated wood is a quick way to achieve this. I have extra 2x8 lumber left over from when I was repairing our deck, extra Simpson Strong-Tie fasteners, and Zmax joist hangers. All that was needed was the purchase of another 3/4 inch sheet of pressure-treated plywood.U Do It™️ Recommended Tools for Building a Shed: amzn.to/3H0AEgkThe details of the construction as well as other projects on U Do It™️ here: udoit.me/do-it-yourself-build-a-shed-how-to-build-a-rampVideo Chapters:0:00 Cutting the ramp joists3:44 Discussion of construction5:00 Attaching 3rd ramp joists to shed floor joists7:13 Simpson Strong-Tie ZMax Joist Hangers9:38 Using Simpson Strong-Tie 2 1/2" Construction Screws12:03 Attaching last ramp joist13:52 Installing blocking between ramp joists14:58 Installing plywood for ramp15:48 Credits“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
DIY Cantilevered Shelving Brackets for Storing Lightweight Materials U Do It 2024-01-27 | In this video, we'll demonstrate how to build DIY Cantilevered Shelving Brackets using scrap wood and rebar.I'm building a shed and it might be some time until it is complete. I'm storing the materials, such as J-Channel and vinyl soffits on the floor in the shed. But, I need this floor space to store things that are currently taking up room in my garage. And, this material is in danger of becoming damaged as it sits on the floor.I have scrap pieces of 2x4 lumber and leftover pieces of rebar that I used for staking out the perimeter of the shed. The only thing I need to do is fabricate the shelf brackets and hang them. Then, of course, move the building material from the floor to the brackets.A curated list of products of potential storage units as well as the tools and materials that can be used to build the brackets are available here: amzn.to/48OQgzITo learn more about how I built the Catilevered Shelving Brackets or discover other project ideas and solutions visit U Do It™️ here: udoit.me/diy-cantilevered-shelving-brackets0:00 My plan to build a Cantilevered Shelf Bracket1:58 Drilling a half-inch hole into the wood4:40 Hammering rebar into wood7:40 Installation of the shelf brackets9:56 Loading the shelf with the building materials11:31 SPAX PowerLag Wood Screws11:57 Summary video for social media13:00 Credits“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records LLC All Rights Reserved.#garageorganization #storagesolutions #storagespace
Review of CKLT Log Grabber Tongs for your Firepit or Fireplace U Do It 2024-01-25 | In this video, I review the CKLT Log Grabber Tongs to manage the fire in your firepit or fireplace. This log grabber is made of stainless steel, has rubber handles, and features sharp teeth for digging into the logs you are picking up. The tongs have the precision to pick up the smallest piece of bark while having the strength to pick up the largest log. They allow you to manage your fire at a safe distance from the flames.To learn more about this product and other products and projects visit U Do It™️ here: udoit.me/tool-review-log-grabber-for-your-firepit-or-fireplaceTo purchase this product visit U Do It™️ Firepit and Fireplace Essentials list here: amzn.to/429XtYQThe wood used in this fire was cut with the IMOULIVE Mini Chainsaw shown in this video here: youtu.be/Vqq0eERLHLY“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records® LLC All Rights Reserved.
Oneida Air Systems Dust Deputy 2.5 Cyclone Separator Review U Do It 2024-01-19 | I unbox the Oneida Air Systems Dust Deputy 2.5 Cyclone Separator Deluxe Kit. This is a complete kit and is ready to use with your vacuum if it has a 2.5-inch hose. Oneida was kind enough to send me a unit for evaluation. I chose not to install the casters for my test. However, the kit comes with feet, casters and a strap that you can connect to your vacuum. This strap will keep the Dust Deputy 2.5 in follow mode with your vacuum.The video focuses on the unboxing of the cyclone, the lid and gasket, the bucket, and the hose. I am currently building a setup that will house the Dust Deputy and my vacuum in one cabinet with casters.You can find the Oneida Air Systems Dust Deputy 2.5 Deluxe Separator Kit on U Do It™️ Woodworking Essentials list here: amzn.to/3Sm9pn0To learn more about this product and other products and projects visit U Do It™️ here: udoit.me/oneida-air-systems-dust-deputyVideo Chapters0:00 Unboxing of Oneida Air Systems Dust Deputy 2.51:30 Assembly of the cyclone lid3:50 Assembly of the Dust Deputy 2.5 and connecting to my Ridgid vacuum5:00 Setup of epic camera angle with my GoPro and Neewer RGB61 light6:25 Vacuuming with the Dust Deputy 2.5 8:11 Inspection of the Ridgid Vacuum 10:00 Observing what was collected by the Dust Deputy10:40 Credits“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese RecordsⓇ LLC All Rights Reserved.
This mini chainsaw helped me clean up after a storm U Do It 2024-01-15 | In this tool review, we unbox and demonstrate the ImoumLive 6-inch Mini Chainsaw for Pruning and tree trimming. The manufacturer sent this product to me for review.The product was nicely housed within a latched blow mold case. Included in the case were safety glasses, a maintenance kit, a battery charger with two 21V 3Ahr batteries, and the operating manual.The saw feels strong compared to other mini chainsaws I have reviewed. It has some weight to it and feels like the material used for the housing is dense and strong. Nearly everything was self-explanatory but considering safety I thought it was important to review the manual. The manual helped me understand some of the features. However, the manual did not describe the maintenance kit that was supplied. For instance, it was not clear if the included bottle of liquid was chain and bar oil.The Imoum Live 6-Inch Mini Chainsaw can be found here: amzn.to/47BLHHVToro Bar & Chain Oil can be found here: amzn.to/48TOWLwTo learn more about the ImoumLive Mini Chainsaw as well as other products and projects visit U Do It™️ here: udoit.me/tool-review-mini-chainsaw-for-pruning-and-tree-trimmingVideo Chapters0:00 Unboxing of ImoumLive Mini Chainsaw2:00 Filling oil reservoir with Toro bar & chain oil3:10 Installing battery3:37 First cut with the mini chainsaw4:34 Cutting 2-inch diameter branch5:25 Cutting 4-inch diameter branch7:00 Cutting 6-inch diameter branch9:54 Switching to another battery11:11 Cutting a 4-inch diameter branch12:54 Looking at the battery level indicator14:21 It's a fun tool to use“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese RecordsⓇ LLC All Rights Reserved.
An affordable compactor for rapid DIY ground compacting U Do It 2024-01-07 | There's finally an affordable compactor for rapid DIY ground compacting to help you complete your projects without costing you a fortune. Meet the BILT HARD Gas Powered Plate Compactor that features 2500 Pounds of compaction force that can compact loose dirt, soil, gravel, and more to a foundation to be built upon.I prefer to do as much if not all of the work necessary to complete a DIY project myself; hence, the term DIY or Do It Yourself. This is why I named my brand U DO IT because I do it first then you do it. But, my slogan is I DON'T DO IT - U DO IT. Finding tools and machinery that fit within the budget is an important deciding factor in both the direction of a project and if I choose to rent or purchase. Especially, if said tools and machinery can be used in future projects. We have a local tools and machinery rental company that we love. But, I do not like spending money on a rental. I would rather invest in a tool that I know I can use on another project.The price point of this compactor at the time of my purchase in early 2023 was just at the right value. I was able to purchase this compactor and use it to level the ground on my schedule. And, what is not shown in this video is the numerous times that I used it on the same project months later. For me to do this with a rental, I would have to revisit the rental company multiple times. The compactor itself is quite heavy. It is listed as weighing 126 pounds. This makes it a little difficult to maneuver alone. But, I was able to get it into place and unbox it. The packaging was done well I thought and had a combination of plywood and dense cardboard to secure it in the box. The assembly was fairly simple following the directions. The following products and materials (or similar) were used in this video:Bilt Hard Plate Compactor 2500-Pound 6.5HP Gasoline Engine: amzn.to/433kZXcDeWalt Metric Mechanic Tool Set DWMT73804: amzn.to/421CvcZDeWalt Metric Wrench Set MWMT19237: amzn.to/3Mpjiw5Sceptre 5 Gallon gas can FSCG552 or equivalent with fresh gas: amzn.to/4308w6uMr. Funnel AF3CB Fuel Filter Funnel: amzn.to/3WuvIat10W-30 Engine Oil: amzn.to/43ikIPQFloTool 10714MX3 Super Funnel Trio: amzn.to/431k6OzTo learn more about this product and other projects visit U Do It™️ here: udoit.me/do-it-yourself-build-a-shed-plate-compactorVideo Chapters:0:00 Unboxing of the Bilt Hard Gas Powered Plate Compactor1:18 Adding oil to the compactor oil reservoir2:22 Assembly of the compactor2:48 Assembly of the handle3:44 Assembly of the wheels4:26 Filling up the gas tank4:54 Assembly of throttle but it was missing a nut5:21 Starting the compactor6:18 Initial compacting7:32 Credits“As an Amazon Associate I earn from qualifying purchases.”#udoit #bilthard #platecompactorVideo Asset owned by: No Cheese Records LLCRights Management for this video: U Do It StudiosPublishing for this video: Bigginz PublishingVideo: © 2024 U Do It Studios© Copyright 2024 Bigginz Publishing℗ Copyright 2024 No Cheese RecordsDivisions of No Cheese Records LLC. All rights reserved.
Using a telescoping plank and trestles for working on my shed roof U Do It 2024-01-02 | In this video, I'm unboxing, setting up, and using a telescoping plank and trestles for working on my shed roof. I'm using my Little Giant Ladders as trestles to hold the Vevor Telescoping Plank. With this combination, I feel very confident walking about the plank.The roof of my shed is 218 inches wide and I need something economical and functionally safe. I need to be able to safely work along the width of the shed by walking along the plank. The plank will also serve as a staging area for tools and materials that are needed to work on the roof.The Vevor Telescoping Plank supports 440 pounds and can extend from its shortest of 9 feet to its longest of 15 feet. The plank is constructed of tubular aluminum and is very light to pick up and position into place. The plank does deflect some as you walk across it, which is expected. It took me a little while to get used to this. Now, I'm much more confident walking about it and have since completed my roof.Since the plank collapses down to 9 feet I will be able to easily transport it in my truck along with my Little Giant Ladders.To purchase the Vevor Telescoping Plank visit: amzn.to/3TIpcNYTo see U Do It™️ Contractor Tools for Home visit: amzn.to/3CHXveuTo learn more about the Vevor Telescoping Plank as well as other products and projects please visit U Do It™️ here: udoit.me/do-it-yourself-build-a-shed-vevor-telescoping-plank-for-roofing“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records LLC All Rights Reserved.
Using Rustoleum Copper Coat to Extend the life of Pressure Treated Wood U Do It 2023-12-26 | In this video I'm using Rustoleum Copper Coat to extend the life of pressure treated wood that I'm using to create a retaining wall. I'm using my DeWalt miter saw to cut half-lap joints that will be used to interconnect the timbers.Once the half-lap joints are cut I apply the Rustoleum Wood Life Copper Coat with a brush to the freshly exposed wood. This appears blue at first, which is typical of a copper solution. But then as it oxidizes it quickly turns to a green patina.Rustoleum Woodlife Copper Coat is available here: amzn.to/3v9BiWjTo learn more about this project as well as other projects please visit U Do It™️ here: udoit.me/do-it-yourself-build-a-shed-woodlife-copper-coat-wood-preservative“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
Using a roofing nailer to install drip edge on a shed roof U Do It 2023-12-23 | In this video, I unbox and demonstrate using a roofing nailer to install drip edge on a shed roof that I'm in the process of building. I purchased the WEN Roofing Nailer so I could complete my shed roof on my own.The WEN Roofing Nailer, which is model number WEN 61783, is shipped with a carrying case, goggles, an oiler, and the necessary hex keys to make adjustments as required. I'm using Grip Right 1 1/4" coil roofing nails that are 11 gauge, which is compatible with this nailer. I originally purchased these nails for building my original shed at our last property. That shed is a 12 x 16-foot shed with a gambrel roof that stands 16 feet tall.The purpose of a drip edge on a roof is to provide a way to divert water away from the roof line. Otherwise, water would make its way back under the shingles and underlayment. There are differing opinions about the order of ice and water shield, underlayment, and drip edge. The order is sometimes determined by the construction code in a particular region based on predominant weather conditions. For our area in New Jersey, we receive an average of 20+ inches of snow a year. I'm applying the drip edge first then the underlayment along the roof edge. Along the rake edge, underlayment is installed first followed by the drip edge. I chose not to install ice and water shield.The fascia will be installed under the drip edge. Therefore, it is important to leave a small gap under the drip edge. If a gutter were installed, it would also be installed under the same drip edge along the edge of the roof.To learn more about this and other projects and tool reviews visit U Do It™️ at:: udoit.me/do-it-yourself-build-a-shed-wen-roofing-nailerSimilar pneumatic roofing nailers are available here: amzn.to/47fORRcVideo Chapters:0:00 Unboxing of WEN Roofing Nailer Model Number 617832:18 Loading a coil of nails into the nailer4:23 Initial test of nailer4:46 Notching and mitering Drip Edge6:22 Installing drip edge on shed roof8:16 Placing underlayment over drip edge and nailing in place“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
Replacing an Over the Range Microwave Oven U Do It 2023-12-21 | Our Frigidaire Microwave oven was over five years old and stopped working last year. We love the look of the Frigidaire black stainless steel microwave and wanted to find a replacement that looked similar. At that point, we realized how convenient a microwave appliance is for life. We lived without it for over a year. Meanwhile, I tried fixing it several times with no success.We bought a new Frigidaire black stainless steel microwave to replace it. And now that we have a functioning microwave we can heat up water, have microwave popcorn, and even reheat leftovers.To learn more about this replacement and other U Do It™️ projects visit: udoit.me/how-to-replace-a-broken-microwaveMicrowave Ovens are available here: amzn.to/3vhIAag“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
UYECOVE 1/4 Inch Drive Torque Wrench Review U Do It 2023-12-18 | If you are interested in UYECOVE tools, specifically their torque wrenches, then this video is for you. The manufacturer of the UYECOVE 1/4 Inch Torque Wrench sent this to U Do It™️ for review. In the video, I highlight the packaging, the included calibration sheet, the quick-start guide, and the torque wrench settings.I also demonstrate the practical use of the torque wrench on my Craftsman Radial Arm Saw that I'm restoring.To learn more about this torque wrench as well as other tools and projects visit U Do It™️ here: udoit.me/uyecove-torque-wrench-reviewTo purchase this tool as well as other tools visit U Do It™️ store here: amzn.to/43TgChC0:00 Unboxing of the UYECOVE Torque Wrench1:00 Review of Calibration Specification1:27 Packaging1:46 Operation of the UYECOVE Torque Wrench4:05 Practical Application of Torque Wrench7:29 Setting the Torque Wrench to the lowest setting for long-term storage“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records® LLC All Rights Reserved.
I built a ridge beam and its uneven - using the DeWalt DCP580 U Do It 2023-12-14 | I built a ridge beam and it's uneven and I need a way to make it even. I have a hand planer but I always wanted a power planer. So I'm using this DeWalt DCP580 power planer that I purchased to make the job easier. This planer features a 3 1/4 of an inch wide cut with a 1/256th of an inch incremental cutting depth adjustment up to a maximum of 2mm depth per cut. I set the depth to the smallest amount.The ridge beam is fabricated from two 2x8x12s and two 2x8x8s to form a 20-foot span for my 12x16 shed. The final span will be 218.5 inches after the excess is cut off once the beam is in place. I cut the top side of the ridge beam to 15 degrees, which is what my shed plans specified. When the beam was fabricated I ensured that the beveled side was perfectly aligned. This resulted in the bottom side being out of alignment by approximately 1/8th of an inch. There are two points that the ridge beam rests on, which are the front and back supports. Other than these two resting points the rest of the bottom of the beam is irrelevant. I needed a way to flatten the bottom side at these two points of the ridge beam. And that is what this video is about - using the DeWalt DCP580 power planer to flatten these two critical points.The products used in this video can be found in the U Do It™️ Contractor Tools for Home list here: amzn.to/3CHXveuTo learn more about this planer and other tools and projects visit U Do It™️ here: udoit.me/do-it-yourself-build-a-shed-using-the-dewalt-dcp580-planer0:00 DeWalt DCP580 Power Planer Unboxing3:15 Attaching the DeWalt DCB201 battery3:41 Inspecting the area of the ridge beam that needs to be planed4:20 Attaching the rabbit fence5:00 Making the first cut with the planer6:21 Inspecting the results of several passes6:57 Working on the other end8:41 The final passes and my thoughts on the DeWalt Planer“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
Using a jackhammer to drive rebar pins into the ground U Do It 2023-12-11 | If there were a choice between setting rebar into the ground with a hammer versus a jackhammer I'll take the jackhammer. Although my choice of hammer is not the proper one for setting rebar I demonstrate how far I drive it within 40 seconds. Only if I had my sledgehammer on hand but I lost it.To purchase the jackhammer and ground rod attachment visit U Do It™️ Contractor Tools list here: amzn.to/3CHXveuTo learn more about this and other projects visit U Do It™️ here: udoit.me/do-it-yourself-build-a-shed-securing-timbers-with-rebar0:00 Intro to the Jack Hammer0:50 Cutting the rebar into 3ft sections2:27 Irwin SpeedBor 1/2 inch drill bit4:00 Drilling 1/2 inch holes into the timers5:18 Unboxing of the TR Industrial Ground Rod Driver Bit5:50 Rolling out my TR Industrial Jackhammer7:38 Attaching the ground rod driver bit to the jackhammer8:15 Attempting to use the jackhammer to drive the rebar into the ground14:01 Trying to determine why the jackhammer will not hammer16:06 I learned that the jackhammer has a feature that does not jackhammer into soft ground17:44 Continuing installation of the rebar rods for the remaining spots on the timbers23:00 Performing a test with a carpentry hammer vs. a jackhammer25:00 Test to drive ground rod with jackhammer“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
My pressure washer is leaking gas and how I fixed it U Do It 2023-11-21 | My pressure washer is leaking gas as soon as I filled the tank. Every season I expect not to be able to start my Troy-Bilt pressure washer because of issues as a result of old gas and corrosion of the carburetor. I was prepared to make the fix that I do every season, which is to clean the ports in the bowl nut. All I wanted to do was clean my driveway with a new pressure washer surface cleaner I purchased. As you can see in the video it was leaking by the carburetor. My guess is that the o-ring gasket around the bowl or the small gasket around the bowl nut failed. Rather than investigate that issue I decided to purchase a replacement carburetor. I had already removed the original carburetor in preparation for this.Once I installed the carburetor and put a little gas in the tank it started right up after a few pull starts. You'll see in this video youtu.be/N7LKAN7lj2k that I successfully cleaned my driveway with the new pressure washer surface cleaner. To purchase this replacement carburetor as well as other Briggs & Stratton small engine parts visit U Do It™️ Briggs & Stratton list here: amzn.to/3pnDV4kTo purchase tools and accessories for small engine repair visit U Do It™️ Small Engine Tools list here: amzn.to/3XpIffVTo learn more about this repair as well as other repairs and projects visit U Do It™️ here: udoit.me/my-pressure-washer-is-leaking-gas0:00 Pressure washer is leaking gas1:00 Removing air filter housing1:25 Inspecting and removing the carburetor2:44 Unboxing new briggs and stratton carburetor4:18 Installation of new carburetor7:19 Connecting fuel supply line to carburetor7:40 Installing air filter assembly8:28 Attempting to start9:03 Mrs U Do It™️ pressure washing the driveway“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records® LLC All Rights Reserved.
Restore your concrete with this pressure washer surface cleaner U Do It 2023-11-15 | You're probably watching this video because you own a pressure washer and you want to clean your concrete, patio, or driveway. And I'm going to guess that you've already cleaned your concrete, patio, or driveway with your pressure washer using the included wand. Although this works, it spreads debris all over not to mention you get covered in pressure-washed gunk.The cleaner head has two pressure washer tips that are slightly angled so the head spins while cleaning your surface. I demonstrate this on my Troy-Bilt 875EX Pressure Washer, which is rated for 2800PSI. The Twinkle Star Surface Cleaner is rated for 3100PSI. If your pressure washer exceeds this pressure do not purchase it.The Twinkle Star Pressure Washer Surface Cleaner as well as other pressure washer accessories is available on U Do It™️ Pressure Washing Essentials List here: amzn.to/44g4HdDTo learn more about the Twinkle Star Surface Cleaner as well as other products and projects visit U Do It™️ here: udoit.me/cleaning-is-so-easy-with-this-surface-cleaner“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records® LLC All Rights Reserved.
Trying the RZ Mask while cutting half lap joints U Do It 2023-11-14 | Even while working outdoors in the wind, saw dust finds its way to you. Seeing others using dust protection I decided to purchase the RZ Mask for my PPE while building my shed. The RZ Mask M2 comes with filter inserts that provide additional protection, such as active carbon filtration to remove fumes. In this case, I'm merely concerned about filtering out the dust from pressure-treated wood.You can find the RZ Mask as well as other tools for contractors and DIY professionals here: amzn.to/3CHXveuTo learn more about this product and other products and projects visit U Do It™️ here: udoit.me/does-the-rz-mask-work“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.#RZMask
How I record my workshop projects U Do It 2023-10-12 | The equipment I use to record my workshop projects ranges from tripods with cameras to lighting and C-Stands. In this video, we cover what I use to set up my shots for video production in my workshop.0:00 Video opening4:25 Light Sources6:50 Neewer C-Stand (Century Stand)13:30 Camera Rig (Panasonic G85 and GoPro Hero 5 Black)17:25 Audio (Microphone)20:50 Rode Wireless Go II Microphone22:10 Neewer RGB61 Light22:35 Setup of Neewer Lighting23:10 Setup of GoPro on Neewer C-Stand with SmallRig Articulating Arm25:35 Manfrotto Camera Backpack25:45 Joby Tripod26:50 G85 Camera Rig Setup with Anker 26800mAh and G85 Dummy Battery29:09 GoPro Mounted on C-Stand with SmallRig Super Clamp and 9-inch Articulating ArmTo learn more about this visit U Do It™️ here: udoit.me/how-i-film-my-workshop-projectsThe equipment demonstrated in this video is available from the following shop. Some models are no longer available and a suitable replacement is listed in its place.Lighting and Rigging: amazon.com/shop/udoit2/list/B4G5TZZXMKHL?ref_=cm_sw_r_cp_ud_aipsflist_aipsfudoit2_4K5ZXSGDJA8013F8BHEKAspiring Videographer: amazon.com/shop/udoit2/list/3MUJH02V5JTHI?ref_=cm_sw_r_cp_ud_aipsflist_aipsfudoit2_CA0JX1CWW363KVG282CS“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
Trimming a hedge with Greenworks 24VDC Hedge Trimmer U Do It 2023-10-05 | It's that time of year again to trim the bushes at the end of the season. Our bushes have been growing wildly over the last year and they are in desperate need of a trimming.To learn more about the Greenworks Hedge Trimmer Model Number HT24B414 visit U Do It™️ here: udoit.me/greenworks-hedge-trimmer-is-easy-to-useTo purchase this product and other lawn care and landscaping products visit my U Do It™️ Lawn Care / Landscaping List on my shop: amazon.com/shop/udoit2/list/244FB72UQ7A31?ref_=cm_sw_r_cp_ud_aipsflist_aipsfudoit2_B5AY12REKSSPNPFTK2HT“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
Saving money by growing your own garden in a raised bed planter U Do It 2023-05-17 | My goal in this video is to help inspire you to do what you can to save money by building a raised bed planter. If you have a large plot of land, you may still want a raised bed garden for peppers or tomatoes close to your house. If you live in the city a raised bed planter may be a great option for you. The goal is to save you money and not go out and buy the next best tool. If you have an old-school hand saw, by all means, use that instead of going out and buying a saw.I was fortunate to grow up at a time when my life overlapped with my grandparents' lives. They told me about the tough times they had growing up during the great depression. Though I could not appreciate it at the time it resonates well with me now. Our economy is echoing similar circumstances to what happened 100 years ago. So the time is more critical than ever to begin doing what is necessary to survive.In this video, I am using power tools. Some may say that is fancy. Others may say it is primitive. It's all relative and again that is not the point of this video. I am stressing the importance of doing things for yourself and your family to help you save money.0:00 Introduction of Raised Bed Planter0:29 Review of tools and materials used5:00 Setup of DeWalt Miter Saw5:33 Cutting 4x4 post to 30 inches long6:44 Cutting walls of the planter from 2x6 lumber8:48 Using a combination square10:14 Drilling holes with a countersink bit12:03 Adding chamfer to walls15:04 Assembly of legs and walls17:59 Adding supports for soil18:48 Flipping over the planter19:46 Rounding over sharp corners with a router22:00 Adding pocket hole screws to legs22:50 Painting inside with Flex Seal24:15 Preparing narrow crown stapler24:45 Getting DeWalt Air Hose Reel25:12 Installing wire mesh with a stapler27:35 Adding landscaping fabric28:55 BTS shooting a promo reel for other platformsTools and Materials used in this video:DeWalt DWS716 12-Inch Miter Saw amzn.to/3nZoCy9Flex Seal Spray amzn.to/42EZ4W7DeWalt Drill and Impact Driver Kit amzn.to/3MwxggHFor the additional tools, materials, and construction details see the article below.To learn more about this restoration and other projects on U Do It™ visit: udoit.me/building-it-raised-bed-planter Video Asset owned by: No Cheese Records LLCRights Management for this video: U Do It StudiosPublishing for this video: Bigginz PublishingVideo: © 2022 U Do It Studios© Copyright 2022 Bigginz Publishing℗ Copyright 2022 No Cheese RecordsDivisions of No Cheese Records LLC. All rights reserved.Song: Anti Cheese Instrumental (2023 Release)℗ Bigginz Publishing“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records LLC All Rights Reserved. No Cheese Records® is a registered trademark of No Cheese Records LLC.
Laying out rebar pins for shed and capping them for safety U Do It 2023-05-10 | I'm laying out rebar pins that are parallel to our house so the layout of our shed will be square with it. I placed two pins along the back of the house that are spaced 207 inches apart. I want to create reference pins that are exactly 207 inches apart but 320 inches away from the back of the house. Using my Craftsman Construction Calculator I was able to determine the diagonal for the rectangle which is 207 inches by 320 inches. The calculator allows you to enter Rise, Run, and then press the Diag function to calculate the diagonal. It calculated 381 1/8 inches.I have a 35-foot Stanely tape measure and a 100' Kobalt tape measure. I was able to tape the end of the 35' tape measure to the one piece of rebar. Then I noticed the Kobalt has a loop at the end for you to place it over 1/2 inch rebar. I wasn't aware this tape measure had this feature so that made things easier for me once I discovered it. To learn more about this layout visit U Do It™️ here: udoit.me/where-to-build-a-shed-in-our-backyardDeWalt 20V MAX Cordless Drill / Driver Kit DCD771C2 amzn.to/3VOJHriCalculated Industries 4325 Construction Calculator amzn.to/3nRBNAPDeWalt Tape Measure amzn.to/41hZWy9Neon Yellow Mason Line amzn.to/3BbF4hxDeWalt 7 1/4" MAX XR Circular Saw DCS574B amzn.to/3NVFtw1Bessy Clamp Woodworking Clamp amzn.to/3VQKN5NBosch Daredevil Spade Bit Set amzn.to/3pxxxXCCarpentry and Building Construction Textbook amzn.to/3nOSAEOVideo Asset owned by: No Cheese Records LLCRights Management for this video: U Do It StudiosPublishing for this video: Bigginz PublishingVideo: © 2022 U Do It Studios© Copyright 2022 Bigginz Publishing℗ Copyright 2022 No Cheese RecordsDivisions of No Cheese Records LLC. All rights reserved.Song: Anti Cheese Instrumental (2023 Release)℗ Bigginz Publishing“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records LLC All Rights Reserved. No Cheese Records® is a registered trademark of No Cheese Records LLC.
Scotts Triple Action really controls the weeds U Do It 2023-04-22 | This year I applied Scotts Turf Builder Triple Action, which feeds the lawn, provides weed control, and stops crabgrass. Last year around this time I applied Scotts Turf Builder Weed and Feed, which feeds the lawn, and provides weed control. We're seeing a much bigger difference with our lawn this year thanks to Scotts Triple Action. I applied the fertilizer using the Scotts Turf Builder with EdgeGaurd DLX broadcast spreader. This spreader offers wide dispersal for good coverage and overlap. This spreader allows you to block the edge from being fertilized using EdgeGaurd. I had the setting at the recommended 3.5 but I found that it was dispersing way too quickly so I dialed it back to around 2.5 and this worked much better.To learn more about this visit U Do It™️ here: udoit.me/scotts-triple-action-controls-weeds-and-crabgrassScotts Turf Builder Triple Action Fertilizer: amzn.to/3KX0fbxScotts Turf Builder EdgeGuard DLX Broadcast Spreader: amzn.to/3H7BzfAVideo Asset owned by: No Cheese Records LLCRights Management for this video: U Do It StudiosPublishing for this video: Bigginz PublishingVideo: © 2022 U Do It Studios© Copyright 2022 Bigginz Publishing℗ Copyright 2022 No Cheese RecordsDivisions of No Cheese Records LLC. All rights reserved.“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records LLC All Rights Reserved. No Cheese Records® is a registered trademark of No Cheese Records LLC.
Keep track of your tread wear with this handy tread depth gauge U Do It 2023-04-14 | I'm the one who ran my vehicles with bald tires for months. But now, with this handy tread depth gauge, I can keep track of the wear and know when it's time for new tires.Not all tires are the same so you need to check the specifications for your minimum tread depth. In this video, I demonstrate how to check your tread depth with this gauge.To learn more about this tire depth gauge visit U Do It™️ here: udoit.me/checking-your-tread-wear-couldnt-be-easierTire Tread Depth Gauge: amzn.to/3MGcFXMDeWalt Portable Air Compressor: amzn.to/3Uyzij0DeWalt Double Arm 50' Hose Reel: amzn.to/3MEC7NxDeWalt Battery Powered Portable Tire Inflator: amzn.to/3ofbuV2Milton Tire Inflator with Pressure Gauge: amzn.to/3zYjBbbVideo Asset owned by: No Cheese Records LLCRights Management for this video: U Do It StudiosPublishing for this video: Bigginz PublishingVideo: © 2022 U Do It Studios© Copyright 2022 Bigginz Publishing℗ Copyright 2022 No Cheese RecordsDivisions of No Cheese Records LLC. All rights reserved.“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records LLC All Rights Reserved. No Cheese Records® is a registered trademark of No Cheese Records LLC.
Spring is the time to apply weed & feed fertilizer U Do It 2023-03-27 | It's that time of year again to begin your lawn care as I'm doing here by applying Scotts Turf Builder Weed and Feed. I also purchased the Scotts Turf Builder EdgeGuard DLX Broadcast Spreader because it states that it can hold up to 15,000 square feet of lawn product. In this video, you'll see what the spreader looks like with a 43lb bag of weed & feed fertilizer.This video was shot in 2022 and we were pleasantly surprised with how well the weed & feed fertilizer worked with unwatered grass. Our friend cuts it every 8 to 10 days depending upon its rate of growth. He also edges and cleans up the grass clippings from the driveway and walkway to keep it looking as good as possible.0:00 Scotts Turf Builder EdgeGuard DLX Unboxing1:00 Scotts Turf Builder Weed & Feed setting to 3.51:28 Applying weed & feed fertilizer to lawn using EdgeGuard1:53 How EdgeGuard Works2:05 Point of view from rear of broadcast spreader2:23 My point of view of broadcast spreader2:32 Filling up spreader with Weed & Feed fertilizer and setting to 3.52:44 Spreading pattern with overlapping passes2:56 Finishing fertilizing4:04 CreditsTo learn more about this video and my thoughts on my lawncare approach visit U Do It™️ here: udoit.me/apply-scotts-weed-and-feed-in-the-springScotts Turf Builder Weed & Feed: amzn.to/3nk3r9gScotts Turb Builder Triple Action: amzn.to/3ZgMY2IScotts Turf Builder EdgeGuard DLX Broadcast Spreader: amzn.to/40AVzypScotts Turf Builder SummerGuard Lawn Food with Insect Control: amzn.to/3JLdOdNVideo Asset owned by: No Cheese Records LLCRights Management for this video: U Do It StudiosPublishing for this video: Bigginz PublishingVideo: © 2022 U Do It Studios© Copyright 2022 Bigginz Publishing℗ Copyright 2022 No Cheese RecordsDivisions of No Cheese Records LLC. All rights reserved.“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records LLC All Rights Reserved. No Cheese Records® is a registered trademark of No Cheese Records LLC.
Outlet loses power when I plug something into it U Do It 2023-03-24 | My outlet loses power when I plug something into it and in this video I troubleshoot it. But first, here's a little history of our problem. One day in band camp Mrs U Do It plugged in our vacuum and began vacuuming. Then my computer shut off and I lost internet connection while in the middle of working. I surmised that this is from a loose wire. With no time to fix it at that moment, it was still an issue. It happened again a few weeks later under the same circumstances. Almost one month later I'm here to fix the problem. In this video, you'll see I remove the outlet and show the connections. I replaced the original outlet in 2016 with this new outlet. But, when I installed it I used the push-in connectors in the back of the outlet. In retrospect, I should have used the lugs. I remove the wires by inserting a small slotted screwdriver into the wire releases. Some wires were really stuck in there and needed some significant force to remove them.Read more about this solution on U Do It™ here: udoit.me/outlet-loses-power-when-it-is-touched-or-movedU Do It™ Contractors Electrical Supply List, including the Ideal In-Sure Push-In Connectors: amzn.to/3mYrI4hU Do It™ Contractors Electrical Tools List: amzn.to/4016OjF0:00 Removing outlet from the junction box0:47 Using push-in connectors on outlet0:55 Found loose wire in push-in connection on outlet1:01 Using Ideal in-sure 30-1033 3-port push-in connectors1:09 Making a hot wire pigtail with Ideal in-sure connectors1:46 Removing wires from push-in connectors on back of outlet2:11 Making neutral wire pigtail with in-sure connectors2:52 Completing hot wire pigtail with Ideal in-sure connectors3:05 Connecting hot wire pigtail to screw terminal on outlet3:49 Connecting neutral wire pigtail to screw terminal on outlet4:48 Installing outlet in the wall and cover plate5:57 Using electrical tester to test outlet wiring6:57 Credits“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
Refilling ink on an ESPON EcoTank Printer ET-15000 U Do It 2023-03-20 | In this video, I show you how to refill the EPSON EcoTank printer on my EPSON ET-15000 using the Black 502 ink bottle. My printer was very low on black ink. It was so low that the printer was no longer permitting the printer to print.Refilling the ink was quite easy as I demonstrate in this video. One concern is that you purchase the ink close to when you know you need it. That is of course unless there are supply chain issues that we have all come to know and love. Do you sense the sarcasm? And in that case, purchase a bottle or two extra, especially if you print a lot. In our case, we did not print a lot. It is used mainly for printing contracts and making copies of receipts. In Mrs U Do It's case, she uses it to print worksheets for her classroom and sometimes legal documents.We're happy with this printer and hope that it lasts us as long as our other printer from a different manufacturer lasted.To learn more about this refilling process please visit U Do It™️ here: udoit.me/how-to-refill-ink-in-an-epson-et-15000-inkjet-printerEpson T502 EcoTank Ultra-high Capacity Bottle Black T502120-S: amzn.to/3mNRIztEPSON T502 EcoTank Ink Ultra-high Capacity Bottle Color Combo Pack T502520-S: amzn.to/3JA0NovEPSON T502 EcoTank Ink Ultra-high Capacity Bottle Cyan T502220-S: amzn.to/3mH5XG9EPSON T502 EcoTank Ink Ultra-high Capacity Bottle Magenta T502320-S: amzn.to/3JbqBWyEPSON T502 EcoTank Ink Ultra-high Capacity Bottle Yellow T502420-S: amzn.to/3ThSbGkEpson EcoTank ET-15000 Wireless Color All-in-One Supertank Printer: amzn.to/3ZXx1POU Do It™️ Office Essentials List: amzn.to/3TbO0vp“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
How well does the MUTAOMAY pressure washer clean U Do It 2023-03-14 | The MUTAOMAY 3500PSI Gas Pressure Washer provides 2.3GPM cleaning power with its 209cc engine and pump. As you can see in this video, it is easy to assemble, fill up with oil and gas, hook up the water supply, choose the appropriate spray nozzle, and begin cleaning. MUTAOMAY was kind enough to send me this Pressure Washer for evaluation.The directions were clear with only slight translation issues, which I will provide them with feedback on. There was a clear indication with a tag that the unit was shipped without oil. The pressure washer starting instructions were easily understood combined with the images. 0:00 Pressure Washer Unboxing1:26 Attaching wheels2:06 Attaching handle3:07 Installing nozzles into the handle3:31 Remove tape from the gas tank5:10 Joe helping me figure out how to affix the gas tank lid6:17 Installing water supply screen6:31 Installing pressure washer hose6:57 Review of starting instructions7:42 No oil in unit tag7:56 Assembly of pressure washer wand8:21 Attaching wand to pressure washer hose9:06 Attaching wand holder10:04 Filling up the oil reservoir11:17 Attaching water hose11:30 Filling the gas tank12:06 Filling up soap tank12:30 Priming pump by pressing wand trigger12:38 Starting pressure washer ASMR13:28 Pressure washing siding15:40 Pressure washing aluminum trim16:15 Pressure washing garage door17:56 Pressure washing brick19:26 Pressure washing concrete21:34 Pressure washing driveway22:35 How to clean brick with a pressure washer25:04 How to clean concrete with a pressure washer27:01 How to clean trim with a pressure washer28:40 How to clean a garage door with a pressure washer30:20 Cleaning concrete with a pressure washer32:47 Cleaning driveway with a pressure washer33:21 Cleaning siding with a pressure washer37:47 Cleaning brick with a pressure washer38:24 How to store MUTAOMAY pressure washer40:08 CreditsTo learn more about this on U Do It™ in this article here: udoit.me/quickly-clean-concrete-and-siding-with-this-pressure-washerMUTAOMAY 3500PSI Gas Pressure Washer: amzn.to/3TbUTx4Simple Green Oxy Solve Total Outdoor Pressure Washer Cleaner: amzn.to/3FiinutSimple Green Oxy Solve Concrete and Driveway Pressure Washer Cleaner, Purple, Unscented: amzn.to/3J5RhIh“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
Quickly measure any angle, level, or plumb with the KAPRO 985D U Do It 2023-03-10 | In this video, I look at some of the features of the KAPRO 985D Digiman 48-inch digital level. KAPRO was kind enough to send me this level to use. I unpack the level and review some of its features. I also show two possible applications where the level could be put to use.0:00 Unpacking KAPRO 985D1:24 Side view of vertical vial1:43 Review of Directions2:37 985D 9V Battery Compartment3:04 Review of KAPRO 985D digital display3:12 Percent Slope / % Slope3:36 Level Buzzer / Audible beep for level4:00 Direction arrows to achieve level5:35 Using the level in a typical scenario8:36 Measuring slope of garage floor that settledTo learn more about this level on U Do It™️ visit: http://udoit.me/kapro-985d-digiman-48-inch-digital-levelDigital levels are available here: amzn.to/47jkZ6G“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
How to Replace Battery on Craftsman LT2000 Riding Lawnmower U Do It 2023-02-26 | In this video, I'm restoring a Craftsman LT2000 Riding Lawnmower. This is the first part of the journey as I discover each issue and attempt to resolve it. The engine wouldn't crank so I decided to replace the battery with a new battery.I bought this lawnmower in 2006 when we bought our second home on a 1/2 acre property. Mowing the property with a 21" walk-behind lawnmower, although a great way to exercise combined with landscaping maintenance, is a time killer. So I purchased this Craftsman LT2000 lawnmower from a Sears outlet store for $1,500.The Craftsman LT2000 lawnmower uses a Group U1 type 12 Volt battery with at least 250 cold cranking amps.To learn more about this restoration and other projects on U Do It™️ visit: udoit.me/installing-new-battery-in-a-craftsman-lt2000-riding-lawnmowerThe tools and materials used in this video are as follows:Mighty Max Battery ML-U1-CCAHR: amzn.to/3IEa6SKKaiweets DMM: amzn.to/3Y7fVO2Socket Set: amzn.to/3XYJVvrTorx Bit Set: amzn.to/3KEjlER“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
Bigginz Group Therapy The Movie 4k Featuring Savvy Turtle and Northside Nate U Do It 2023-02-12 | Savvy Turtle and I are great friends. But, Savvy is for Cheese and I’m No Cheese and this results in constant battles between us. So we’re in group therapy trying to sort this siht out. And that’s why this is Bigginz Group Therapy!Movie Credits on TVM: https://tvm.fyi/titles/455/bigginz-group-therapy-the-movieCast:Luke Franklin: https://tvm.fyi/people/8662/luke-franklinAnthony Barone: https://tvm.fyi/people/8658/anthony-baronePeter Barone: https://tvm.fyi/people/8659/peter-baroneU Do It: https://tvm.fyi/people/8660/u-do-itAlso available on Turtle Tube https://turtle.tube/v/hEjtOO0:00 Bigginz Group Therapy The Movie Mezzanine 0:06 U Do It - Bigginz Group Therapy Official Music Video3:20 U Do It - Bigginz Group Therapy Official Lyrics Video6:35 U Do It - Anti Cheese Official Audio9:27 U Do It - Anti Cheese Official Lyrics Video12:21 U Do It - Hold The Cheese Official Audio15:57 U Do It - Cheese Trauma Official Visualization Video19:13 U Do It - No Cheese Anthem Official Visualization Video22:53 Credits24:09 Luke Franklin - I Can't Even24:12 Mrs U Do It - Poppin Tags24:26 Luke Franklin - That's Just Wrong24:32 Luke Franklin - Yes, That's Right24:44 Luke Franklin - You Are Correct24:52 Luke Franklin - You Da Man24:59 U Do It - Wearing U Do It Patriotic WerkJaqket25:16 Anthony Barone25:20 Peter Barone25:24 Luke Franklin - Yes, I Need That26:40 Special Thanks to Volpe's, Eddie Shapiro, Bigginz Nutz BarVideo Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
Fabricating fasteners using my Lincoln Electric 210MP Welder U Do It 2023-02-10 | This video shows you how I'm fabricating fasteners out of threaded rod and flange nuts with my Lincoln Electric 210MP welder. I decided on this path out of necessity since I was unwilling to spend $270 on bolts (I found 10 bolts for $90). See, I'm building a bed for our son and my plans call for 11-inch bolts. They will be counter-bored into cross members that are 12 inches tall and threaded into T-Nuts, which will also be counter-bored from the bottom. I visited my favorite metal supply shop in our area, which is Fazzio Steel. There I was able to pick up 5/16-18 threaded rods, flange nuts, T-Nuts, and washers. I also purchased a used chop saw that I was able to use to cut down the threaded rod. Altogether, it was still cheaper than $270 and I got a new tool that will help in future projects.0:00 Intro to Fabricating Fasteners0:13 Cutting Threaded Rod into 11-inch sections2:15 Deburring with belt sander2:57 Feeding of NR-211-MP Flux-Cored wire4:21 Adapter to connect 240VAC welder plug to generator5:24 Welding flanged nuts to threaded rod with Lincoln Electric 210MP Welder8:11 Grinding welds with DeWALT DWE4011 and Blue Hawk flap discs10:26 Behind The Scenes video of fasteners11:35 Review of flux-cored wire setup12:55 Review of generator to welder plug adapters 13:22 NG-50R Plug to L14-20 AdapterVisit U Do It™️ to learn more about this welder: udoit.me/fabricating-fasteners-with-lincoln-electric-210mp-welderU Do It™️ Metal Working Essentials Shop: amzn.to/3XfHNPBLincoln Electric 210MP Welder K3963-1: amzn.to/3jGHVKgLincoln Electric MIG Welding Wire NR-211-MP: amzn.to/3Yl4aokLincoln Electric KH962 PRM Welding Gloves: amzn.to/3DLuy2jLincoln Electric Heavy Duty Leather Welding Jacket K2989-XL: amzn.to/3Yg9nxoLincoln Electric MIG Welding Pliers K4014-1: amzn.to/3RF0mLXDeWALT Metal Cutting Saw DW872: amzn.to/3lcWfuiWORKPRO 8-inch Welding Pliers: amzn.to/3XfxgDSOptrel VegaView 2.5 Welding Helmet 1006.600: amzn.to/3JP1r1OParkworld 691920A Generator to Welding Adapter Cord 240V: amzn.to/3Xcu2BmDeWALT 4-1/2 inch Angle Grinder DWE4011: amzn.to/3YdD8z1Black Hawk Grinding and Sanding Flap Discs T27 40-Grit: amzn.to/3XdFzAi“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
DeWALT DWS780 Miter Saw with Dual Bevel and XPS Review U Do It 2023-02-03 | In this video, I unbox the DeWALT DWS780 Miter Saw with Dual Bevel, set up the saw, make some initial cuts, and explain how the saw works and how to calibrate and adjust it.0:00 DeWALT DWS780 Unboxing0:30 Saw Setup - Installing Extension Arms0:52 Testing the smoothness of the sliding linear bearings1:01 Checking the saw for square1:20 Initial cut using 45° bevel2:00 Setting Bevel to 0 degrees and making a 90° cut2:17 Checking cross cut for squareness2:26 Demonstrating XPS LED cutline2:44 Locking / Unlocking saw3:00 Calibrating miter angle and bevel angle to 0 degrees3:45 Replacing DWS3126 Contractor 60 Tooth blade with Diablo D1280X7:47 Using Slide Lever Lock to Cut Trim Vertically9:49 Cutting trim board laying flat on the miter saw table10:56 Using sight to line up scribe line and blade through saw blade guard11:44 How to Turn on the XPS LED12:12 How to use the miter saw clamp13:13 Power Switch safety feature13:45 Using XPS LED as a reference to the scribed line14:01 Measuring and cutting to length test and a quick lesson on uncertainty15:56 How to Transport Saw16:56 How to adjust miter angles with and without angle detents20:33 Using Bevel Pawls for 22.5 and 33.9-degree bevel21:58 Using 0° Bevel Override to bevel to the right22:49 Using the grooving stop for dados and rabbits28:12 Horizontal cut capacity (boards laying flat on the table)28:49 Vertical cut capacity (trim boards standing upright)30:00 How to access the belt for replacement31:48 Using 45° stops to reach 49°32:46 Setting bevel to 45° to make the cut on my bed skirtDeWALT DWS780 Sliding Compound Miter Saw with XPS: amzn.to/3juKYFkDeWALT Miter Saw Stand with Wheels DWS726: amzn.to/3HoAUW8DeWALT Miter Saw Crown Stops DW7084: amzn.to/3X2KVOPDeWALT Miter Saw Clamp #630065-00 2 pack: amzn.to/3YnDwKLDeWALT 12" Miter Saw Cross-Cutting Blade DW3128P5: amzn.to/3HQUpbxDiablo 12" 80 Tooth Finishing Saw Blade: amzn.to/3l7RLW1To learn more about this saw and its setup on U Do It™️ visit: udoit.me/dewalt-dws780-miter-saw“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
Protect your Cabinets with Drawer and Shelf Liner U Do It 2022-12-30 | I built this pantry cabinet for our kitchen to give Mrs U Do It more storage. So we want to know the best way how to protect kitchen cabinet shelves. We wanted to find a high-quality slip-resistant shelf liner to protect every shelf. Our cabinet is 24 inches deep and over 25 inches wide so I needed a wide shelf liner with over 10 feet for our five shelves. I found and purchased Gorilla Grip Premium Drawer & Shelf Liner which is 24 inches wide and 20 feet long. In this video, I show you how I cut the liner and how I install the shelf liner on each shelf of our pantry cabinet.Our pantry cabinet has 3 removable shelves and 2 fixed shelves. It was easiest to start with a removable shelf as a template. I removed everything from the shelf and placed the shelf on our kitchen table. Once I opened the shelf liner roll I was able to size it up, clamp it in place onto the shelf and cut it to length. I used my Stanley Utility Knife with a new blade to cut the shelf liner. As I cut I made sure that I rested the end of the utility knife on the shelf while allowing the blade to glide along the edge of the shelf. This cut the shelf liner to the exact width of the shelf. Clamping the liner to the shelf made this work much easier since the shelf liner was nearly immovable during cutting. I got a little fancy and cut around the magnetic latches that hold the door into place when closed. The utility knife made easy work of this allowing me to cut the shelf liner in place.0:00 Introduction to Gorilla Grip Liner0:38 Sizing up the liner for the shelf1:17 Making the first cut2:11 Installing the shelf with the liner3:04 Clearing off next shelf3:30 Aligning liner to the shelf and clamping it down4:20 Making the next four liner cuts6:00 Installing the second shelf with liner6:28 Cutting around magnetic latches and face frame6:45 Lining the other two shelves and filling the cabinet7:35 Impressions of Gorilla Grip Drawer and Shelf LinerVisit U Do It™ to learn more about this installation: udoit.me/protect-your-cabinets-with-drawer-and-shelf-linerGorilla Grip Shelf Liner: amzn.to/3v5wPAqStanley 99E Utility Knife: amzn.to/3HUv7K8“As an Amazon Associate I earn from qualifying purchases.”
How to Install a Door Lever U Do It 2022-12-24 | Your choice of hardware can really make a room pop. For our son's bedroom, we love the look of oil-rubbed bronze together with the pewter walls and white molding and doors. In this video, I unbox and install the Honeywell Wave Privacy Door Lever model number 8106402. This door lever is finished in oil-rubbed bronze and features an interior lock for privacy.Our choice of the interior door was the two-panel with the curved top to give a more sophisticated look. And this style is consistent with the doors we chose for our son's music studio. As you walk through the hallway you will notice this consistent look between the door styles, molding, and hardware. We still have a ways to go since the hallway isn't complete but that is a task for another day.0:00 Honeywell Door Lever 8106402 Unboxing0:34 Installing the Adjustable Latchset0:57 Installation of Door Lever1:50 Install #8 Machine Screws to secure Outside Door Lever to the Inside Door Lever3:47 Secure Latch-Plate into the edge of the door4:00 Install the Strike Plate5:10 Apex 3-Inch u-Guard Protective Sleeve BenefitInstallationThe package contains the door lever and a box of hardware for installing it including the door latch and strike plate. Recommended tools for installation include a Phillips-head screwdriver and maybe a rubber mallet or hammer. Install the door latch first with proper orientation so the door will close and latch properly. This may require a light tap with a rubber mallet or hammer. However, use care as you can bend the metal on the Springlatch faceplate especially if the edge bore hole for the latch assembly is not the correct size. If you are installing this on an older existing door, you may find that the edge bore hole is not the correct size. For newer manufactured doors a standard size for the face bore and the edge bore is used. Visit U Do It™️ for more installation details: udoit.me/how-to-install-a-door-lever-for-a-bedroomTools and Materials UsedHoneywell Wave Privacy Door Lever model number 8106402: amzn.to/3GgEfreAPEX u-Guard Fastening Set: amzn.to/3FJunVmDrill / Driver like the Ridgid R86034: amzn.to/3PXIfzZRubber Mallet or Hammer: amzn.to/3FRhR6i“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
Making our home shine with custom built light stands U Do It 2022-12-03 | We love the Novostella 20 Watt Smart LED Lights so much that we bought the Novostella 25 Watt Smart LED Lights. But, our placement at ground level wasn't sufficient. So, I wanted to raise the newly purchased lights to a higher level to paint the house with light. To satisfy this desire I wanted to craft light stands. This video demonstrates the building of these light stands, their installation, and the configuration of the Novostella lights within the SmartLife app.I would like to give special shoutouts to the following local companies:Friends at Matteo Iron & Metal in Thorofare, NJ where I was able to purchase the scrapped sheet metal for use as a base for the light stands.Joseph Fazzio, Inc. in Glassboro, NJ for their incredible supply of metal where I was able to purchase the steel tubing.Video Chapters:0:00 Demonstrating Light Stands in Use0:04 Cutting light stand base with DEWALT angle grinder1:30 Using BlackHawk 40 Grit flap discs to grind off the rust2:09 Cutting down steel tubing to length2:24 Grinding off mill scale from tubing3:00 Welding tubing to the base3:47 Prepping surface for priming4:24 Using RUST-OLEUM comfort grip4:50 Drilling hole in stand for mounting Novostella 25 Watt Smart LED Lights6:30 Priming light stands with RUST-OLEUM Automotive Primer8:20 Painting stands with RUST-OLEUM K7758 Hunter Green Enamel9:02 Mounting Novastella 25 Watt Smart LED Lights to stands9:24 Connecting lights with Iron Forge 1 to 4 extension cord splitter10:06 Connecting Novastella lights to Smart Life app10:44 SmartLife app automatically detected smart floodlight10:52 Using Cord Protect weatherproof connector12:03 Using Iron Forge 1 to 4 extension cord splitter for other lights13:16 Using Cord Protect14:24 Configuring Novostella in SmartLife app14:45 Setting the startup color of the light in the SmartLife app15:16 Sit back and enjoy your setupVisit U Do It™️ for the full details on this build: udoit.me/making-our-home-shine-with-custom-built-light-standsMetal Cutting and Surface Grinding Products used:DEWALT DWE4011 Angle Grinder: amzn.to/3VsYzL9BlackHawk 40 Grit Grinding and Sanding Flap Discs: amzn.to/3ujyXUUJorgensen Ratchet Bar Clamps: amzn.to/3H4FYAtWelding Products used:Welding Magnets: amzn.to/3H4hdV7Lincoln Electric 210MP Welder: amzn.to/3FlyEzhLincoln Electric Welding Gloves: amzn.to/3OWdUBoOptrel VegaView 2.5 Welding Helmet 1006.600: amzn.to/3uj2zBPWelding Rods: amzn.to/3UoIHbeGenerator for power welder: amzn.to/3VMPxrWPainting Products used:RUST-OLEUM Protective Enamel K7758 Hunter Green: amzn.to/3gODFXPRUST-OLEUM Automotive Primer: amzn.to/3VKGI1XRUST-OLEUM Comfort Grip 241526: amzn.to/3EZFp8mLights and Extension Cords:Iron Forge 1 to 4 Extension Cord Splitter: amzn.to/3itVRGvCord Protect Outdoor Extension Cord Safety Cover: amzn.to/3VILVr8Novostella 25 Watt Smart LED Flood Lights: amzn.to/3EZJ2Lw“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
KODAK Mini 3 Retro Photo Printer Demonstration U Do It 2022-11-29 | The KODAK Mini 3 Retro printer prints high-quality images right from your iPhone or Android over Bluetooth. The printer comes with a charging cable that plugs into the built-in USB port for charging the printer. This video is an unboxing of the KODAK Mini 3 Retro Printer Gift Bundle and follows with a demonstration using my Android Samsung Galaxy S20 Ultra. 0:00 Introduction to printer0:05 Unboxing Gift Bundle1:38 Unboxing KODAK Mini 3 Retro Printer 2:20 Unboxing 3 x 3 Print Cartridge2:34 Charging printer3:16 Installing KODAK Photo Printer app on Android phone3:49 App setup and permissions4:48 Connect to printer via Bluetooth5:38 Selecting photo to print6:30 My first print7:20 Photo print reveal7:50 Printing another photo of me and Mrs U Do It8:44 Second photo comparison to actual photo8:56 Turn off printer9:16 Placing prints in the included photo albumTo learn more about this printer and other articles from U Do It visit: https://savvyturtle.rocks/kodak-mini-3-retro-photo-printerThis kit that I received, which was sent by KODAK to me as part of a promotion in that I am participating, contains the following:- KODAK Mini 3 Retro Photo Printer with 8 sheets- Charging cable- Photo Album- Stickers- Clothing Pins for hanging photos- A carrying case- 60 3 inch square photo sheets- A retro tin for storing printed photosTo purchase the KODAK Mini 3 Retro Photo Printer or other KODAK bundles visit: amzn.to/3VwvXA5U Do It™️ Truth Statement: You can count on U Do It to provide an honest product review. If U Do It finds a problem or something stinks U Do It will tell you. And, if U Do It thinks it's awesome you'll know. U Do It's opinion is not influenced in any way. In the event we create a follow-up video, we will include a link point to it.“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
Cleaning two-story gutters with a pressure washer & Sun Joe Gutter Cleaning U Do It 2022-11-18 | Keeping your gutters clean is important for the longevity of your roof line, fascia and foundation. We have an oak tree that drops leaves every year on our roof and clogs our gutters and it overflows with pouring water on our deck and at the base of our foundation. I'm not a fan of climbing a ladder that big to clean the gutters. I'd much rather use power equipment like Tim Allen on Home Improvement. You even hear me grunting throughout this episode.My pressure washer is the Troy-Bilt 875EX with a Briggs & Stratton engine. I bought the VEVOR Telescoping Pressure Washer Wand and the Sun Joe SPX-GCA315 315-Degree Gutter Cleaning Attachment to clean my siding and clean out my gutters. I needed the telescoping wand since our home is two stories tall.Buy Sun Joe SPX-GCA315 315-Degree Gutter Cleaning Attachment here: amzn.to/3XaVpg9Buy VEVOR Telescope Pressure Washer Wand here: amzn.to/3THW8T3Visit U Do It™️ to learn more about cleaning your gutters or other Home Improvement videos: udoit.me/cleaning-two-story-gutters-with-a-pressure-washer0:00 Connecting the VEVOR Telescoping Wand to Pressure Washer0:18 Cleaning gutters above garage0:59 Cleaning gutters above 2nd floor1:47 Connecting GoPro to Sun Joe gutter cleaning wand2:00 Making 2nd pass 3:27 Cleaning gutter for 3rd pass4:28 Making another pass to thoroughly clean gutters“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
I bought a Generator from a scrap yard but will it run U Do It 2022-11-11 | I bought a Generator from a scrap yard but will it run when I try to start it? My mentor challenged me to find items, repair them, clean them up and sell them. I visited our friend Jim Matteo's business Matteo Iron & Metal in Thorofare, NJ on Saturday, November 5th to see what they had just received. After looking through everything I found this Generac GP5500 Generator on a pallet just sitting there. I bought it and they loaded it up onto my truck bed using their forklift.I got the generator home and... To learn more about this generator read the U Do It™️ article here: udoit.me/i-bought-a-generator-from-a-scrap-yard-will-it-runGumout Starting Fluid 5072866: amzn.to/3EehGSIGumout Carb / Choke Cleaner 800002230: amzn.to/3tfNQHaSmall Engine Repair Tools: amzn.to/3VZXWJAVideo Chapters0:00 Generac GP5500 Generator0:40 Filling generator with gas and initial start1:57 Remove Air Filter Assembly with 10mm Socket2:28 Remove Fuel Line from Carburetor3:25 Flush out tank with fresh gas3:45 Remove governor spring and rod4:20 Remove Carburetor4:26 Remove Bowl Nut with 14mm Socket4:42 Inspect Bowl Nut4:58 Clean Bowl Nut with Carb Cleaning Tools6:40 Clean Bowl Nut with Carb Cleaner7:20 Clean Main Jet in Carburetor with Carb Cleaner8:07 Remove Bowl from Carburetor8:30 Clean Float and inside of carburetor with cleaner9:10 Ensure bowl is clean9:26 Clean out Main Jet with a tool9:44 Spray clean the Main Jet10:10 Reassemble and Test 13:00 Fuel not getting into bowl14:06 Disassemble with goal to inspect fuel path14:38 Spray carb cleaner in Fuel Inlet in Carburetor14:56 Remove float pin15:18 Carefully remove needle and float - it was stuck in mine15:36 Clean out port where needle seat is16:18 Clean off Needle - Careful not to lose spring17:36 Ensure Needle is cleaned well19:00 With Needle, Spring and Float reassemble19:34 Install Float Pivot Pin20:30 Install Bowl and Bowl Nut21:04 Install Carburetor and Reassemble21:30 Spray with starting fluid and Test“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
How to Fill Windshield Washer Fluid in 2022 Dodge Ram 1500 U Do It 2022-11-04 | My low wiper fluid indicator was lit on my dashboard cluster. I decided to document how to replace it. So, in this video I demonstrate how to fill the windshield washer reservoir on my 2022 Dodge Ram 1500. Rain-X washer fluid is my first choice and I always have extra on hand in case we run out in an emergency. 0:00 Wiper Fluid Indicator Lit0:15 Pull the hood release lever0:24 Open the hood0:30 Locate the windshield washer fluid tank0:37 Fill the wiper fluid reservoir1:11 Close the lid to the tank1:22 Close the hood1:27 Start the truck1:35 Observe wiper fluid reservoir1:47 Test the Windshield Wiper FluidTo purchase Rain-X or other products visit U Do It™️ Automotive List: amzn.to/3gI7xEOTo learn more about filling your windshield washer fluid reservoir visit: udoit.me/how-to-fill-windshield-washer-fluid-in-a-dodge-ram“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
Battery powered chainsaw gives you flexibility without gas U Do It 2022-10-28 | I purchased the Greenworks 40V 16 Inch Chainsaw because I found that I was limited with only using the Greenworks 40V Polesaw. It was difficult cutting fallen branches or big branches with the polesaw. After all, the job of the polesaw is to cut branches at a high level where it is difficult to reach. 0:00 Unboxing Greenworks 40V 16 Inch Chainsaw0:29 Battery is super low charge0:42 Using my other 40V 2Ahr battery0:49 Inspect and fill with Toro Bar and Chain Oil1:49 Removing blade guard and testing chainsaw2:09 Power button to turn on and off2:30 Initial cuts with chainsaw3:48 Now using my Greenworks 40V Polesaw5:27 Fixing chain that popped off of polesaw6:20 Back to trimming the tree7:22 Using chainsaw to cut up fallen branchesGreenworks 40V 16 Inch Chainsaw: amzn.to/3W7xr54Greenworks 40V 8-Inch Polesaw: amzn.to/3DH1f1mToro Bar and Chain Oil: amzn.to/3SOzqbnSee the U Do It™️ list of other lawncare products: amzn.to/3D1CwD2To learn more about this chainsaw and its usage as well as safety resources that are available read about it here: udoit.me/battery-powered-chainsaw-gives-you-flexibility-without-gas “As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
How to clean siding on a 2 story house with a pressure washer U Do It 2022-10-21 | In this video I demonstrate how to clean siding on a 2 story house with a pressure washer extension wand. This is a 24 foot extension wand that I purchased and it allows me to reach up to the 2nd floor level siding. It requires some strength to manage the wand as it becomes heavy at an angle. Over time the difficulty can increase as your muscles begin to fatigue. 0:00 Filling pressure washer cleaner with Purple Power0:15 One pull start since I replaced the carburetor0:35 Beginning cleaning of gutter and fascia of 2 story house2:20 Cleaning siding18:26 ran out of gas and packing up wand and hoseSafety FirstThis extension wand is made of conductive metal. This means coming in contact with electric wires can result in shock or electrocution. Be aware of your surroundings and if at any point you do not feel comfortable performing this activity it is highly recommended that you consult a professional.To this wand and other items please visit my pressure washing essentials list by U Do It™️: amzn.to/3gixNFzTo learn more about this application and other articles visit: udoit.me/how-to-clean-siding-on-a-2-story-house-with-a-pressure-washer“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
My Pressure Washer Wont Stay Running - How to Fix U Do It 2022-10-14 | Your pressure washer wont stay running because it was in storage like mine for quite a while. Although you were able to get it started by cleaning the main jet in the carburetor it just wont stay running under demand. My problem was I had dirty fuel that sat in the tank for over two years without running. The contaminants in the fuel can clog up the carburetor, which will lead to the engine stalling under demand (using the pressure washer or having water pressure). You may have seen the video my neighbor Joe and I made when he helped me with this same pressure washer. The problem was a clogged main jet due to debris in the fuel.Briggs and Stratton Engine Parts, Supplies U Do It™ List: amzn.to/3gKph2pSmall Engine Tools U Do It™ List: amzn.to/3VZXWJATo learn more about this repair read this U Do It™️ article: udoit.me/my-pressure-washer-that-wont-stay-runningVideo Chapters0:00 Pressure Washer Starts but wont stay running0:17 Troy Bilt 2800 Max PSI with Briggs & Stratton0:35 Remove the carburetor main jet for inspection1:16 Clean main jet ports1:27 Reinstall Main Jet1:41 Start Pressure Washer2:03 Tools needed to replace Carburetor3:04 Remove Cover4:07 Remove Air Filter Assembly5:02 Remove Carburetor and Linkages6:09 Remove Fuel Line to Carburetor8:23 Inspect Gaskets and O-Rings - replace if necessary9:05 Connect Linkages to new Carburetor9:37 Install Mounting Plate & Carburetor10:28 Install Spring in correct location10:50 Cut Fuel Line for new Fuel Filter12:10 Install new Fuel Filter and Clamps12:35 Connect Fuel Line to Carburetor and Clamp12:50 Install Air Filter Housing, Tube to Air Filter, Wires to Switch15:50 Install Air Filter & Close16:05 Install Cover16:39 Fill Fuel Tank with fresh gas17:17 Check Oil & fill if necessary18:06 Connect water and Pressure Washer Hose18:17 Turn on Switch and Start20:00 Pressure WashBriggs and Stratton replacement carburetor as shown in this video: amzn.to/3TczwKLWhat Can you Check?- Contaminated fuel in the tank- Main jet ports clogged- Air filter dirty- Spark plug is corroded- Bad needle valve“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.
How to make a crown molding return for the professional look U Do It 2022-10-07 | Your considering installing crown molding and you're not sure how to make a return for that professional look. In this video I demonstrate how to cut a crown molding return on a compound miter saw without using the bevel. What is a return? A return is also known as a molding end stop. A return is a way of making molding look like the end stops at the wall (or returns into the wall). For this cut I install the D1280X Diablo 80T Fine Finish blade on my DeWalt 12" Compound Miter Saw. I was able to use Jorgensen EZ-Hold clamps to create a point for the crown molding to rest against on the miter saw at the perfect spring angle. This allowed me to cut the crown molding only with the miter without the need to calculate and set the proper bevel angle.Why is this crown molding lower than the ceiling? I built it down lower so I can install lights in the crown molding as I did in this other video. Lighted Crown Molding: youtu.be/9SV7-c4xt8IDiablo D1280X 80T Fine Finish Blade: amzn.to/3gxnXjcThe tools and materials used for cutting and and creating the crown molding return can be found on my U Do It™️ Crown Molding LEDs list: amzn.to/3DrmBiYTo learn more about this installation, a detailed list of tools and instructions visit this U Do It™️ article: udoit.me/how-to-cut-a-crown-molding-return0:00 Crown Molding Return Intro0:07 D1280X Diablo 80T Fine Finish Blade Installation0:21 The angle that needs to be cut for the return0:34 The first cut0:55 Cutting the return piece1:22 Rough fitting crown molding and return1:32 Glue the return piece using Bob Smith CA glue2:34 Rough fitting the crown molding assembly2:46 Apply CA glue to inside corner3:04 Hang the crown molding and return assembly with finish nailer3:17 Install shims just for extra force until CA glue sets on inside corner“As an Amazon Associate I earn from qualifying purchases.”Video Credits:Video Production: U Do It™️ Studios a Division of No Cheese Records™️ LLC All Rights Reserved.Credits:_________________Freud Diablo BrandBob Smith Industries BrandDeWalt BrandRidgid Brand
