Transcript: The repair we're looking at is the loss of drive -- and in this case, what we have is a damaged drive unit. If you notice, the drive unit will not rotate. So, what we've done -- we've ordered a new drive unit. When you order the new drive unit, in the kit will come instructions, 4 new screws, the new belt and a complete unit. Always check to make sure that the unit does spin freely. And, we're going to change this unit out with the correct unit. We're going to start with a T-25 Torx and remove the screws. Once the 4 screws have been removed, the unit will then move and then release from the cradle. Release the arms. Remove the unit and the belt. When reinstalling, make sure that the speed screw is on the outside. Make sure that the arms snap into the cradle. When reassembling the screws, we're going to use blue Loctite -- just a dab. We're going to torque the screws to 2.5 ft-lbs. You want to make sure that the wheel spins freely.
How to Replace the Driver Unit on a CVT Transmission of a Riding MowerSears PartsDirect2023-05-05 | This #diy video shows how to #replace the Drive Unit on a CVT RS800 #transmission of a riding lawn mower or lawn tractor.
The Drive Unit spins the Driven Pulley to move the riding mower.
Replace the Driver Unit when it locks up and won't spin.
Transcript: The repair we're looking at is the loss of drive -- and in this case, what we have is a damaged drive unit. If you notice, the drive unit will not rotate. So, what we've done -- we've ordered a new drive unit. When you order the new drive unit, in the kit will come instructions, 4 new screws, the new belt and a complete unit. Always check to make sure that the unit does spin freely. And, we're going to change this unit out with the correct unit. We're going to start with a T-25 Torx and remove the screws. Once the 4 screws have been removed, the unit will then move and then release from the cradle. Release the arms. Remove the unit and the belt. When reinstalling, make sure that the speed screw is on the outside. Make sure that the arms snap into the cradle. When reassembling the screws, we're going to use blue Loctite -- just a dab. We're going to torque the screws to 2.5 ft-lbs. You want to make sure that the wheel spins freely.
If you need to have a Sears Technician install the new Drive Unit on your RS800 transmission, schedule service at searshomeservices.com/repair/riding-mower-repair-serviceHow to Set Up Your Snowblower for Winter | #snowremoval #setup #prepareSears PartsDirect2023-10-20 | This video shows how to set up your snow blower or snow thrower for the winter snow removal season. Get tips on storing shear pins, positioning drift cutters and adjusting tire air pressure so your snowblower is ready to go for the first snowfall.Clean the Dishwasher Filter | #dishwashers #cleaning #diySears PartsDirect2023-10-20 | This video how to clean the dishwasher filter in common Kenmore, Whirlpool, Maytag and Amana dishwashers. Remove the filter and clean out debris monthly. Scrub off deposits using a soft bristle brush.How to Adjust Snowblower Skid Shoes | #diy #adjustment #snowremovalSears PartsDirect2023-10-13 | This DIY video shows how to adjust the snowblower skid shoes. Skid shoes raise the shave plate about a quarter inch to keep the plate from wearing out quickly.
1. To adjust the skid shoes accurately, lay down a sheet of cardboard or flattened shipping box that’s almost as wide as the shave plate. 2. Place the cardboard so that it’s under the shave plate but not under the skid shoes. 3. Loosen the skid shoe bolts on both sides so the shoes drop down flat on the ground. 4. Tighten the skid shoe bolts. Skid shoes can wear down quickly, so keep the cardboard handy and check skid shoe position often. Adjust when needed, to keep from wearing out the shave plate.Testing a refrigerator thermistor | #diy #refrigerator #repairSears PartsDirect2023-10-12 | This video shows how to test a common refrigerator thermistor using a multimeter. The thermistor is a temperature sensor. The resistance of the thermistor changes proportionately with temperature. The electronic control board in the refrigerator detects temperature by sensing the resistance through the thermistor.
Use the procedure shown in the video to test the thermistor in your refrigerator.
Note: The resistance value at the measured temperatures may be different for your refrigerator.Front-Load #washer #tumbling #action illustratedSears PartsDirect2023-10-05 | See the different #tumbling actions in a front-load #washer . The actions include:
Rolling Scrubbing Stepping Swinging Tumbling
These #washing actions get your clothes clean in a front-load washing machine.
If your washer isn't working as it should, schedule a repair appointment on our Sears Home Services website: searshomeservices.com/repair/washer-repair-serviceHow to Replace the Lid Lock on a Common WasherSears PartsDirect2023-10-04 | This DIY repair video from Sears PartsDirect shows how to replace a broken lid lock in common Kenmore, Whirlpool, Maytag and Amana top-load washers. If your washer won’t run even though the lid is closed, or you notice that the Lid Lock light is flashing, you may need to replace the lid lock.
This repair guide covers vertical modular washers in the Kenmore 110-series. It also covers vertical modular washers in the Whirlpool Cabrio series and Maytag Centennial series. Vertical modular washers use a super-high-speed spin cycle that extracts water from the load; the lid stays locked to protect you from the fast-spinning parts.
Visit us at https://www.searspartsdirect.com?sid=soc:youtube:how-to-replace-the-lid-lock-on-a-kenmore-vertical-modular-washer
Or call 1-800-437-1673 to speak with a parts specialist.
Possible symptoms: 1. Washer won’t run 2. Lid lock light flashing
Or click here to schedule an appointment with a repair technician. searshomeservices.com/repair#showallResetting the water heater limit switch #diy #waterheater #resetSears PartsDirect2023-10-04 | This DIY troubleshooting video shows how to reset the high-temperature limit switch on your electric water heater when you get no hot water.
Shut off the house circuit breaker for the water heater before accessing the thermostat and pressing the red limit switch reset button.
Monitor water temperature after resetting the high-temperature limit switch.
Get 10% Off your parts order -- use promo code YOUTUBE .
If you need to have a Sears Technician visit your home and repair your water heater, set up an appointment on our Sears Home Services website: searshomeservices.com/repair/hvac/water-heater-repair-serviceWash the dryer lint screen regularly to keep your clothes #dryer working properly #diy #maintenanceSears PartsDirect2023-09-26 | This video shows to regularly wash the clothes dryer lint screen to remove dryer softener sheet residue that builds up on screen.
Washing the screen regularly can help your dryer run its best and save energy.
You’ll want to do this every few months, or when you notice it takes longer for clothes to dry.
First, remove all the lint from the screen. You probably can’t see the fabric softener deposits that build up on the screen.
Before you shove that lint screen back into the dryer, check to see if water easily flows through the screen holes. If not, then you'll definitely want to wash the lint screen.
To remove residue from fabric softener, run warm water over the lint screen while wiping with a soft-bristled brush. Some owner’s manuals also recommend using detergent or vinegar to help clean deposits off the lint screen.
Let the lint screen air dry completely before reinstalling it in the dryer.How to Replace a Samsung Refrigerator Reservoir and Water Filter Housing Part DA97-14655CSears PartsDirect2023-09-25 | This #diy #repair video shows how to replace the Refrigerator Reservoir and Water Filter Housing part number DA97-14655C in a common Samsung side-by-side #refrigerator.
Unplug the refrigerator and shut off the water supply before beginning the repair.
Pull the refrigerator out to access the water supply connection on the back of the fridge.
Transcript: To get access to the water filter housing and water reservoir, first, turn off the water supply. Pull the refrigerator out and go to the rear of the refrigerator. Remove the cover for the water line. You'll need slack in that water line later on in the repair. You'll also need slack in the 2 water lines that go to the freezer door hinge. They're clipped right underneath the cabinet. Pull those water lines out and disconnect the John Guest fittings. Next, pull out the drawers and shelves. Remove the water filter. Remove the 2 screws from the housing. At the back of the housing, there's a keeper that the housing slides into. Pull the housing forward, then carefully reach in the back to disconnect the water lines. The slack created in the water lines earlier will allow you to reach the water line connections. The inlet water line comes in from the back. The water lines going to the freezer door hinge go through the floor of the compartment. Remove the retainers from the John Guest fittings and disconnect the water lines. Remove the housing and connect the water lines to the new housing. Reassemble the refrigerator.How a Sears Tech performs dishwasher maintenanceSears PartsDirect2023-09-18 | Maintaining your dishwasher will help it work efficiently and last longer.
The technician performs these steps to maintain a dishwasher: 1. Check the pump and motor underneath the dishwasher for leaks. 2. Check the pump area inside the dishwasher. 3. Clean the screens and filters inside the dishwasher. 4. Check the spray arms and proper water distribution. 5. Clean the dispenser and check its operation. 6. Check the heating element. 7. Ensure the correct amount of water enters the dishwasher. 8. Check for proper drain operation. 9. Check the door gasket for leaks. 10. Level the dishwasher. 11. Check for proper dishwasher operation. 12. Inspect the electrical ground and electrical connections. 13. Check for leaks whenever water enters the dishwasher. 14. Discuss what was checked and any problems found with the homeowner.
To schedule a Sears Technician to clean & maintain your dishwasher, schedule service online at www-development.searshomeservices.com/maintain/appliance-maintenanceHow to remove a riding mower blade belt #gardenequipment #mower #beltSears PartsDirect2023-09-18 | This #diy video shows how to remove the blade drive belt on a common riding lawn mower. The blade drive belt connects the engine pulley to the mower deck pulleys and spins the cutting blades. A worn blade belt won't spin the blades fast enough to cut the grass. A broken blade belt won't spin the blades at all. Examine the blade drive belt and replace it with a part that fits your model if you find damage or excessive wear.
Find riding mower parts at https://www.searspartsdirect.com/part...
Or click here to schedule an appointment with a repair technician. https://www.searshomeservices.com/rep...How to Replace Suspension Rods in a Kenmore or LG Top-Load WasherSears PartsDirect2023-09-12 | This #diy video shows how to #replace tub suspension rods in common LG and Kenmore Top-Load washing machines. The #washer suspension rods support the tub.
Unplug the washer before beginning the repair.
Servicing the new horizontal dampers is easy once you have the top cabinet cover open. Follow the instructions in the top cover access video and support the top cover as you work on the dampers and suspension rods. Disconnect power from the washer. With the top cover open, the horizontal damper can be removed by reaching in along the side of the tub. Use a 5/16-in or 8 mm, 12-point box end wrench to help you remove the horizontal damper retaining pin on the tub. Put the box end of the wrench over the lower end of the pin to depress the locking tab on the pin. While holding the wrench up against the bracket, push up on the pin and then lift it out from the top. The suspension rod end of the damper can then be released from the slider on the suspension rod using a small screwdriver. When reassembling the damper, make sure that the wide flange side of the bushing is facing up. If the other end is up, the pin may be difficult to remove in the future. To remove the suspension rod, the horizontal damper must first be disconnected either from the suspension rod slider or from the tub. Once the horizontal damper has been disconnected, lift the tub and suspension rod far enough for the upper end of the rod to clear the bracket on the corner of the cabinet. While holding the tub in position, lower the suspension rod to disengage it from the tub at the bottom. Lift out the suspension rod. To install the suspension rod, follow these steps in reverse order.
To cover all of your home appliances for one monthly fee with the Sears Protect appliance plan, visit your Sears Protect Home Warranty page tinyurl.com/Sears-Protect-Sign-Up . For more information about the Sears Protect plan, call us at 646-440-2437.How to fix a built-in wall oven that wont heat #diy #oven #repairSears PartsDirect2023-09-12 | This DIY repair video shows troubleshooting steps that you can take when your electric wall oven won't heat after running a self clean cycle.
Shut off the house circuit breakers for the wall oven before accessing the thermal switch shown in the video.
To have a Sears Technician diagnose and repair your wall oven, schedule in-home repair service at searshomeservices.com/repair/oven-repair-service .How to Remove the Top Cover on a Kenmore or LG Top-Load WasherSears PartsDirect2023-09-06 | This video shows how to remove the top panel or cover or common LG and Kenmore washing machines. Unplug the washer before beginning this #diy #repair procedure.
The washer model shown in the video is LG model WT56. The procedure is the same for model WT17 and many other LG and Kenmore washer models.
Transcript: Always unplug the washer prior to servicing it. Move the #washer out far enough to allow access for removing the 2 screws from the back of the top cover. One on each side. If the top cover is to be opened, the wiring harness ties must be released on the back of the washer to prevent damage to the wiring harness during service. The main wiring harness in this washer is anchored to the cabinet to protect it from damage during operation. The top cover cannot be opened without releasing the wiring ties. It is extremely important that the harness ties are remounted after service. Once the screws are removed, lift the rear of the top cover enough to clear the brackets on the cabinet. Slide the top cover forward until it stops. When you tip the top cover up, these brackets will fit down over the rear edge of the cabinet to support the cover. Lift the top cover clear of the brackets on each side of the cabinet. Slide the cover forward a few more inches then tilt the cover up so that the brackets on the back of the cover fit over the rear of the cabinet. Lean the cover against the wall, being careful not to damage the cover or the customer's property. To reassemble the top cover, all the brackets and anchors must be aligned. Side brackets on the cabinet fit into the slots on the sides of the top cover. The front tabs on the top cover engage with the brackets on the front of the cabinet. Lift the top cover so the rear brackets clear the cabinet and set it down on top of the cabinet so that it is aligned with the cabinet. Now, lift the rear of the top cover and slide the cover forward until the side brackets are engaged. This will result in the front tabs being in the proper position for engaging the front brackets. Slide the top cover to the rear until the back edge drops down over the cabinet brackets. The cover is now ready for the 2 screws to be installed. After remounting the top cover and before returning the washer to service, it is extremely important that the wiring harness is re-anchored to the cabinet. Remove the rear access cover and re-mount the harness ties that were released before opening the top cover.
Restore power to the washer by plugging the outlet cord back in. Move the washer back into place.
When you face a washer failure that you're not able to diagnose and repair on your own, schedule a Sears Technician to fix the washer online on our Sears Home Services website searshomeservices.com/repair .
Get a Sears Protect appliance warranty to cover all of your home appliances for one monthly fee. Get more information about the Sears Protect plan here tinyurl.com/yz4uj6tr .Washer Cycles Explained Permanent Press, Delicate and Speed Wash #washer #laundrySears PartsDirect2023-09-05 | This short video shows how to use 3 common washing machine cycles.
1: Delicate/Hand Wash
For: pillows, unmentionables and washable silk or lace How it works: slow, gentle cycle with low tumbling and spinning
2. Rapid/Speed Wash
For: your outfit for tonight How it works: shortened wash cycle with a powerful spin cycle
3. Permanent Press/Wrinkle Shield
For: synthetic fabrics, such as polyester and rayon How it works: medium-speed wash with a gentle spin cycle that reduces wrinkles
We help your appliances work harder and live longer.
When your washer isn't working properly, set ups service by a Sears Technician at searshomeservices.com/repair .
Get a Sears Protect plan to cover all your home's appliances. Learn more about a Sears Protect plan at tinyurl.com/yz4uj6tr .How to tune up a lawn mowerSears PartsDirect2023-06-19 | This #diy video shows how to #tuneup a #lawnmower . See the steps to take to keep your lawn mower in top shape.
1. Replace the spark plug. 2. Change the air filter. 3.Replace the oil. 4. Check the cutting blade and replace it if necessary.
Get 10% OFF parts -- use promo code YOUTUBEHow to Replace a Laundry Center Drain PumpSears PartsDirect2023-06-16 | This video #diy #repair video shows how to replace the drain #pump on common Kenmore and Frigidaire laundry centers.
If your washer doesn't drain, first check for a clogged washer drain or a kink in the drain hose. If the drain path is clear, you may need to replace the drain pump.
Visit us at https://www.searspartsdirect.com?sid=soc:youtube:how-to-replace-a-gas-laundry-center-drain-pump
Or call 1-800-437-1673 to speak with a parts specialist.
Transcript: If your washer doesn't drain, first check for a clogged washer drain or a kink in the drain hose. If the drain path is clear, the drain pump might have failed. If your pump won’t drain the water when activated, replace it using the steps in this video. Before you begin, wear work gloves to protect your hands. Unplug the laundry center. Shut off the gas. Remove the screws from the bottom of the front panel. Slide the front panel down to release the mounting tabs and pull it off. Place a towel under the pump to catch water from the hoses. Squeeze the hose clamps and pull the hoses off the drain pump. Disconnect the wires from the drain pump. Release the mounting tab and pull the plastic shield off the pump. Remove the pump mounting screws and pull out the drain pump. Position the new drain pump on the washer base and reinstall the mounting screws. Reinstall the plastic shield on the pump. Reconnect the wires to the drain pump. Reinstall the drain pump hoses and secure them with the hose clamps. Push the front panel mounting tabs into the mounting slots and slide the panel up to engage the mounting tabs. Reinstall the mounting screws. Plug the laundry center back in. Turn on the gas supply.How to Fix Your Riding Mower When it Wont Start Solenoid TroubleshootingSears PartsDirect2023-06-14 | This #diy #repair video shows how to troubleshoot and fix your riding lawn mower when you turn the key and don't hear the #solenoid click. If you do hear the solenoid click, watch this video to troubleshoot mower starting problems: youtu.be/ZLZA2P2bbYo Web page describing the repair: searspartsdirect.com/diy/article/riding-lawn-mower-engine-wont-turn-over-or-click-video Parts shown in the video: Solenoid -- searspartsdirect.com/part-number/192507/0071/917.html , Fuse -- searspartsdirect.com/part-number/STD391020/0098/980.html , Ignition switch searspartsdirect.com/part-number/532193350/0071/917.html , Brake switch searspartsdirect.com/product/16cni5baam-0071-917/id-176138 , Blade switch -- searspartsdirect.com/part-number/197802/0071/917.html .
Transcript: Today we're going to troubleshooting a riding lawn mower that doesn't do anything when you turn the key to start the engine—not even click. What is the significance of the click when you turn the key? When you hear the click, you know the starter solenoid coil is getting power from the battery through the ignition switch. If you don't hear that click, either the starter solenoid has failed or the starter solenoid coil isn’t getting power. To understand how we track down the problem, it helps to know how the starting system works. The positive, red battery cable connects to one of the two large terminal posts on the starter solenoid. The black wire connected to the other large terminal on the starter solenoid carries power to the starter motor to start the engine. A small red wire branches off the red solenoid terminal post to carry power through the ignition switch to the coil at the bottom of the starter solenoid. When you turn the key to the start position, the ignition switch sends power through the white wire and energizes the coil inside the solenoid. The coil closes an internal contact to send power from the red battery cable to the black wire, which powers the starter motor to spin the engine. So what can go wrong with the starting system? Well, a dead battery won't power up the starter system and could prevent the solenoid coil from clicking. To check the battery, we’ll use a multimeter to measure the DC voltage across the battery terminals. With the multimeter set to measure DC voltage, touch the red multimeter probe to the positive or red battery terminal and the black meter probe to the negative or black battery terminal. If the battery is good, it measures more than 12 volts DC. If it measures less than 12 volts, the battery is weak or dead and you've likely found the problem. A weak or dead battery won't power the starter solenoid coil. If the battery is okay, it means power is getting to the red battery cable. But, is voltage getting through the red battery cable to the red terminal post? To check that, let’s measure voltage at the red terminal post. With the multimeter set to measure DC voltage, touch the red meter probe to the red post on the starter solenoid and the black meter probe to the negative terminal on the battery. It should measure more than 12 volts. If the meter measures less than 12 volts, check the battery terminals and cable leads for corrosion. Clean corrosion off the battery terminals and battery cable leads with a wire brush—corrosion can prevent the red solenoid post from getting power. Recheck the voltage. If it still doesn’t measure more than 12 volts at the red post, replace the red battery cable. Now that we know the red terminal is getting power, the next step is to find out whether the solenoid coil gets power when you turn the key. If you measure voltage at the coil but the internal contact doesn't click, the starter solenoid is to blame. The solenoid clicks when it sends power to the starter motor. To check voltage on the solenoid coil wires, you need clip-on meter probes to hold the probes on the wires as you turn the ignition key, unless you have a helper to turn the key while you hold the probes on the wires. Pull the white and black wires off the spades of the solenoid. Set the multimeter to measure DC voltage. Clip the red meter probe to the white wire female spade connector and the black meter probe to the black wire female spade connector. Turn the ignition key to the start position, note the voltage reading on the meter display and then turn the ignition key off. If the multimeter measures battery voltage, it will be more than 12 volts. Replace the starter solenoid because the coil is getting power but not closing the internal contact to send power to the starter motor. Here's a video that shows you how to replace the starter solenoid. If it measures 0 volts, there’s a break in the circuit to the solenoid coil. The starter solenoid is likely okay, it's just not getting power. Time to test the coil circuit. We'll check the ground side of the circuit first. The black wire attaches to the solenoid coilHow to get rid of fridge smellsSears PartsDirect2023-06-13 | This #diy video shows #odorcontrol tips for your #refrigerator .
Step 1: Empty out your fridge. Step 2: Check expiration dates. Step 3: Toss old leftovers and expired items. Step 4: Mix water and white vinegar and give your fridge a good scrub. Your fridge will smell fresher than ever!
Have a Sears Technician perform professional maintenance and cleaning on your refrigerator. Schedule Clean & Maintain service searshomeservices.com/maintainHow to Replace the Axle Seal on a Riding Mower with a CVT RS800 TransmissionSears PartsDirect2023-06-13 | This #diy repair help video shows how to #replace the axle seal on a General Transmission brand CVT RS800 riding mower #transmission . Follow the tips in the video to remove and replace a leaking axle seal.
Save 10% OFF parts -- use promo code YOUTUBEHow to Prevent BBQ Grill Flare-UpsSears PartsDirect2023-05-26 | This short #bbq video provides helpful #tips on how to prevent flare-ups when #grilling . Clean or replace the flame tamers on your grill to prevent grease build-up. Clean the grease tray at the bottom of the firebox. Use indirect heat to cook fatty foods.
Get 10% OFF parts -- use promo code YOUTUBEHow to Fix a Dishwasher that Tilts Forward When You Open the DoorSears PartsDirect2023-05-26 | This #diy video shows how to #fix your #dishwasher when it tilts forward as you open the door. The dishwasher has brackets that secure it to the cabinet. When the brackets get disconnected or break, you'll need to reattach the bracket to the cabinet or install and attach new brackets.
See the full video for fixing a dishwasher that tilts forward here youtu.be/wyT7Wvvlxjg
You can order replacement brackets from our Sears PartsDirect website. searspartsdirect.com
Get 10% OFF parts -- use promo code YOUTUBE
If you need to have a Sears Technician repair your dishwasher, schedule service online at searshomeservices.com/repair/dishwasher-repair-serviceHow to clean AC condenser unit finsSears PartsDirect2023-05-24 | This #diy video shows how to clean the fins on the outside condenser unit of your central air conditioner. Follow these #expert tips to clean the fins without damaging the fan motor.
Shut off the house circuit breaker for the unit before cleaning the condenser coil fins.
To have a Sears Technician clean the condenser coil fins and also clean and maintain the entire central air conditioner, schedule Clean & Maintain service for your AC. searshomeservices.com/maintain/heating-cooling-maintenanceHow to Fix Your Dishwasher When it Wont Drain After Installing a New Garbage DisposalSears PartsDirect2023-05-15 | This #diy #repair video shows how to fix your #dishwasher when it won't drain after installing a new garbage disposal without removing the disposal knock-out plug. The short video shows how to remove the garbage disposal knock-out plug so that your dishwasher will drain properly.How to Rebuild a Lawn Mower CarburetorSears PartsDirect2023-05-12 | This #diy #repair video shows how to clean and repair a lawn mower #carburetor . You'll need to clean and rebuild the lawn mower carburetor when it leaks gas, the engine won't start, the engine runs rough or when the engine starts and runs briefly then stops.How to Adjust Valves on a Briggs & Stratton Twin Cylinder EngineSears PartsDirect2023-05-11 | This #diy #repair video shows how adjust valve lash on a twin cylinder Briggs & Stratton riding mower engine.
When the engine cranks but won't start, you may need to adjust valve clearance. For Briggs & Stratton engines, you'll need to find top dead center of cylinder motion and go 1/4-inch past that position to adjust valves accurately.
To have a Sears Technician repair your riding mower, schedule service at searshomeservices.com/repair/riding-mower-repair-serviceHow to Replace the Friction Pack on the RS800 CVT TransmissionSears PartsDirect2023-05-11 | This #diy #repair video shows how to replace the friction pack on a common RS800 CVT transaxle made by General Transmission. You'll need to replace the friction pack for loss or neutral or loss of drive in the riding mower.
Transcript: The next repair that we’re going to do is to replace the friction pack. This is on a fender-shifted unit with either a loss of neutral or loss of drive. To replace the friction pack, we must remove the driven kit and the drive kit – and we refer to other videos for those repairs (remove the driven kit -- youtu.be/i5ezGhkOdWw and remove the driver kit -- youtu.be/qhwhnjR_S-Y ). We’ve now removed the driven kit and the drive kit so now we’re going to remove the top cover, C-clips, shift arm and the friction pack. We remove all of the screws. We remove the C-clip, shift arm and the cover. There are 4 screws holding the friction pack. The best way to reach the one under the cam is to simply rotate this out of the way to get access. To get access to the bolt, we must remove the spring. You’ve got to rotate the cam. Then the friction pack comes off. The new friction pack is shipped with the pin. Training Bulletin TB71-59 will explain the removal of the pin (TB71-59 instructs you to set control lever in Neutral and connect the control arm to the transaxle – YOU MUST REMOVE THE SHIPPING PIN IMMEDIATELY AFTER ATTACHING THE CONTROL ARM – DON’T LEAVE THE SHIPPING PIN IN PLACE OR YOU WILL DAMAGE PARTS). At this time, we reinstall the friction pack. Tighten the screws. Reassembly starts with the cam holding the selector. It slides into place. Then reset the spring. The measurement between the spring must be 2.5 inches. The next step is the cover. Tightening torque should be 2.5 ft-lbs. Reattach the shift lever. Install the C-clip. Remove the pin. We have now reinstalled the drive kit and the driven kit.How to Replace a Broken Brake Lever on the RS800 CVT Transaxle of a Riding MowerSears PartsDirect2023-05-11 | This #diy #repair video shows you how to replace a broken brake lever on a common RS800 CVT #transmission found in many riding mowers and lawn tractors. You'll find this transaxle in riding lawn mower brands such as Craftsman, MTD, Husqvarna, Troy-Bilt, Toro and John Deer.
Transcript: The next failure we're going to look at is a loss of brake. In this case we did find that the brake lever itself is broken. The brake lever, you'll notice, has 2 holes on the end. Ours does not have that. So, we're going to disassemble the unit. We have to go under the case to replace the brake lever. So, we're going to start by removing the drive unit with a T-25. This is also a good time to check the function of the CVT. You want to make sure that you have springs and that it does move freely. Once the drive unit is out, we'll set it aside. The next step is with a T-20, we're going to remove these 3 screws on the driven unit. Remove the cap. To remove the next piece, we've got to press down to release the spring pressure and pull out the pin. Remove the base. The next step is that we've got to remove this nut. This is held in place with 65 ft-lbs. You will need the tool from General Transmissions to remove this nut. Retain the pin. There's also a washer. Remove the cover. The next step is to remove the unit -- be careful, there are 8 roller bearings and a spring. Again, with the T-25 wrench, we're going to remove the cover bolts. The 2 top cover bolts also have washers. Then the cover just lifts off. Here is the brake lever that we're going to be replacing -- you can see that it is broken and the spring is not attached. With the T-25, we're going to remove the 2 screws. With a flat screwdriver we're going to pry gently on the bottom side of the brake lever. It lifts off. When replacing the brake lever, make sure that the O-ring is in place. It simply slides down and taps into place. This time we're going to reinstall the spring. It goes in the 2nd hole and over this post. This is also a good time to make sure that you're centered -- this spring is centered here and that your orientation of the CVT is in the right location. We're simply going to put the cover back on, the driven unit back on and the drive unit back on. The 2 top bolts have washers. Our next step is the spring, the cover with the ball bearings and the cover. At this time, we're going to reuse the pin and the tool from General Transmissions. We're going to torque the nut to 65 ft-lbs. Install the riser plate, spring and cover. At this point we have to depress the spring. Install the pin and the cover. The 3 T-20 screws go in next. Torque to 1.5 ft-lbs. of pressure. Next, we install the belt and the drive kit, making sure we have the belt keeper to the outside and speed screw to the outside. Then we're going to reinstall the T-25 bolts using blue Loctite and 2.5 ft-lbs. of torque. At this time we reattach the spring to the brake pedal.Riding Mower Only Moves in Reverse No Forward MotionSears PartsDirect2023-05-11 | This #diy #repair video shows what to do when your riding lawn mower only moves in reverse but won't move forward when you shift the control to move in the forward direction. Learn how to fix a common RS800 CVT #transmission on riding mowers and lawn tractors when the mower won't move forward. When you need parts, visit us at: https://www.searspartsdirect.com?sid=...
Or call 1-800-437-1673 to speak with a parts specialist.
To schedule an appointment with a repair technician. https://www.searshomeservices.com/rep...How to Fix Your Dishwasher When it Wont FillSears PartsDirect2023-05-10 | This #diy #troubleshooting video shows what to do when your dishwasher won't fill. Find #repair tips to help you get your dishwasher going again. Close the dishwasher door fully so the cycle can start. Make sure the water supply valve is open. Check for items under the mushroom float switch.
Visit us at: https://www.searspartsdirect.com?sid=...
Or call 1-800-437-1673 to speak with a parts specialist. To schedule an appointment with a Sears Technician, schedule service at searshomeservices.com/repair/dishwasher-repair-serviceHow to Start Your Lawn Mower Using Starter FluidSears PartsDirect2023-05-10 | This #diy #repair video shows how to use starter fluid on your lawn #mower to test the engine and/or start the engine.
If your lawn mower won't start, this test will help you find the cause.
Remove the air filter. Spray some starter fluid directly into the carburetor. Try to start the engine.
If it starts and runs briefly, you have a fuel or air supply problem.
Drain and replace old fuel.
Install a new air filter.
If the engine didn't start, watch our full troubleshooting video to learn more.
youtu.be/qzkyFOq1NeEHow to Fix a Refrigerator Ice Dispenser that Just Clicks (Kenmore 253 and Frigidaire Models)Sears PartsDirect2023-05-10 | This #diy #repair video shows how to #fix a common ice dispenser in Kenmore 253 Series, Frigidaire and Electrolux refrigerators when the ice dispenser just clicks when you press the dispenser lever. When this happens, the control rod linkage going to the flapper solenoid has likely become disconnected. This video shows how to disassemble the dispenser and reconnect the control rod linkage.
Transcript: We have been receiving complaints where ice does not dispenser properly on certain Frigidaire, Electrolux or Kenmore 253 refrigerator models. This condition is observed when the paddle is depressed. The ice door opens for split second then closes immediately. The sound is very distinctive. There is no delay in the flapper closure as there should be. Most likely, the solenoid linkage has fallen out of place. The repair will require the dispenser module to be removed and an adjustment to be made. Begin by disconnecting power to the refrigerator. Remove the module cover by pulling it forward -- beginning at the bottom and working your way around. Remove the 2 screws that hold the control housing in place. Tilt it forward, disconnect the wire harness and set it aside. Remove the 2 screws holding the dispenser module and loosen the water tube in the retainer. Pull it forward and rotate the module to gain access to the right-hand side. You can see that the metal rod is out of place as it should be inserted on the back side of the gray plastic linkage arm. Insert a small flat-blade screwdriver behind the brass tab and twist the screwdriver. This will put a little more tension on the metal rod to hold it in place. Then, using the small screwdriver, push the rod back into the plastic linkage. Test the operation by manually pulling in the solenoid once to open the flap, then once again to close the flap. Repeat this just to make sure it is functioning properly. Reinstall the module. You will need to lift up slightly to place the rear portion of the module above the ledge on the door mold. Reengage the water tubing into the retainer. Ensure that the flap is sealing properly. Reinstall the control housing and the module cover. Reapply power and test the operation. Notice the difference in sound and the delay in the flap closing as it is operating correctly.
If you have broken parts in the dispenser, you can find replacement parts at searspartsdirect.com
If you need to have your refrigerator repaired by a Sears Technician, schedule service at searshomeservices.com/repair/refrigerator-repair-serviceHow to Replace the Driven Unit in a CVT Transmission of a Riding MowerSears PartsDirect2023-05-05 | This #diy video shows how to #replace the Driven Unit in a RS800 CVT #transmission of a riding lawn mower or lawn tractor.
The Driven Unit is rotated by the drive pulley and spins gears inside the transmission to move the wheels.
Transcript: The next repair that we're going to look at is loss of drive -- and we've traced the problem to the driven unit. So we're going to replace the Driven Unit. The Driven Unit comes in a kit. It has the cover, the ramp, the base and the cover. It also comes with the spring, a new nut and washer, and 3 new screws. To begin, we have to take off the drive unit. We do that with a T-25 Torx driver. Remove the 4 screws. Next, we have 3 T-20 screws on the cover. To remove the pin we have to relieve the spring pressure by pressing down. The pin will slide out. Next, we reuse the old pin and the tool from General Transmissions searspartsdirect.com/product/19x5wm79vj-0071-537/id-gt79252 . We're going to remove the nut. This is held in place at 65 ft-lbs. Remove the nut and the washer. Remove the cover. Take care not to loose the ball bearings. Remove the spring. When reassembling, we're going to use the new parts from the kit. Start with the spring. We reuse the ball bearings. We're going to install the new cover, then new washer and new nut. For this operation we're going to use the old pin. Use the tool from General Transmissions. Torque the nut to 65 ft-lbs. Discard the old pin. Install the ramp from the kit, the new spring from the kit, and the new pin from the kit. To install the pin we have to relieve the spring pressure. Then reinstall the cover. Next, we install the belt and the drive kit, making sure that we have the belt keeper to the outside and the speed screw to the outside. Then we're going to install the T-25 bolts using blue Loctite and 2.5 ft-lbs. of torque. And the repair is finished.
If you need to have a Sears Technician replace the Driven Unit, schedule service at searshomeservices.com/repair/riding-mower-repair-serviceHow to Connect Jumper Cables to a Riding MowerSears PartsDirect2023-04-28 | This #diy video shows hot to connect #battery #jumper cables to a riding mower or lawn tractor. Transcript: First, connect one end of the red jumper cable to the positive terminal on the mower battery. Connect the other end of the red cable to the vehicle's positive battery terminal. Don't let the other end of the red cable touch any metal. You'll see a lot of sparks and could damage the good battery. Next, connect the black jumper cable to the vehicle's negative battery terminal. Then connect the other end of the black jumper cable to the metal mower frame away from the fuel tank and battery. Turn the ignition key and start the mower engine. Now disconnect the jumper cables— in the right order. Disconnect the black cable from the mower frame first and then disconnect the black cable from the vehicle's battery. Next, disconnect the red cable from the vehicle's battery and then disconnect the red cable from the mower's battery.How to Keep a Zero-Turn Mower from Creeping in NeutralSears PartsDirect2023-04-27 | This #diy #repair video shows how to #fix a zero-turn rear-engine riding lawn mower that creeps forward or backward when the motion control levers are in the neutral position.
Transcript: Loosen the lug nuts on both rear wheels, but don’t remove them. Place wheels chocks in front of and behind the front castor wheels. Jack up the back of the mower to lift both back wheels off of the ground. Place jack stands under both sides of the rear frame to support the mower. Remove the lug nuts from the rear wheels and pull off both wheels. On the side with the moving wheel hub, remove the linkage mounting screw and pull the linkage off of the bracket. Loosen the neutral adjustment screw. Adjust the control bracket to stop the wheel hub from moving. Tighten the neutral adjustment screw. Reconnect the control linkage. Reinstall the rear wheels on the hubs. Reinstall the lug nuts and finger tighten them. Jack up the back of the mower and remove the jack stands. Lower the mower to the ground. Remove the front wheel chocks. Set your parking brake and firmly tighten the lug nuts on the rear wheels.
If you need repair parts for your riding mower, visit us at: https://www.searspartsdirect.com?sid=...
Or call 1-800-437-1673 to speak with a parts specialist.
If you need to have a Sears Technician repair or adjust your riding mower, schedule an in-home repair appointment on our Sears Home Services website. https://www.searshomeservices.com/rep...How to Clean Your AC Condenser CoilsSears PartsDirect2023-04-27 | This helpful #diy video shows how to #clean the air conditioner condenser #coils .
Cleaning the AC condenser coils helps the central air conditioner run more efficiently and cool better.
Spray the coils using a garden hose sprayer monthly during spring and summer to keep your central AC running efficiently.
Have your central air conditioner professionally cleaned and maintained every spring by Sears Home Services. Schedule your Spring AC Maintenance Service now searshomeservices.com/maintain/heating-cooling-maintenanceHow to Organize Your KitchenSears PartsDirect2023-04-26 | This video shows expert #tips to help you #organize your #kitchen .
Keep items stored smartly so you can easily reach them when needed.
Kitchen Cabinet Organization Tips
Keep less-used items on higher shelves.
Put dry goods in clear containers.
Store spices away from heat sources, which can cause them to lose freshness.
Use a lazy Susan to see what you have with a quick spin.
Hang utensils to save drawer space.
Use bins and baskets to organize smaller items.
Organize pots and pans in pull-out shelves.
Use adjustable cookware organizers to keep pans and cookie sheets neat.
For more kitchen and home appliance tips, visit searspartsdirect.com/diy/repair-helpHow to Help Food Last Longer in the FridgeSears PartsDirect2023-04-25 | This #helpful video shows 5 ways to help keep items #fresh for longer in the #fridge .
There’s nothing more frustrating than seeing your food go bad in the fridge, especially if you just purchased it. What gives? Well, it may have something to do with how you’re storing your food. Whoops!
The good news is that there are a lot of surprisingly simple ways to extend the life of your groceries. Here, we have identified five genius hacks to help ensure that berries, avocados, apples, lettuce, bread and cheese will stay fresher for longer.
Apples and Avocados: Squeeze lemons on them. Cheese: Wrap in parchment paper. Bread: Cover in a kitchen towel and place in a paper bag. Berries: Don't rinse until you're ready to eat them. Lettuce: Store in plastic bag lined with paper towels and keep it in the high-humidity crisper drawer.
Need help with a repair? Call Sears Home Services at 1-800-949-7191 or click here to schedule service now: http://bit.ly/2jq33lTHow to Install a Washer Drain HoseSears PartsDirect2023-04-25 | This #diy video show how to #install the drain hose on a #washer . Follow the tips shown in the video to make sure that the drain hose is properly in stalled on your washer so the washing machine drains properly.
For professional repair help, contact Sears Home Services. We are #1 in appliance repair and the nation's largest, most trusted service provider. Sears repairs all major washer brands, so no matter where you bought your appliance, we can help fix it.
Call the Sears Blue Service Crew at 1-800-949-7191 or just click here to schedule service now: http://bit.ly/1IHoiSwHow to Organize Your RefrigeratorSears PartsDirect2023-04-25 | This video shows how to #organize your #fridge . Get helpful #tips on what to put on each shelf and in each drawer of your refrigerator.
Help your food AND your fridge last longer.
Top Shelf: leftovers, yogurt, dips & beverages
Lower Shelves: raw meat, eggs & dairy
Meat Drawer: deli meat & cheese
Crisper Drawers
Low Humidity: produce with a skin — apples, pears, berries & tomatoes
High Humidity: leafy greens & fresh herbs
Fridge Door: condiments & salad dressing
We help your appliances work harder and live longer.
Need help with a repair? Call Sears Home Services at 1-800-949-7191 or just click here to schedule service now: http://bit.ly/1IHoiSw Or give us a call at 800-275-8029.
Transcript: Hi, this is Wayne with Sears Parts Direct. Is your central air conditioner not keeping things as cool as it should be? Here’s something to check before you make that call for service. Many central air conditioners have a drain float switch that shuts the system down if the drain is clogged and water backs up under the evaporator. If this switch trips, the air conditioner will shut down to avoid water damage. If this well under the switch is full, then it's time to unclog the drain line. You may be able to remove the clog with a shop vac. If not, you can use a plumber's snake to clear the drain line. To keep this thing from clogging up in the future, pour a cup of liquid bleach down the drain vent tube every month. The bleach kills mold and mildew that can build up inside the drain pipe and hose. To keep from killing the grass in your yard, stick a pan under the drain hose outside to catch the bleach as it runs out. And always remember to protect your eyes and skin when handling bleach and other harsh chemicals. You can get in the habit of doing this at the same time you change your air filter.How to Remove a Frigidaire Frontload Washer Door BootSears PartsDirect2023-04-17 | This #diy video shows how to #remove the rubber door boot on a Frigidaire front-load #washer .
Get 10% OFF parts -- use promo code YOUTUBE to order a new door boot at searspartsdirect.com .
Unplug the washer before beginning the repair. Shut off the water supply.
Transcript: This video will cover the removal of the bellow. Please note that this process can be done with the front panel installed. For demonstration purposes, we show some footage without the front panel in place. To remove the bellow, start by pulling back the bottom of the bellow slightly and using a pair of needle-nosed pliers to remove the spring loop. Next, cut this cable tie and remove the advanced rinse technology (or ART) hose from the bellow. Next, remove the LED light assembly from the bellow. Then, reach underneath the bellow and remove the 2nd spring loop and pull the spring loop out. The bellow can then be removed.
To have a Sears Technician remove and replace the bellow, schedule washer repair service: searshomeservices.com/repair/washer-repair-serviceHow to Replace the Drive Belt on a Snapper Lawn MowerSears PartsDirect2023-04-17 | This #diy video shows how to #replace the rear wheel drive belt on a Snapper lawn #mower . Save 10% OFF parts -- use promo code YOUTUBE at searspartsdirect.com .
Transcript: To replace the drive system belt, begin by removing the spark plug wire. Remove the bag or mulch plug. Raise the height of cut to its highest position. Tip the unit onto its side and remove the blade. Locate and remove the 2 baffle retaining screws near the trailing shield. Locate and remove the 4 screws that retain the baffle to the deck. Remove the belt cover retaining screw from just behind the engine. Carefully remove the baffle and belt guard. Loosen the 2 drive pulley belt guards and swing them aside. Carefully remove the belt from the engine pulley. Unhook the cable spring from the transmission. Rotate the transmission down. Remove the belt guard. Remove and replace the belt at this point. Reassemble in reverse order. Upon reassembly, position the belt guards 3/32-inch away from the engine pulley. If the system appears to be slipping uphill, an adjustment is present near the left, rear wheel. Simply turn it clockwise to increase cable tension to resolve belt slipping concerns.How to Replace Riding Mower Fuel Filter 25-050-08-SSears PartsDirect2023-04-10 | This diy# video shows how to #replace riding mower fuel filter #part number 25-050-08-S.
Transcript: Before attempting to remove the fuel filter, run the tractor until all the fuel has been consumed and the tank is empty.
Caution: Work in a well-ventilated area.
To begin, use pliers to release tension on the tension clamps and move the clamps away from the fuel filter.
Remove the fuel filter from the fuel hoses.
Caution: It is best to have a cloth in position for residual fuel that will be lost when the fuel filter is separated from the fuel hoses.
Locate the arrow on the new fuel filter and install that end toward the engine carburetor.
Install the other end of the fuel filter to the remaining fuel hose.
Use pliers to position the fuel hose retaining clamps to lock the fuel hoses to the fuel filter.
Clean any spilled fuel.
Warning: Undertaking repairs to appliances can be hazardous. Use the proper tools and safety equipment noted in the guide and follow all instructions. Do not proceed until you are confident that you understand all of the steps and are capable of completing the repair. Some repairs should only be performed by a qualified technician.How to Drain Oil from a Riding Lawn MowerSears PartsDirect2023-04-10 | This #diy video shows how drain oil from a common riding lawn #mower or lawn tractor such as a Craftsman mower. The #engine shown in the video is a Kohler model. Follow the steps shown in the video attach the clear drain tube and open the drain valve to drain the oil out of the engine.
The oil drain tube is part number 148456. Here's a link for the part: searspartsdirect.com/product/8751fh9w66-0071-917/id-148456Dont Use Compressed Air to Clean an Engine Air FilterSears PartsDirect2023-04-10 | This video shows why you shouldn't use compressed air to clean an #engine air filter. Compressed air will damage the #filter media so dirt and debris will enter the engine and cause #damage .
Remove the air filter and tap it to remove and debris between filter replacement.
The air filter shown in the video is for a riding mower or lawn tractor.
When you need to replace the air filter on your lawn tractor or riding mower, order the parts from our Sears PartsDirect website: searspartsdirect.com
When your riding mower or lawn tractor needs repair, schedule repair service here: searshomeservices.com/repair/riding-mower-repair-serviceHow to Clean and Maintain Your WindowsSears PartsDirect2023-04-04 | This video shows how to clean your #windows and #maintain them for the benefit of your #home . Windows aren’t only a sizable investment, they’re a big part of the curb appeal of your home. It’s likely time to give your windows some much-needed TLC.
When warmer weather comes around, it’s a great time to do some work on your windows. Maintaining your windows will not only help protect your investment but will also beautify your home.
Here are some tips and tricks for easy window maintenance.
1. Make a DIY Cleaner Combine 2 cups of water with 1/4 cup vinegar and 1/2 teaspoon of dish soap.
2. Use a sponge brush It's the perfect fit for tough-to-clean (and often-neglected) window tracks.
3. Deal with drafts Touch up your windows with caulk to help prevent drafts and cut down on energy bills.
4. Spot-check the seals If moisture accumulates between the panes, you've got a problem with the seal. Your window likely needs replacing.
5. Search and destroy rot If you have wood frames, scrape out rotted bits and fill with epoxy putty.
6. Think vinyl If you're replacing windows, vinyl doesn't need to be painted and won't warp or crack. Plus, cleaning is a breeze!
FOLLOW SEARS HOME SERVICES FACEBOOK ➜ Sears Home Services http://on.fb.me/1Q5aDNQ TWITTER ➜ @SearsHomeExpert http://bit.ly/2bCu1D1 GOOGLE+ ➜ Sears Home Services http://bit.ly/2bR6k7A PINTEREST ➜ Sears Home Expert http://bit.ly/2c4IhUK3 More Air Conditioner Myths BustedSears PartsDirect2023-04-03 | This video shows 3 more air conditioner #myths that just aren't true. Learn more about your central air conditioner and how to keep in top shape.
Myth #1: Turning the system off when you leave the house is a waste of energy.
BUSTED! It always saves energy to shut the system off when you’re not using it.
Myth #2: Close the vents in empty rooms to increase efficiency.
BUSTED! This can increase air pressure in the ducts, causing leaks at the vent seams.
Myth #3: The thermostat’s location doesn’t matter.
BUSTED! Putting it too close to vents or windows can cause it to turn on or shut off prematurely.
Schedule your HVAC Preventive Maintenance Check today. ➜ http://bit.ly/2dxAW3K3 Central Air Conditioner Myths BustedSears PartsDirect2023-04-03 | This video covers 3 top #hvac myths and reveals the real truth about your air conditioner.
Myth #1: You only have to change the air filter once a year. BUSTED! Change it every few months.
Myth #2: The bigger the system the better. BUSTED! A system that’s too big will cycle on and off too often. It’ll cost you — and shorten the life of the unit.
Myth #3: An energy-efficient unit = instant #savings . BUSTED! Check for leaky window seals or poor insulation.