It has its roots in the 1930s and was originally created with triode vacuum tubes to extend the high-end frequency response of video amplifiers.
This is the introductory video explaining the WHY behind this configuration and the HOW it works behind its operation.
In the next video I wil be showing you how to design one and demonstrating the benefits of this configuration both in the simulation world and with a bench experiment.
---------------------------------- Time Markers for Your Convenience ---------------------------------- 00:05 Initial Comments and Introductions 01:26 Device Capacitances 03:42 What is the Miller Effect? 05:35 The CASCODE Amplifier's Architecture 06:42 How does it work? 09:03 Parting Comments and Toodle-Oots
BJT Circuit Analysis: The CASCODE Amplifier (Pt 1) (066g1)Electronics for the Inquisitive Experimenter2024-07-10 | Here is yet another configuration of bipolar junction transistors called the CASCODE Amplifier.
It has its roots in the 1930s and was originally created with triode vacuum tubes to extend the high-end frequency response of video amplifiers.
This is the introductory video explaining the WHY behind this configuration and the HOW it works behind its operation.
In the next video I wil be showing you how to design one and demonstrating the benefits of this configuration both in the simulation world and with a bench experiment.
---------------------------------- Time Markers for Your Convenience ---------------------------------- 00:05 Initial Comments and Introductions 01:26 Device Capacitances 03:42 What is the Miller Effect? 05:35 The CASCODE Amplifier's Architecture 06:42 How does it work? 09:03 Parting Comments and Toodle-OotsMeasuring High Current with a Low Current Ammeter: The Art of Adding a Shunt Resistor (019d_v2025)Electronics for the Inquisitive Experimenter2025-09-10 | You have a low amperage analog ammeter in your hand and you want to be able to measure higher currents with it.
In this video you will learn how to create a home grown, higher amperage ammeter from that low amperage meter bu adding a shunt resistor.
I will step you through the process from the beginning to end using my own 50 microamp meter as the guinea pig. I will create a 250 milliamp meter out of it.
---------------------------- Time Marker Notes 00:05 Introduction 00:50 Preliminaries & What are we doing? 02:18 The Basis of how this works 03:01 Resistor Calculation - the easiest way... 03:23 Calculate the Voltage across the Meter Movement 03:54 Calculate the Current through the SHUNT resistor 04:28 Calculate the Value of the Shunt resistor 05:19 Calculate the Power Dissipation of the Shunt resistor 06:15 Finding an Off-the-Shelf resistor 07:37 Build my own Shunt resistor 10:34 Measuring my Shunt resistor's value 10:56 Setup 13:06 Making the measurements. 13:53 Calculate the value from measured values 15:03 Testing your Design 15:04 Zero your meter 15:16 Install the Shunt resistor 15:25 You *could* locate the Shunt remotely! 15:47 Measurement setup 16:39 Test Connections 17:16 Making the measurements 18:21 Evaluate the results 19:16 Final comments & toodle-ootsDissipation Factor, Q and Power Factor in Capacitors (081a)Electronics for the Inquisitive Experimenter2025-09-03 | Back in April of 2023 I released a video on the wild world of the Q-Factor. If you missed that video, there is a LINK down below for you. Q Factor relates to both inductors and capacitors, yet, when you look at the datasheet for a capacitor, you will rarely find a specification for its Q. Most times you will find data on a capacitor’s Dissipation Factor and sometimes on its Power Factor. But almost never its Q. What are these things and how do they relate to Q? These are the questions I answer here in this video. To do this, I have to provide a little background into both the Ideal and Real-Life capacitors. I develop a basic model of a real-life capacitor so we can understand where Dissipation Factor, Q and Power Factor come from. I also spend a little time in three different datasheets so you can have an idea what to look for. ======================================= LINK: VIDEO on Q, the complete story youtu.be/M6Ip1qkc8EM
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:18 The Ideal Capacitor 03:17 The Real Capacitor 04:15 A Basic Model 06:53 In Practice 08:14 Dissipation Factor 10:14 Q as it relates to Dissipation Factor 11:29 Power Factor 13:47 The Datasheets 13:47 Dissipation Factor & Q 15:44 Power Factor 16:50 Final Comments and Toodle-OotsHow to Characterize an Ammeter: Internal Resistance & Full-Scale Current (019c_v2025)Electronics for the Inquisitive Experimenter2025-08-27 | You have an old analog ammeter in your hand and are wondering what you can do with it. In order to use that Analog Ammeter to do stuff, you need to know two particular things about it.
In this video I am going to show you how to determine the two things you need to know about that ammeter: 1. Its Internal Resistance 2. Its Full-Scale Current
I will show you how to * measure higher currents * measure voltage with a properly characterized ammeter in my next two videos in this series. ---------------------------- Time Marker Notes 00:05 Introduction 01:53 Preliminaries ... What you need 03:26 What we are going to do here 03:46 ZEROING the meter before we begin 05:25 1. Determining the Internal Resistance 07:04 1.a. Establish full-scale indication 09:23 1.b. Measure applied voltage 09:44 1.c. Install parallel variable resistor 10:09 1.d. Adjust resistor for half-scale indication 12:07 1.e. Measure your resistor values 13:11 1.e.1. Measure resistance OFFEST 13:30 1.e.2. Measure Series Resistor value 13:51 1.e.3. Measure Parallel resistor value 14:10 2. Calculate Internal Resistance and Full-Scale Current 14:52 2.a. The REAL series resistor value 15:29 2.b. The REAL parallel resistor value 16:14 2.c. Full-Scale Current calculation 18:03 2.d. The Characteristics of this Ammeter 18:22 Conclusions and Final CommentsBLOOPER1Electronics for the Inquisitive Experimenter2025-08-20 | Someone asked for bloopers ... I thought you'd get a chuckle out of this. When the video on Dissipation Factor, Q and Power Factor comes out on September 3, you will recognize this line!Measuring FM Deviation using the MIN/MAX Method and the tinySA (080a)Electronics for the Inquisitive Experimenter2025-08-20 | On July 20, 2022 I released a video showing how to measure the FM deviation of transmitter using what I call the MIN/MAX method and my Rigol bench Spectrum Analyzer. Since that time, the tinySA has made a major debut in the experimenter's world. I was asked to show folks how to measure the FM deviation of a transmitter using the MIN/MAX method and this new, very cool, tinySA. That is what *this* video is all about.
LINK to the Spectrum Analyzer How To Video (029c) youtu.be/gPUqWXEWI94 ======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:22 SETUP: Power Limitations 02:24 Four ways to connect the transmitter to the tinySA 02:29 WAY #1: Air-to-Air 04:30 Way #2: Load-to-Air 05:47 Way #3: Power Attenuator 07:02 Way #4: Signal Sampler 07:45 Radio Setup 08:28 Calculate the Required Attenuation 08:59 What is the anticipated signal level? 09:26 tinySA Setup 09:26 Introduction 09:49 Frequency Related Settings 12:30 Define the Traces 13:41 Define the Markers (aka: Cursors) 15:39 Define the Math 16:53 Perform the Test 17:53 Determine the Results 19:43 Final Comments and Toodle-OotsIs it a Voltmeter or Ammeter? That is the question! (019b_v2025)Electronics for the Inquisitive Experimenter2025-08-13 | You have an old analog meter in your hand that has a voltage scale on it. Is it a true voltmeter or is it an ammeter that was part of a voltmeter? Before you can do much with it, you have to find the answer to this question. But, how do you do that?
In this video I am going to show you a method for determining if that meter is a voltmeter or an ammeter. There may be other ways of doing this, but this one has always worked for me.
---------------------------- Time Marker Notes 00:05 Introduction 00:52 Note your voltage scale(s) Equipment Needed: 01:44 A variable voltage power supply 01:54 A variable resistor Preparation 02:19 Set variable resistor to its maximum value 02:33 Set power supply output to zero volts 02:39 Connect everything up 03:10 The Procedure 03:12 Turn on the Power supply 03:18 Slowly increase the voltage while watching the meter. 04:01 Decrease Series Resistance 06:08 How do you know what you have? 06:49 Concluding commentsImpedance Matching (Pt9): T with Math (079i)Electronics for the Inquisitive Experimenter2025-08-06 | In this video I am going to show you how to design a T impedance matching network using the Equations.
So far in this series, I've had the * Introductory video to impedance matching. * Four videos on designing the L configuration impedance matching configuration. - The first two were type A with a Smith chart and then the math. - The second two were type B with a Smith chart and then the math. * Two videos designing a PI configuration impedance matching network using the Smith Chart and Math. * The video on designing a T configuration impedance matching network using the Smith Chart. ***LINKS TO ALL OF THESE VIDEOS ARE BELOW***
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:40 Define Objectives 02:07 Prepare Impedances 03:27 ID Players THE Math 05:00 The Phase 07:45 X1, Xa, L1 10:01 X2, Xb, C1 11:39 X3, Xc, L2 CHECKING 14:12 Zin 17:10 Zout 20:01 Final Comments and Toodle-OotsHow to Read an Analog Meter Accurately (019a_v2025)Electronics for the Inquisitive Experimenter2025-07-30 | Do you want to get the best accuracy out of your analog meter? Sometimes we just do not need super accuracy when we glance at a meter to take a reading. We just want a ballpark, "Are we OK" kind of idea. There are times, however, where we need to be as accurate in our reading as possible. In this video I will help you understandu three things about reading them that can make a significant difference. What are these three things and how do we accommodate them in reading an analog meter movement? Updated and cleaned up from its original release. ---------------------------- Time Marker Notes 00:05 Introductory Comments 00:21 Are Analog Meters a thing of the past? 01:38 #1: Overcoming Friction 02:34 #2: Overcoming Parallax 04:54 #3: The Right Position 05:41 Final Comments & Toodle-Oots -----------------------------Impedance Matching (Pt8): T with a Smith Chart (079h)Electronics for the Inquisitive Experimenter2025-07-23 | In this video I am going to show you how to design a T impedance matching network using the Smith Chart.
So far in this series, I've had the * Introductory video to impedance matching. * Four videos on designing the L configuration impedance matching configuration. - The first two were type A with a Smith chart and then the math. - The second two were type B with a Smith chart and then the math. * Two videos designing a PI configuration impedance matching network using the Smith Chart and Math.
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:50 The Rules 06:17 Problem Definition 07:05 STEP #1: Impedance Preparation 09:13 STEP #2: Plot Impedances on Smith Chart 11:00 STEP #3: Read the Admittances from the Smith Chart 13:46 STEP #4: Plan Our Route 16:34 STEP #5: Read Impedances & Admittances for Points B & C 19:49 STEP #6: Trip from Point A to Point B 22:07 STEP #7: Trip from Point B to Point C 24:53 STEP #8: Trip from Point C to Point D 26:38 STEP #9: Checking 26:38 a. INPUT Impedance 29:41 b. OUTPUT Impedance 32:25 Final Comments and Toodle-OotsAdding Adjustment to Your Ammeter (019g-v2)Electronics for the Inquisitive Experimenter2025-07-16 | LINK to creating your own meter shunt: youtu.be/lyqUSvlnWow Are you are trying to design a higher current ammeter and the needed shunt resistor is just not available off the shelf? --OR-- Do you want to add some adjustability to your ammeter design?
In either case, in this video I will be showing you how to complete the design of that ammeter and get it just right.
The process is amazingly simple.
LINK: How to Create Your Own Meter Shunt youtu.be/lyqUSvlnWow ---------------------------- Time Markers for your convenience: 00:05 Introduction Design 00:49 Introduction 02:01 Quick Math-Initial Solution 02:23 The Problem 03:11 The Solution 04:51 Another Challenge 05:52 The Solution to the new challenge 06:29 The Complete Solution Testing 07:06 Planning the Test 08:53 Preparation 10:27 Performing the Test 11:20 Final Adjustment 12:11 Concluding Comments & Toodle-OotsImpedance Matching (Pt7): PI with a Math (079g)Electronics for the Inquisitive Experimenter2025-07-09 | In this video I am going to show you how to design a PI impedance matching network using the equations (MATH).
So far in this series, I've had the * Introductory video to impedance matching. * Four videos on designing the L configuration impedance matching configuration. - The first two were type A with a Smith chart and then the math. - The second two were type B with a Smith chart and then the math.
The last video was on designing a PI configuration impedance matching network using the Smith Chart.
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:35 Defining Our Application 02:04 Preparing Our Circuit 05:30 Defining the Players in the Equations 07:14 Determining the Phase Angle 09:43 Calculating X1, Xa and C1 12:38 Calculating X2, Xb and L1 14:38 Calculating X3, Xc and C2 18:21 Checking Our Results 18:27 Calculating the Input Impedance 22:50 Calculating the Output Impedance 27:14 Final Comments and Toodle-Oots!Impedance Matching (Pt6): PI with a Smith Chart (079f)Electronics for the Inquisitive Experimenter2025-06-25 | In this video I am going to show you how to design a PI impedance matching network using the Smith Chart.
So far in this series, I've had the introductory video to impedance matching. This was followed by four videos on designing the L configuration impedance matching configuration. The first two were type A with a Smith chart and then the math. The second two were type B with a Smith chart and then the math.
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:23 Essential Rules 06:01 Problem Definition 07:07 Design It 07:07 STEP#1 - Impedance Preparation 09:16 STEP#2 - Plot Impedances on the Smith Chart 10:58 STEP#3 - Read Admittances off of the Smith Chart 13:45 STEP#4 - Plan Our Route 16:26 STEP#5 - Z and Y of Points B & C 19:46 STEP#6 - Trip from Point A to Point B 22:31 STEP#7 - Trip from Point B to Point C 24:38 STEP#8 - Trip from Point C to Point D 27:01 Check It 27:01 STEP#9a - Checking: Input Impedance 30:37 STEP#9b - Checking: Output Impedance 33:58 Final Comments & Toodle OotsImpedance Matching (Pt5): L-Type B with MATH (079e)Electronics for the Inquisitive Experimenter2025-06-11 | Impedance Matching ... it is all over the place. It is buried in all sorts of electronics. The common thought among many experimenters is that it is beyond their capabilities. Well, I am here to tell you that it need not be!
In this video I am going to show you how to design an L type B impedance matching network using the mathematical equations. What does an L type B configuration look like? As we move in from the input, we first encounter a parallel reactive component and then a series reactive component. We are now at the output. Yep! Just two components! I say "reactive component" because these can be either capacitive or inductive, depending on the route you take.
So far in this series, I've had the introductory video to impedance matching. This was followed by two videos on designing the L-type A impedance matching configuration. The first was designing one with the Smith Chart. The second is designing the same one only using the math.
The Last video was on designing a L-type B using the Smith Chart.
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:41 Defining Objectives 02:06 Step 1: Prepare the Schematic 05:56 Step 2: Identifying the Players 07:16 Step 3: Calculate the Phase Angle 10:09 Step 4: Calculate X1 and C1 12:41 Step 5: Calculate X2 and L1 15:05 Step 6: Checking 15:05 Input Impedance 17:51 Output Impedance 20:10 QUESTIONS: Type A or Type B? 22:06 QUESTIONS: Negative Phase Angle? 22:57 Final Comments and Toodle-OotsImpedance Matching (Pt4): L-Type B with a Smith Chart (079d)Electronics for the Inquisitive Experimenter2025-05-28 | Impedance Matching ... it is all over the place. It is buried in all sorts of electronics. The common thought among many experimenters is that it is beyond their capabilities. Well, I am here to tell you that it need not be!
In this video I am going to show you how to design an L type B impedance matching network using the Smith Chart. What does an L type B configuration look like? As we move in from the input, we first encounter a parallel reactive component and then a series reactive component. We are now at the output. Yep! Just two components! I say "reactive component" because these can be either capacitive or inductive, depending on the route you take.
So far in this series, I've had the introductory video to impedance matching. This was followed by two videos on designing the L-type A impedance matching configuration. The first was designing one with the Smith Chart. The second is designing the same one only using the math.
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments & Howdies! 02:43 The Rules You Need to Know 03:12 Rule #1 03:40 Rule #2 03:55 Rule #3 04:22 Rule #4 04:43 Rule #5 04:55 Rule #6 06:17 Rule #7 06:30 Rule #8 06:54 Our Example 06:54 Intro 07:32 Step #1 - Impedance Preparation 10:00 Step #2 - Plot Impedances on the Smith Chart 11:12 Step #3 - Read Admittance Values 13:25 Step #4 - Plan the Route 16:19 Step #5 - Reading Impedance and Admittance for Point B 17:43 Step #6 - Determine Component #1 20:35 Step #7 - Determine Component #2 22:52 Step #8 - Checking: Input Impedance 24:14 Step #9 - Checking: Output Impedance 25:05 Final Comments and Toodle-OotsImpedance Matching (Pt3): L-Type A with Math (079c)Electronics for the Inquisitive Experimenter2025-05-14 | Impedance Matching ... it is all over the place. It is buried in all sorts of electronics. The common thought among many experimenters is that it is beyond their capabilities. Well, I am here to tell you that it need not be! In this video I am going to show you how to design an L type A impedance matching network using the mathematical equations. What does an L type A configuration look like? As we move in from the input, we first encounter a series reactive component and then a parallel reactive component. We are now at the output. Yep! Just two components! I say "reactive component" because these can be either capacitive or inductive, depending on the route you take.
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:44 Defining Our Objectives 02:11 Circuit Preparation 05:49 Identifying the Players (R1,R2,X1,X2) 07:20 The Math 07:20 The Phase 10:21 Calculate X1, Xa and L1 12:58 Calculate X2, Xb and C1 16:06 Final Checks 16:06 The Input Impedance 18:54 The Output Impedance 21:25 Final Comments, Negative Phase and Toodle-OotsImpedance Matching (Pt2): L-Type A with a Smith Chart (079b)Electronics for the Inquisitive Experimenter2025-04-30 | Impedance Matching ... it is all over the place. It is buried in all sorts of electronics. The common thought among many experimenters is that it is beyond their capabilities. Well, I am here to tell you that it need not be! In this video I am going to show you how to design an L type A impedance matching network the easy way. What does an L type A configuration look like? As we move in from the input, we first encounter a series reactive component and then a parallel reactive component. We are now at the output. Yep! Just two components! I say "reactive component" because these can be either capacitive or inductive, depending on the route you take. I am going to walk through an example using the easiest possible method which uses the Smith Chart. I provided a walk through the important parts of the Smith Chart for you to know in the last video in this series. If you missed that one, here is a link to that video: youtu.be/J_kujlActGo
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:26 The Ground Rules 05:40 Impedance Preparation 08:03 Plotting the Impedances 09:21 Read the Admittances 11:34 Plot Our Course 14:31 Point B: Impedance and Admittance Values 15:54 The Trip: Point A to Point B 17:37 The Trip: Point B to Point C 19:40 Checking the Results: Zin & Zout 21:31 Final Comments and Toodle-OotsImpedance Matching (Pt1): Introductions (079a)Electronics for the Inquisitive Experimenter2025-04-16 | This video is all about introducing you to the world of Impedance Matching.
For most folks who think about this, it can be quite an intimidating subject. "I could never do that!" is the common mantra. It turns out, however, that is isn't as hard as it seems on the surface.
I want to emphasize ... YOU CAN DO THIS!
I want to help you to gain some confidence and the skill to do this.
In this video I will introduce you to the goal of Impedance Matching as well as the two methods you could use to do it.
One of these two methods is the oft avoided Smith Chart (of itself is more intimidating than it needs to be). I will help you tiptoe into the shallows of the aspects of the Smith Chart you need so you can perform Impedance Matching using discrete components like capacitors and inductors.
In the next video I am going to be using the Smith Chart to actually design an Impedance Matching circuit using the principles learned in this video. If you can read a road map and find your way from point A to point B, then YOU CAN DO THIS!
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:56 The Object of Impedance Matching 04:35 Two Methods of Impedance Matching === Introduction to the Smith Chart 06:41 The Impedance Side 10:30 The Admittance Side 13:42 Final Comments and Toodle-OotsThe Mailbox Indicator Project (077)Electronics for the Inquisitive Experimenter2025-04-02 | This video is all about my Mailbox Indicator project. The object is to provide a totally solar powered indicator LED for when the door of the mailbox has been opened. This way we know when and if the mail has arrived.
Why this project? We live out in the country in Iowa. As such, our mailbox is almost 100 feet from our front door. The mail comes at varying times of day depending on various reasons including weather and packages being delivered along the postman's route.
Making trips out to the mailbox to check for mail be a bit unpleasant when the weather is unpleasant like rain, sleet and the like only discover that either we have no mail today or it hasn't arrived yet.
So, we wanted some way to know for sure when the mail has arrive or if we even have a reason to make the trip out to the mailbox.
LINK to the OSH Park project to get the Perfect Purple PCBs Promptly: The Main Control Board oshpark.com/shared_projects/FB5rX8yE The Door Sensor Board oshpark.com/shared_projects/Z1bfR5sv NOTE: I created my own door sensor assembly by hand wiring it using an SOT-23 breakout board. I provide the PCB layout for the Door Sensor board I *would* have used *IF* I chose to have it fabricated for me. It would have cost me $1.15 for three boards if I had.
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 02:16 Project Goals 04:29 The Design 04:29 The Top Level View 05:48 The Specifics 05:52 The Solar Panel 08:07 Power Control 09:48 Power Regulation 10:37 LED Driver & Control 11:16 LED Selection 13:00 LED Memory 14:10 Door Sensor 15:34 Reset 18:32 Installation 19:10 The Solar Panel 20:32 The Main Control Box 21:13 The LED 22:10 The Door Sensor 22:43 The Reset Button 23:00 The Wiring Guard 23:16 Final Comments and Toodle-OotsBONUS: Capacitive Current Limiter (078)Electronics for the Inquisitive Experimenter2025-03-28 | BONUS VIDEO: A curiosity ... use a capacitor as a current limiter for an LED. Yep, you read that right! A friend of mine told me that I just HAD to drop this out here as a video when I told him about it. So...here it is! If you have an A.C. voltage source that you want to use to light up an LED, then you have a choice between current limiting devices. You could use a resistor, which is the traditional way to do this. OR ... you could use a capacitor with the proper capacitive reactance for the frequency of your A.C. source. But there is a caveat to this. You cannot *just* stick it between the A.C. source and the LED. Find out what else you have to do to make this work in this short video.Antenna Tuners: The Math (076e)Electronics for the Inquisitive Experimenter2025-03-19 | In my video on the Feedline Side of the antenna tuner, I refered to a mathematical exercise that I performed using a spreadsheet. I had some requests for a video showing the math that I used. That is what this video is all about.
Do not worry, the math is very simple and easily done on your scientific calculator. I will step you through it all, one step at a time.
In this video, I will present three methods for determining the total loss of power delivered to the antenna given that you know the SWR at the antenna and the loss of the feedline (Matched Loss).
If all you know is the SWR as measured at the tuner end of the feedline, I will show you how to calculate the SWR at the antenna. I will also show you how to calculate the power actually being delivered to the antenna.
The first method uses the chart or graph presented in the American Radio Relay League's Antenna Book or in Walter Maxwell's book, "Relfections." This is the "Graphical Method."
The second method uses the math from my 1984 copy of the A.R.R.L. Antenna Book.
The third method is the Spreadsheet Method. It is the method that I used in my video on the feedline side of the tuner. It will give us an inside view of the entire process and help us to see the equilibrium being achieved. You put in the SWR at the antenna, the power provided from the transmitter and the native loss of the feedline (matched loss). It, then, does the rest for you.
I reference the following very helpful book: "Reflections III: Transmission Lines and Antennas" By: M. Walter Maxwell, W2DU Published by: CQ Communications (c) 2010
======= VIDEO LINKS ========== Antenna Tuners: Impedance and SWR (076a) youtu.be/dMVx2uhGZfs Antenna Tuners: The Feedline Side = The Source and Destination of Reflected Power (076b) youtu.be/yuxuQdoL1GM Reflected Power: Lost then Found (076c) youtu.be/Vr0Z0KUoiOU ======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:35 What You Need to Know 04:51 Method #1: The Graphical Method 08:28 Method #2: The Mathematical Method 11:01 Method #3: The Spreadsheet Method 14:53 Final Comments and Toodle-OotsAntenna Tuners: How does it do THAT? (076d)Electronics for the Inquisitive Experimenter2025-03-05 | Antenna Tuners or Antenna Matching Networks ... in the last videos I showed how the antenna tuner re-reflects the reflected power from the antenna BACK at the antenna. But I only said that it was because of the conjugate matching going on. I did NOT tell you how this conjugate matching actually does it.
In this video, I will try to explain how this all happens. I will perform three experiments which should help to visualize the process.
I reference the following very helpful book: "Reflections III: Transmission Lines and Antennas" By: M. Walter Maxwell, W2DU Published by: CQ Communications (c) 2010
======= VIDEO LINKS ========== Antenna Tuners: Impedance and SWR (076a) youtu.be/dMVx2uhGZfs Antenna Tuners: The Feedline Side = The Source and Destination of Reflected Power (076b) youtu.be/yuxuQdoL1GM Reflected Power: Lost then Found (076c) youtu.be/Vr0Z0KUoiOU ======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments The Basis 01:03 Conjugate Matching 03:02 Resonance The Experiments 05:32 Experiment #1: The LC Resonant Circuit 06:47 Experiment #2: The LC Resonant Circuit with 10 Ohm resistors 09:04 Experiment #3: The LC Resonant Circuit with Resistors and Feedline 10:23 What does this all mean? 11:58 Final Comments and Toodle-OotsReflected Power: Lost then Found (076c)Electronics for the Inquisitive Experimenter2025-02-19 | This video is all about my own change in mindset regarding the destination of power reflected from the antenna when an antenna tuner is used and it is properly adjusted. I give credit to what I have read in the American Radio Relay League's book "Reflections: Transmission Lines and Antennas" authored by M. Walter Maxwell. I am thankful for the subscriber/viewer for pointing me to this book.Antenna Tuners: The Feedline Side = The Source & Destination of Reflected Power (076b)Electronics for the Inquisitive Experimenter2025-02-19 | Antenna Tuners or Antenna Matching Networks ... they are ubiquitous in the Amateur Radio World. They used to be things that hams either built for themselves or bought as a separate unit to include in the shack. Now they are very often included in transceivers. This video is an followup to the previous video on the Impedance and Feedline SWR effects as they apply to antenna tuners.
This video answers the questions: 1. Where does the reflected power come from? 2. Where does the reflected power end up?
There is some amazing and almost magical stuff going on in there!
I reference the following very helpful book: "Reflections III: Transmission Lines and Antennas" By: M. Walter Maxwell, W2DU Published by: CQ Communications (c) 2010
======= VIDEO LINKS ========== Previous Video (076a): youtu.be/dMVx2uhGZfs How to tune an Antenna Tuner with an Antenna Analyzer or nanoVNA (007d): youtu.be/4GaRDRhfBbw ======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:02 Source of Reflected Power: TDR Demonstration 01:02 TDR Introduction 02:27 TDR Experiment 06:32 Reflected Power: Where does it go? 06:33 The Experiment: Setup 10:47 The Results 12:18 The Explanation: The Basis 14:44 The Trips and Cable Loss 18:02 Final Comments and Toodle-OotsAntenna Tuners: Impedance and Feedline SWR - Two Experiments (076a)Electronics for the Inquisitive Experimenter2025-02-05 | ********* NOTE: I make some comments herein about where the reflected power ends up. These are going to be refactored in the next video where I address the issue more directly. ********* Antenna Tuners or Antenna Matching Networks ... they are ubiquitous in the Amateur Radio World. They used to be things that hams either built for themselves or bought as a separate unit to include in the shack. Now they are very often included in transceivers. This video is an adjunct to the previous two videos that I created on the subject of antenna tuners. In this video I will perform two experiments to demonstrate two aspects of what they do. These are related to specific aspects of what they do after they are fully tuned to provide the lowest SWR for the transmitter: 1. Impedance at the Antenna connection 2. Feedline SWR.
The next video will address the topic of the reflected power in the feedline and its associated SWR.
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:35 Experiment #1-Impedance 01:35 Introduction and Setup 02:16 Performing the Experiment 05:11 Experiment #2: Feedline SWR 05:11 Introduction and Setup 05:57 Performing the Experiment 09:06 Final Comments and Tootle-OotsEvaluating Clip-On Ferrite Beads with your nanoVNA (075)Electronics for the Inquisitive Experimenter2025-01-22 | We all have them somewhere ... that clip-on ferrite bead that we bought, was given, scavenged or found. We know absolutely nothing about it. What is it good for? How do I measure it? It's purpose is to increase the inductive reactance of any conductor it is clipped on to. This, then, makes the conductor act like a higher impedance to R.F. and the like to prevent noise or interference from traveling down the wire. But not all ferrite beads and materials are created equal. Not all will do what you might want to do. Which one of those junk box ferrites is the best for your needs? In this video I will show you a very *basic* method of evaluating the performance of a ferrite bead using a nanoVNA. While the totally *ideal* method keeps the wire in the fixture as short as possible, this is a way to compare these clip-ons which can be quite large in size.
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:16 Setup 01:18 The Fixture 02:14 The nanoVNA 04:12 The Measurement 06:50 The Comparison 08:58 Final Comments and Tootle-OotsPutting up a Tower the Right Way (074b)Electronics for the Inquisitive Experimenter2025-01-08 | In the past few years I have been actively involved primarily in bringing down towers of amateur radio operators who have passed away or have had to move. With that said, I've also helped put up towers. In both of these capacities, I've seen a lot of tower installations. I've looked at them with my own two eyes and I've seen people's videos showing their tower installations. I will say that there is a lot of innovation in these installations. So, I thought it would be a good thing to put together a video to help folks who are thinking about putting up their own tower.
What you will find in this video is the method that the manufacturer recommends for installing your tower using a Rohn 25G tower as our example.
The first principle is that the tower was designed around particular installation criterion. If you expect that tower to live up to its design, then the key is installing it according to the manufacturer's and designer's criterion.
Many, many shortcuts have been taken in many installations and folks have gotten away with them. In the distant past, I made some of these same shortcuts out of ignorance. My bad.
This is not a comprehensive "everything there is to know" kind of video. Each tower manufacturer and each model of tower is different than every other and I cannot cover them all in one video. But basic principles apply to all.
======= LINKS ======== LINK to Rohn Full catalog http://www.rohnnet.com/files/2015_Rohn_Full_Catalog.pdf#page=26 LINK to APP ZIP file drive.google.com/file/d/1v895Kq7TxDAWdJKmelGTlU7qncfTGBpu/view?usp=sharing LINK to Excel spreadsheet ZIP file drive.google.com/file/d/1vjgIpOu9ZjXCUwG2CTDjhLjXlRyVV71D/view?usp=sharing ======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 02:10 Wind Load Capacity 02:49 Tower Specifications 03:49 Used Tower Sections??? 04:35 The Two Broad Kinds of Towers 05:50 Planning: What are you going to put up? 06:19 Planning the Tower Itself 08:42 Rotator Selection & Derating 10:18 Selecting an Antenna 10:19 What is the maximum Wind Load I am allowed? 11:48 Apply the safety factor 12:15 Antenna Shopping 13:19 Planning the How of Installation 13:44 The Tower Foundation/Pier 15:11 Guy Anchors 17:42 Guy Wire Planning 21:33 The Checklist ... 26:23 Tower Raising 26:24 The Single Most Important Factor 27:42 The Process 30:49 Setting Guy Wire Tension 33:30 Final Comments and Toodle-Oots30 Foot / 9 meter Antenna Mast on the Cheap (074a)Electronics for the Inquisitive Experimenter2024-12-25 | In this video I will walk though how to build a 30 ft / 9 m antenna support for yourself using simple lumberyard lumber and hardware. I will also show you the modifications I made for my own version that I used at Moose Lake.
Not everyone has a place to support one or both ends of a wire antenna. This problem is not foreign to the amateur radio operator. Back in the long past, they devised a way of creating their own 30 foot or 9 meter support using basic stuff from the lumberyard. It was 40 foot (12 meter) back then when they could get 22 foot lumber! I found this design in a 1940 American Radio Relay League (A.R.R.L.) "The Radio Amateur's Handbook." It is what I used as a starting place to create the antenna mast I used in Moose Lake, Manitoba, Canada when I lived there back in the 1990s. I made some modifications for my own application and it worked great.
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:24 The Design: Its Origins 03:10 The Original Design 04:05 Step#1: Lay out the lumber 04:14 Step#2: Bolt then together 05:03 Step#3: Splay out the legs 05:12 Step#4: Secure the legs in place at the bottom 05:51 Step#5: Add three more cross braces 06:16 Installation 06:22 The Guy Wires 07:22 Locations 07:27 Set#1: Midpoint 07:35 Set#2: Top 07:57 Lengths 09:00 The Pulley & Rope/Cord 09:59 Establish a level foundation 10:19 Base stakes for installation 10:33 Guy Wire Anchors 11:03 Putting the Mast up and into place 11:24 Final mast leveling 11:57 Modifications at Moose Lake, Manitoba, Canada 13:10 Final comments and tootle-ootsStep Attenuator: The Math (073b)Electronics for the Inquisitive Experimenter2024-12-11 | In this video I will walk through the derivation of the equations that I used to design the step Attenuator that I presented in the last video.
I show the major steps in this video. I will not work through the simplification process from one step to the next. The process of simplification is show in the formula sheet on the last page ... the photograph of the white board.
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:49 The Circuit 02:53 The Rin Equation 04:53 The Av Equation (Voltage Gain) 07:30 The Miscreant Term 09:43 The Rp Equation 10:21 The Rs Equation 11:24 Final Comments and Toodle-OotsStep Attenuator Design, Build and Test (073a)Electronics for the Inquisitive Experimenter2024-11-27 | ***CORRECTION*** That is 2^8 * 3 = 768 tests **NOT** (8!+1) * 3 = 120,963 tests. Either way, still too many tests to perform. ***POWER RATING*** Do not apply any more than 250 mW to this attenuator (A.C. or D.C.). That means no more than 3.5 VDC or 250 mW R.F. or any combination of A.C. and D.C. that amounts to 250 mW. ----------------------------------------------------------- In this video I will walk through the * Design * Build * Testing of an eight position Step Attenuator.
I will compare its performance to it predecessor, another eight bank Step Attenuator made a LONG time ago with leaded resistors.
You will find a LINK to the ZIP file below which contains: * The Formulas and Values Sheet which also includes a DigiKey shopping list * All of the needed design files * All of the test results for both the Old and New versions
You will also find LINKS to the OSH Park Projects for both the Single Bank prototype and the Eight bank complete Step Attenuator.
NOTE: I am still experimenting with this new mic and it sounds like I have some over-driving on the audio. I'm still trying to track down the source.
OSH Project for the PCBs 10 dB - single oshpark.com/shared_projects/CzFyVuXd Eight Bank oshpark.com/shared_projects/d4h2Dti2Creepage and Clearance (072)Electronics for the Inquisitive Experimenter2024-11-13 | This video is all about Creepage and Clearance, otherwise known at "Conductor Spacing," for electronic and electrical circuits which have higher operating voltages. We do not want arcs or conductive paths developed between conductors. To prevent this from happening, we need to have enough distance between conductors having voltage differences.
NOTE: Yes, I know I have some overdriving on the audio in the introduction. New mic and didn't get the levels quite right quite yet. You will notice, it is fixed in the subsequent video clips.
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:46 The Overall Picture of Creepage and Clearance 03:38 Creepage 07:46 Clearance 09:04 The Standards 10:55 Final Comments and Toodle-OotsGalvanic Corrosion (071)Electronics for the Inquisitive Experimenter2024-10-30 | Galvanic Corrosion is a problem that affects electronics, mechanics and a LOT more.
In this video I will describe * What Galvanic Corrosion is * What you might see in troubleshooting because of it * How to prevent it. Get this right and you will save yourself a LOT of headaches.
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:20 Two Examples of the Effects 01:20 An Electronic Product 02:34 House Wiring 03:23 The What & Why of Galvanic Corrosion 04:19 How does it act? ...What to look for in troubleshooting 05:35 How do I predict what two metals I can put together 07:04 An example of how to read this chart 09:12 How do I prevent problems? 10:24 Final comments and toodle-ootsMeasuring the Input Impedance of a Product, Circuit or System (070b)Electronics for the Inquisitive Experimenter2024-10-16 | There are two kinds of situations where you might want to measure the input impedance of a product, system or circuit: 1. At a Low frequency like an audio amplifier where there is no real concern about the complex aspects of impedance. 2. At Higher frequencies like a receiver pre-amp where we are very much interested in the complex impedance.
I covered the first of these in the last video. If you missed that one, here is the LINK to it: youtu.be/JCcHrXeIaYQ
In THIS video I will be measuring the input impedance of a VHF preamp that is part of my little 2 meter amplifier. I will see if we can do this with the nanoVNA.
Regardless of what VNA I use to make the measurement, the principles remain the same as to how to go about it. These principles can be applied to other amplifier where the nanoVNA can be used, so stay tuned regardless.
There are some rather surprising results to our efforts.
One of these is the actual SWR which is represented by the measured input impedance at 144 MHz. I kept puzzling at this. I verified it by at least two on-line calculators (Impedance-to-SWR calculators), by my Excel spreadsheet that I developed and by my manual calculation. They all came up with the same numbers!
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:08 Planning Our Measurement 01:13 Concern #1: Input Requirements 03:41 Can the nanoVNA do this? 03:50 nanoVNA Setup 04:41 nanoVNA Results 06:30 Can the Tektronix VNA do this? 06:59 Tektronix VNA Performance 07:29 Concern #2: Output Loading 08:00 SETUP 08:00 Connections 09:37 Tektronix VNA Setup 09:39 Settings 10:33 Calibration (VERY QUICKLY!) 11:16 Adding the Port Extension 12:30 Making the Measurement 12:33 Getting the Amplifier ready 13:05 Measurement Results 14:35 Conclusions and Debriefing 15:25 Toodle-OotsMeasuring the Input Impedance of a Product, Circuit or System (070a)Electronics for the Inquisitive Experimenter2024-10-02 | There are two kinds of situations where you might want to measure the input impedance of a product, system or circuit: 1. At a Low frequency like an audio amplifier where there is no real concern about the complex aspects of impedance. 2. At Higher frequencies like a receiver pre-amp where we are very much interested in the complex impedance.
In this video I will be addressing the first of the two. I will be measuring the input impedance of a small, inexpensive audio amplifier. I will discover how this input impedance is affected by: * The position of the volume control * The level of the input signal * The frequency of the stimulus
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 00:59 Why not use a DVM to measure Input Z? 01:53 Planning our Measurements 02:52 What is "Line Level?" 03:22 What is the difference between dBv and dBu? 04:20 Planning our Test Voltage 06:12 Three Important Questions ... 06:15 1. How does the Volume Control affect the Input Impedance? 06:43 2. How does the Signal Level affect the Input Impedance? 06:59 3. How does Frequency affect the Input Impedance? 07:36 Setting Up for the Test 07:39 Test Equipment Settings 09:00 Test Equipment Connections 10:00 First Test: How does the volume control affect the Input Impedance? 12:40 Second Test: How does the signal level affect the Input Impedance? 14:20 Third Test: How does Frequency affect the Input Impedance? 15:21 Bringing it all together 15:56 Parting comments and Toodle-OotsSingle Sideband: Where do those extra harmonics come from? (036b)Electronics for the Inquisitive Experimenter2024-09-18 | This video is in direct response to a questions about where the extra harmonics came from as seen in the original video on Single Sideband. Se the link, below, to the original video.
I will show what the ideal Amplitude Modulated signal **SHOULD** look like. I will then explain why the spectrum we saw in the original video did NOT look like this.
=== LINKS for You === LINK to the Single Sideband Video (036a): youtu.be/AHRtOkR1hEA
---------------------------------- Time Markers for Your Convenience ---------------------------------- 00:05 Introductory Comments 01:02 What does a perfect spectrum look like for an AM signal? 04:40 What went wrong? 05:59 What do nonlinearities do? 07:59 Final Comments and Toodle-OotsImpedance, Reflection Coefficient, Return Loss and VSWR (SWR) (069)Electronics for the Inquisitive Experimenter2024-09-04 | This video is in direct response to a request to create a video which talks about the relationship between Impedance and SWR.
I will define and discuss both Impedance and VSWR (also known as SWR). However, in order to get a complete picture of the whole, I need to include their cousins, Reflection Coefficient and Return Loss.
I will build from the foundation of an understanding of Impedance through the next layer up of Reflection Coefficient, through Return Loss, to the final understanding of VSWR.
Why do I deal with SWR last? In my mind "all roads lead to VSWR." In other words, all of these other entities can be used to calculate VSWR, so it makes sense to understand them first.
With that said, because they are all mathematically interrelated, any one of these can be calculated if we know any one of the others with one distinct exception ... the complex expression of both Reflection Coefficient and Impedance. We CAN calculate the *magnitude* of the Reflection Coefficient.
=== LINKS for You === LINK to the Impedance Basics video (055): youtu.be/48RNn5tXw2g
LINK to the Math for Reactive Circuits: Using EXCEL's Muscle video (00i2): youtu.be/vF6pWy6QAbs
LINK to the Math for Reactive Circuits: Using Pencil and Paper (00i1): youtu.be/LSNx5a8z29I
---------------------------------- Time Markers for Your Convenience ---------------------------------- 00:05 Introductory Comments 01:08 Impedance 05:33 Reflection Coefficient 09:36 Return Loss 12:20 VSWR aka SWR 16:48 Final Comments and Toodle-Oots =============================CASCODE Amplifier (Pt 3): Designing in a Fixed Gain (066g3)Electronics for the Inquisitive Experimenter2024-08-21 | BJT Circuit Analysis: The CASCODE Amplifier (Pt 3) - Designed in Gain (066g3) =========================================================================================== This is the third video in this series on the CASCODE Amplifier. In the first video, I explained the WHY behind the CASCODE configuration and the HOW it works behind its operation. Here is a LINK to that video if you missed it: youtu.be/j3r0-3vYkO4
In the last video, I showed you how to design one. Here is a LINK to that video if you missed that one: youtu.be/UrQD4-8d5VU
In this video I will be showing you how to design in a specific gain to the amplifier. I will show you three ways to accomplish this. I will also show how the gain limited versions improve the upper end bandwidth of the amplifier.
As a kind of extra credit portion, I am going to show the effects of the source impedance on the performance of the amplifier.
---------------------------------- Time Markers for Your Convenience ---------------------------------- 00:05 Introductions 02:12 A Few Simple Definitions 04:20 WAY #1: Set Rc 06:58 WAY #2: Feedback 09:17 WAY #3: Split Emitter Resistor 13:22 The Effects of Source Impedance 15:41 Parting Comments and Toodle-OotsBJT Circuit Analysis: The CASCODE Amplifier (Pt 2) - DESIGN (066g2)Electronics for the Inquisitive Experimenter2024-07-31 | In the last video, I explained the WHY behind the CASCODE configuration and the HOW it works behind its operation. Here is a LINK to that video if you missed it: youtu.be/j3r0-3vYkO4
In this video I will be showing you how to design one. I will walk through the entire design process including all of the assumptions, rules of thumb and engineering estimates needed to make this work.
I will also demonstrate the benefits of this configuration both in the simulation world and with a bench experiment.
---------------------------------- Time Markers for Your Convenience ---------------------------------- 00:05 Introductory Comments 01:18 Establish Design Goals 03:00 Calculating Transistor Currents 05:31 Calculate Re 06:46 Calculate Q2's Base Voltage 07:55 Calculate R1, R2 (Rb3), Rth, Vth (Thevenin Stuff) 07:55 Introduction to the Thevenin Stuff (a reminder) 08:45 Calculate Rth 09:31 Calculate V(Rth) 10:21 Calculate Vth 11:36 Calculating R1 & R2 11:43 Calculate R1 12:20 Calculate R2 13:14 Calculating the Currents in the Bias Resistor Chain 13:21 Calculating I(Rb3) 14:12 Calculating I(Rb2) 15:41 Calculating I(Rb1) 17:21 Unstucking the Stuck with Engineering Knowledge (V(Rb2)) 19:16 Calculating the Rest of the Bias String (Rb2 & Rb1) 19:16 Calculating Rb2 19:58 Calculating V(Rb1) so we can find Rb1 21:16 The Value of Rb1 by Ohm's Law 22:03 The Conundrum ... Solved 24:05 Calculating Vcq so we can find Rc 26:44 Calculating V(Rc) 27:11 Calculating Rc 28:19 Calculating the Anticipated Gain 30:32 Performance Evaluation 30:33 Using LTSpice Simulation 33:18 The Bench - Breadboard Results 35:17 Final Comments and Toodle-OotsWhat is Early Voltage? (066f)Electronics for the Inquisitive Experimenter2024-06-26 | Maybe you have heard of this whole Early Voltage business and maybe you haven't. It has all to do with the bipolar junction transistor and invades certain aspects of circuit analysis. In this video I will tell you all about the Early Effect and how it relates to the Early Voltage. I will also tell you how it relates to circuit analysis. To answer the request for a means of calculating the value of the Early Voltage, I provide this as well.
---------------------------------- Time Markers for Your Convenience ---------------------------------- 00:05 Introductory Comments 01:07 The "Early Effect" 04:14 The "Early Voltage" Defined 04:40 The Classic Explanation & Example 06:52 A Real World Example: Randomly Chosen 2N3904 08:26 Why use Va = 100 Volts? 09:20 Why do I even *care* about the Early Voltage? 09:26 Where is it used? 10:32 Why don't we see it being used? 12:17 Calculating Va 13:57 Final Comments and Toodle-OotsnanoVNA: Measuring the Frequency Response of an Amplifier Filter (068e)Electronics for the Inquisitive Experimenter2024-06-12 | In this video I will be showing you how to use your nanoVNA in stand alone mode to measure the frequency response of a VHF receive preamplifier that exists in my amplifier add on.
Included in this video are * Set up the nanoVNA for a frequency response (through) measurement on an active device * Proper VNA calibration * Make the measurement results more readable by changing the REFERENCE POSITION and SCALE.
====================== ==== VIDEO LINKS ===== ====================== VIDEO: VNA Foundations (first video in the series) youtu.be/8IhJMGxU5xA == THIS SERIES == VIDEO#1: nanoVNA: A Practical Menu Walk Through youtu.be/_96N3oGFatE VIDEO#2: nanoVNA: Measuring the SWR of an Antenna youtu.be/8s420GKsynM VIDEO#3: nanoVNA: Measuring the Input Impedance of a Filter youtu.be/JFxZsYmFe8I VIDEO#4: nanoVNA: Measuring the Frequency Response of a Filter youtu.be/S8MCcY6dHZ4
=======================================
---------------------------------- Time Markers for Your Convenience ---------------------------------- 00:05 Introductory Comments 01:01 The Planning Phase 01:05 The Electrical Questions 02:17 1. D.C. Levels 03:10 2. The Amplifier's Maximum Input Level 05:14 3. The Amplifier's Anticipated Gain 06:05 4. The nanoVNA's Maximum Input for Channel 1 06:51 5. The nanoVNA's Stimulus Level from Channel 0 08:44 Bringing it together 09:27 Connectors & Adapters 09:58 The Connections for our Measurement 11:31 Measurement Methodology 11:37 WAY#1 13:35 WAY#2 15:13 Setting up the nanoVNA for the Measurement 17:04 nanoVNA Calibration 19:18 Making the Measurement 19:19 Final Preparations 19:24 Power Up! 19:45 Final Connections 20:43 Making the Measurement 20:56 Moving the Reference Position 22:09 Changing the Scale 22:41 The Measurement Results 23:55 Final Comments and Toodle-ootsnanoVNA: Measuring the Frequency Response of a Filter (068d)Electronics for the Inquisitive Experimenter2024-05-29 | In this video I will be showing you how to use your nanoVNA in stand alone mode to measure the frequency response of what was **supposed to be** a 50 MHz bandpass filter that I threw together. This filter was supposed to have a 50 MHz pass frequency.
I discovered that one (or more) of the unmarked components were not the value I expected them to be, so the reality of this filter is somewhat different than planned. How different? You have to watch the video to find out.
Included in this video are * Set up the nanoVNA for a frequency response (through) measurement * Proper VNA calibration * Make the measurement results more readable by changing the SCALE.
See below for the time markers ...
========================== Filter Autopsy Results ... ========================== First, this was a true "throw-together" filter, built without regard to various topologies and the like. So, its response will not adhere to any given standard response. Yes, the component values were different than expected. I measured the components in place (I know, not recommended for best accuracy). This included a wire jumper (AKA: inductor) which was part of the implementation. After putting the measured and adjusted values into the LTSpice model the estimated theoretical frequency response was f1 = 27.19 MHz, f0 = 45.037 MHz, f2 = 78.29 MHz The measured frequency response was f1 = 27.1 MHz, f0 = 45.1 MHz, f2 = 76.6 MHz I still do not quite get what is happening on the upper side. 1.69 MHz dif??? Nonetheless, for a thrown together filter, it is ... 'OK.'
====================== ==== VIDEO LINKS ===== ====================== VIDEO: VNA Foundations (first video in the series) youtu.be/8IhJMGxU5xA == THIS SERIES == VIDEO#1: nanoVNA: A Practical Menu Walk Through youtu.be/_96N3oGFatE VIDEO#2: nanoVNA: Measuring the SWR of an Antenna youtu.be/8s420GKsynM VIDEO#3: nanoVNA: Measuring the Input Impedance of a Filter youtu.be/JFxZsYmFe8I ======================================= ---------------------------------- Time Markers for Your Convenience ---------------------------------- 00:05 Introductory Comments 02:00 Step 1: Planning 02:05 The Electrical Side 04:10 The Mechanical Side 05:13 Step 2: Measurement Preparations 05:16 Setting up the nanoVNA 05:22 The Frequency Settings 06:09 The Display Setup 06:20 TRACE setup 06:50 Setup TRACE 0 07:00 CHANNEL setup 07:28 FORMAT setup 07:56 MARKER Setup 08:11 Select the Markers 08:34 Connecting Things Up 09:01 Calibration 10:21 Final Preparation: Connect to the UUT 10:32 Step 3: The Measurement 10:32 Changing the SCALE 11:22 Marker Movement for Measurement 11:55 Finding the Pass Frequency, f0 12:07 MARKER SEARCH function 12:12 Select the Marker 12:37 Invoke the SEARCH function 12:56 Measurement Results 12:57 The Pass Frequency, f0 13:19 Low End Response: MARKER 1 13:39 High End Response: MARKER 3 13:59 Comparing Results with Theory 14:59 Final Comments and Toodle-OotsnanoVNA: Measuring the Input Impedance of a Filter (068c)Electronics for the Inquisitive Experimenter2024-05-15 | In this video I will be showing you how to use your nanoVNA in stand alone mode to measure the input impedance of a 50 MHz bandpass filter that I threw together. This filter is supposed to have a 50 Ohm input impedance. Let's see what it really is!
Included in this video are * Set up the nanoVNA for a impedance measurement * Proper VNA calibration * Add a Port Extension or ELECTRICAL DELAY after calibration * Make the measurement results more readable by changing the SCALE. ====================== === PROMISED LINKS === ====================== nanoVNA -Official- Site (so they claim) nanorfe.com/nanovna-v2.html nanoVNA Manual (with menu map) nanorfe.com/nanovna-v2-user-manual.html Purchase nanoVNA V2 Plus 4 at tindie.com/stores/hcxqsgroup
====================== ==== VIDEO LINKS ===== ====================== VIDEO: VNA Foundations (first video in the series) youtu.be/8IhJMGxU5xA == THIS SERIES == VIDEO#1: nanoVNA: A Practical Menu Walk Through youtu.be/_96N3oGFatE VIDEO#2: nanoVNA: Measuring the SWR of an Antenna youtu.be/8s420GKsynM ======================================= ---------------------------------- Time Markers for Your Convenience ---------------------------------- 00:05 Introductory Comments 01:29 Planning the Project 01:34 The Electrical Side 02:47 The Mechanical Side 04:36 Setting Stuff Up for the Measurement 04:38 The nanoVNA 04:45 The Frequency Setup 05:30 Setup the Display 05:44 Trace Selection 06:18 Trace Configuration 06:21 Trace 0 06:33 Channel Selection 06:49 Format 07:06 Data Format 07:51 Trace 1 08:08 Channel Selection 08:23 Format 08:49 Bench Connections - Preparing for Calibration 09:05 Calibration 09:25 OPEN 09:37 SHORT 09:47 LOAD 10:10 Saving Calibration and Configuration Data 10:20 Preparations for Measurement 10:23 Installing the SMA-to-N Adapter 10:33 The Port Extension (AKA: Electrical Delay) 10:46 Setup Markers 11:26 Apply the Port Extension 13:08 Get rid of the second trace (TRACE 1) 13:32 Making the Actual Measurement 13:38 Connecting things up 13:43 Terminate the Filter's Output in 50 Ohms 14:01 Connect the Measurement-Ready nanoVNA 14:16 Observe the Screen - too small! 14:22 Changing the Scale 15:22 The Measurement Results 16:18 Final Comments and Toodle-OotsnanoVNA: Measuring the SWR of an Antenna (068b)Electronics for the Inquisitive Experimenter2024-05-01 | In this video I will walk through the process of setting up your nanoVNA to measure the SWR of an existing antenna intended for use in the 7.0 to 7.3 MHz band. ************************* ****** CAUTION ******** ************************* Antennas build up STATIC! **ALWAYS** SHORT AND GROUND your antenna to discharge static before connecting it to your nanoVNA or antenna analyzer. Failure to do so may result in the ruin of the nanoVNA or antenna analyzer. ************************* I step through this process one step at a time so you can follow along to make your own measurement on your own antenna. ** Yes I am aware that the mic gain was up a little too high and I got some flat topping. It is a work in progress. ** ====================== === PROMISED LINKS === ====================== nanoVNA -Official- Site (so they claim) nanorfe.com/nanovna-v2.html nanoVNA Manual (with menu map) nanorfe.com/nanovna-v2-user-manual.html Purchase nanoVNA V2 Plus 4 at tindie.com/stores/hcxqsgroup
====================== ==== VIDEO LINKS ===== ====================== VIDEO: VNA Foundations (first video in the series) youtu.be/8IhJMGxU5xA == THIS SERIES == VIDEO#1: nanoVNA: A Practical Menu Walk Through youtu.be/_96N3oGFatE =======================================
---------------------------------- Time Markers for Your Convenience ---------------------------------- 00:05 Introductory Comments 01:24 Setting Up the Frequency Limits 02:41 Setting Up the Display 02:47 Turning On/Off Traces 03:45 Choosing Your Channel 04:08 Selecting the Measurement Type/Format 04:41 Preparing for Your Measurement 04:45 The Physical Side of Preparation: Cables and Adapters 07:51 Calibration 08:21 OPEN 08:36 SHORT 08:54 LOAD 09:25 Saving Calibration & Setup Data 10:20 Making the Measurement 10:46 Set Up Your Marker 11:30 Using the Marker 12:13 The Measurement Results 12:53 Final Comments and Toodle-OotsnanoVNA: A Practical Menu Walk Through (068a)Electronics for the Inquisitive Experimenter2024-04-17 | So you have just got a nanoVNA and it's a bit confusing. I don't blame you! In this video I will walk through the menu of the nanoVNA with an eye to what it takes to get it set up to make a measurement of some sort. I will explain all of those FORMAT options like: LINEAR, REAL, IMAG, DELAY, POLAR, RESISTANCE, REACTANCE, SMITH and so on. Some of these are a bit mysterious to those who are new to the whole VNA world.
My intent is that this will have some real practical implications for you.
====================== ==== VIDEO LINKS ===== ====================== VIDEO: VNA Foundations (first video in the series) youtu.be/8IhJMGxU5xA VIDEO: Q-Factor youtu.be/M6Ip1qkc8EM VIDEO: Measuring Inductance, Capacitance and Impedance with the nanoVNA youtu.be/Pti8Erw_Kkg VIDEO: Measuring stuff outside the 50-Ohm World of the nanoVNA youtu.be/dgDS4rjb-GU =======================================
---------------------------------- Time Markers for Your Convenience ---------------------------------- 00:05 Introductions 01:43 The Main Menu-An Overview 03:54 Getting Ready to Measure: Planning! 05:01 Setting up the nanoVNA 05:18 Configuring what I see on the screen. 05:35 The TRACE Option 07:26 Trace Format 08:22 Channel Selection 09:21 Reflection Coefficient: A little Background 11:36 Display Formats 11:37 LOG MAG 12:51 Phase 13:18 Delay 15:06 Smith 18:05 SWR 18:37 POLAR 20:29 LINEAR 21:16 REAL 21:49 IMAG 22:25 RESISTANCE 22:45 REACTANCE 23:07 Q FACTOR 24:46 Next Steps: Configure other Traces 25:08 Defining Test Frequencies 25:18 Start & Stop Frequencies 27:26 Center Frequency & Span 28:33 Setting up Markers 28:34 What is a marker? 29:09 Marker Setup 29:17 Select Markers 30:02 Marker formatting 30:38 Marker Use 32:09 Calibration 34:49 Parting comments and Toodle-ootsLoad Line Analysis: Answers to Two Poignant Questions (066e4)Electronics for the Inquisitive Experimenter2024-04-03 | And now, in this video, I am going to answer two poignant questions: QUESTION #1: So, what is all of this stuff good for? Why should I bother with it? QUESTION #2: The D.C. Load Line and the A.C. Load Line aren't that much different. In fact, the A.C. Load Line indicated a lower gain. Yet, the overall gain of the circuit is WAY higher. How is *that* possible?
I've provided links to all of the videos in this series below the time markers. ======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 02:02 Why even bother with all of this? 03:48 Why is the gain so different when the load lines aren't? 10:25 Final Comments and Toodle-Oots
==== This Video Series Links ==== Video#1: Load Line Analysis: Foundations youtu.be/-fQotNX3gT0 Video#2: Load Line Analysis: Example #1 - A Simple Common-Emitter Circuit youtu.be/dOv_nsBvYTM Video#3: Load Line Analysis: Example #2 - A Beta Stabilized Common-Emitter Circuit youtu.be/1omZ28NtiI0 Video#4: Load Line Analysis: Answers to Two Poignant Questions youtu.be/ajZB4GRzkOcLoad Line Analysis: Example #2 - A Beta Stabilized Common-Emitter Circuit (066e3)Electronics for the Inquisitive Experimenter2024-04-03 | In the last video I created the D.C. and A.C. Load Lines for a simple Common-Emitter circuit.
In this video I am going to create the D.C. and A.C. Load Lines for a beta-stabilized, Common-Emitter circuit which has a split Emitter resistor.
I've provided links to all of the videos in this series below the time markers.
=============== LINKS ================= LINK to the promised formula sheet: drive.google.com/file/d/1eXVT3gjQxbqzl_kY6Zyo3nHhxxNkUHbe/view?usp=drive_link ======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:29 The Circuit: A Tour 02:35 The Family of Curves for this Example 02:49 The D.C. Load Line 02:50 Kirchhoff's Voltage Equation around the Collector-Emitter Loop 06:00 Plotting the D.C. Load Line - Three Points 06:13 Question #1: Vce=? when Ic=0 06:44 Question #2: Ic=? when Vce = 0? 07:21 Drawing the Line 07:31 Plot the Quiescent Operating Point 08:13 The A.C. Load Line 08:17 Schematic Preparation 08:52 Step #1: Short D.C. Sources 09:06 Step #2: Short all Capacitors 10:17 Step #4: Write KVL around the Collector Loop 14:41 Plotting the Load Line Points 14:46 Question #1: Vce=? when Ic=0? 15:27 Question #2: Ic=? when Vce = 0? 16:12 Draw the Line 16:23 An Observation regarding the A.C. Load Line 16:32 The Gain Conundrum! 17:38 Final Comments and Toodle-Oots
==== This Video Series Links ==== Video#1: Load Line Analysis: Foundations youtu.be/-fQotNX3gT0 Video#2: Load Line Analysis: Example #1 - A Simple Common-Emitter Circuit youtu.be/dOv_nsBvYTM Video#3: Load Line Analysis: Example #2 - A Beta Stabilized Common-Emitter Circuit youtu.be/1omZ28NtiI0 Video#4: Load Line Analysis: Answers to Two Poignant Questions youtu.be/ajZB4GRzkOcLoad Line Analysis: Example #1 - A Simple Common-Emitter Circuit (066e2)Electronics for the Inquisitive Experimenter2024-04-03 | In the last video I introduced you to the fundamental concepts for doing Load Line analysis.
In this video I am going to create the D.C. and A.C. Load Lines for a simple Common-Emitter circuit.
I've provided links to all of the videos in this series below the time markers. =============== LINKS ================= LINK to the promised formula sheet: drive.google.com/file/d/1b8tljHzRIe4FMJhVUHsxe6doEuhsQxqB/view?usp=drive_link ======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:31 The Circuit: A Tour 02:24 The D.C. Load Line 02:38 Write the KVL 03:46 Question #1: What is V(CE) when I(C) = 0? 04:47 Question #2: What is I(C) when V(CE) = 0? 05:49 Completing the D.C. Load Line 05:58 Plotting the quiescent operating point. 06:50 The A.C. Load Line 06:51 Preparing the Schematic 07:24 Step 1 - Short D.C. Sources 07:45 Step 2 - Short Capacitors 08:12 Step 3 - Simplify the Schematic 09:16 Step 4 - Write KVL 10:46 Step 5 - Setup the A.C. Load Line Equation 12:28 Step 6 - Calculate and Plot Points 12:38 Question #1 13:22 Question #2 14:07 Complete the A.C. Load Line 14:50 Final Comments and Toodle-Oots
==== This Video Series Links ==== Video#1: Load Line Analysis: Foundations youtu.be/-fQotNX3gT0 Video#2: Load Line Analysis: Example #1 - A Simple Common-Emitter Circuit youtu.be/dOv_nsBvYTM Video#3: Load Line Analysis: Example #2 - A Beta Stabilized Common-Emitter Circuit youtu.be/1omZ28NtiI0 Video#4: Load Line Analysis: Answers to Two Poignant Questions youtu.be/ajZB4GRzkOcLoad Line Analysis: Foundations - What is what and How is that? (066e1)Electronics for the Inquisitive Experimenter2024-04-03 | In this video I will answer the questions: 1. What is this graph I am looking at all about? 2. What is the anatomy of a transistor curve? 3. What is a Load Line? 4. What types of Load Lines are there? 5. What are the standard conventions used in all of this?
I've provided links to all of the videos in this series below the time markers.
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:22 What is this graph all about? 03:41 The Anatomy of a Transistor Curve 06:47 What is a Load Line? 07:17 What are the types of load lines? 08:40 What are the standard conventions? 10:02 Final Comments and Toodle-Oots
==== This Video Series Links ==== Video#1: Load Line Analysis: Foundations youtu.be/-fQotNX3gT0 Video#2: Load Line Analysis: Example #1 - A Simple Common-Emitter Circuit youtu.be/dOv_nsBvYTM Video#3: Load Line Analysis: Example #2 - A Beta Stabilized Common-Emitter Circuit youtu.be/1omZ28NtiI0 Video#4: Load Line Analysis: Answers to Two Poignant Questions youtu.be/ajZB4GRzkOcThree Ways to Measure the Output Impedance of a Circuit or Device (066d2)Electronics for the Inquisitive Experimenter2024-03-20 | I had to measure the output impedance of the circuit I designed in the video on the multi-stage amplifier example. It occurred to me that not everyone might know how to make this measurement. So, in this video I am going to show you how we go about doing this. I will also explain the basis of these three methods. This is not just a "do as I do" video. It is an "understand what I do so you can do it, too" kind of video. WAY#1: The Direct Loading (Single Point) Method ... the simplest, but doesn't always apply. WAY#2: Modified Single Point Method ... this works for all the WAY#1 cases and covers most of the rest. WAY#3: Two-Point Method ... this takes care of the remainder...works in ALL cases, but takes more time. I have created a "go-along-with-the-video" sheet which steps through the whole process exactly as I am presenting it here. The link to this sheet is below.
I've provided links to all of the videos in this series below the time markers.
=============== LINKS ================= LINK to the promised formula sheet: drive.google.com/file/d/1QHiVoe75p8Ki4sYhaaPTICfOUDPALVcX/view?usp=sharing ======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 00:59 What is Output Impedance? 01:13 The Output Model 02:18 WAY #1: Direct Load/Single Point Method 05:09 WAY #2: Modified Single Point Method 08:59 WAY #3: Two Point Method 12:48 Concluding comments and Toodle-Oots
==== This video Series ==== Video#1: Introduction to the Junction Diode (How PN junctions work) youtu.be/QkWjh6lGlss Video#2: Introduction to the Bipolar Junction Transistor (BJT) youtu.be/k0C7Zns4imc Video#3: Basic Bipolar Junction Transistor (BJT) Metrics for the Experimenter youtu.be/D-Vi4WJ4Jcc Video #4 Basic Bipolar Junction Transistor Analysis: The Model youtu.be/ef42KZNsOHk Video #5 Basic Bipolar Junction Transistor Analysis: The Common-Emitter Circuit youtu.be/unkBcz1-nLo Video #6 Basic Bipolar Junction Transistor Analysis: The Common-Collector Circuit youtu.be/WZcCYgiGdd8 Video #7 Basic Bipolar Junction Transistor Analysis: The Common-Base Circuit youtu.be/zBBuKWwjKq0 Video #8 A Beta Stabilized Common-Emitter BJT Circuit: Analysis & Design youtu.be/q-O8A5R1PV8 Video #9 A Beta Stabilized Common-Emitter BJT Circuit: Part Selection, Reverse Engineering and Bench Results youtu.be/nP2EWvdlvTQ Video #10 A Multi Transistor Example Ciruit youtu.be/-fd55FFHup4 Video #11 Three Ways to Measure the Output Impedance opf a Circuit or Device *** This video ***A Multi-Transistor Example Circuit Analysis & Design (066d1)Electronics for the Inquisitive Experimenter2024-03-06 | In direct response to requests for me to analyze and design a mutli-transistor amplifier, I present to you this video in which I will design a two-transistor amplifier with the following target characterstics: ** Input Impedance = 10 KOhm ** Output Impedance = 10 Ohms ** Gain = 10 ** Vout (D.C.) = Vcc/2 ** Vcc = 12 Volts In this video I will be using Kirchhoff's Voltage Law and Thevenin's Theorem to accomplish this task. If you are not familiar with these, I've provided links to my videos on these subjects, below. I will also be using Kirchhoff's Current Law. A link to a video on this subject is also provided below. I have created a "go-along-with-the-video" sheet which steps through the whole process of analysis and design exactly as I am presenting it here in this sheet. The link to this sheet is below.
I've provided links to all of the videos in this series below the time markers.
======================================= Time Markers for Your Convenience ---------------------------- 00:05 Introductory Comments 01:30 Defining Our Overall Goals 02:21 Defining Our Hardware Architecture 02:34 The Input Side 04:24 The Output Side 05:33 The Design Process: The Output Side 05:44 Calculate I(BQ) 07:22 Calculate Re2 08:10 Calculate R22 11:09 The Design Process: The Input Side 11:39 Working with Zin 13:04 Piece #1: R11||R21 16:48 Piece #2: r(pi) 17:28 Piece #3: Re1a 25:25 Calculate the Base Current 27:41 Calculate the Values of our Three Pieces 27:49 Piece #1: R11||R21 28:13 Piece #2: r(pi) 28:33 Piece #3: Re1a 29:02 Calculate Re1b 31:59 Calculate Rc1 34:11 Calculate R11 and R21 34:19 Calculate R11 38:13 Calculate R21 39:15 Bench Results 40:15 Final Comments and Toodle-oots -----------------------------
==== This video Series ==== Video#1: Introduction to the Junction Diode (How PN junctions work) youtu.be/QkWjh6lGlss Video#2: Introduction to the Bipolar Junction Transistor (BJT) youtu.be/k0C7Zns4imc Video#3: Basic Bipolar Junction Transistor (BJT) Metrics for the Experimenter youtu.be/D-Vi4WJ4Jcc Video #4 Basic Bipolar Junction Transistor Analysis: The Model youtu.be/ef42KZNsOHk Video #5 Basic Bipolar Junction Transistor Analysis: The Common-Emitter Circuit youtu.be/unkBcz1-nLo Video #6 Basic Bipolar Junction Transistor Analysis: The Common-Collector Circuit youtu.be/WZcCYgiGdd8 Video #7 Basic Bipolar Junction Transistor Analysis: The Common-Base Circuit youtu.be/zBBuKWwjKq0 Video #8 A Beta Stabilized Common-Emitter BJT Circuit: Analysis & Design youtu.be/q-O8A5R1PV8 Video #9 A Beta Stabilized Common-Emitter BJT Circuit: Part Selection, Reverse Engineering and Bench Results youtu.be/nP2EWvdlvTQ Video #10 A Multi Transistor Example Ciruit *** This video ***