0:00 Intro 1:21 I/Q based transmitter block diagram 2:54 Schematic walkthrough for Transmit mixer 6:35 Board populated with supply, ESP32 and ES8388 7:58 Phase Shift testing 10:06 Arduino software walkthrough 11:49 Adding a low pass filter in software and retesting 13:41 Walkthrough of microphone and connections 15:33 Microphone preamp circuit 16:44 Microphone preamp board 17:24 Preamp board populated 17:59 Testing the preamp board on the oscilloscope 19:47 Connecting the microphone/preamp to the transmit mixer 21:06 Looking at the 0/90 degree shifted audio from microphone to oscilloscope 22:33 Wrap up and next video description
0:00 Intro 1:21 I/Q based transmitter block diagram 2:54 Schematic walkthrough for Transmit mixer 6:35 Board populated with supply, ESP32 and ES8388 7:58 Phase Shift testing 10:06 Arduino software walkthrough 11:49 Adding a low pass filter in software and retesting 13:41 Walkthrough of microphone and connections 15:33 Microphone preamp circuit 16:44 Microphone preamp board 17:24 Preamp board populated 17:59 Testing the preamp board on the oscilloscope 19:47 Connecting the microphone/preamp to the transmit mixer 21:06 Looking at the 0/90 degree shifted audio from microphone to oscilloscope 22:33 Wrap up and next video descriptionAY-3-8910 with ESP32 and NanoNA5Y2023-10-01 | In this video I play around with the AY-3-8910 programmable sound generator using an ESP32 and Arduino Nano
0:00 Intro and device background 3:00 Simple demo tune 3:56 Schematic walkthrough 6:15 The bus control lines 8:05 Simple tone example code and demo 11:37 Noise example code and demo 13:51 Obtaining tunes and Tunes demo 16:50 Wrap upSDR Transceiver - Part 7 New BoardNA5Y2023-07-05 | As I mentioned in the last video I was awaiting a new board that I had redesigned. I build up the Tayloe detector and see if the redesign removes the audio artifacts I encountered last time
0:00 Intro and New Board walkthrough 1:50 Power Supply, ESP32 and Codec installed 2:51 si5351 Installed 3:12 Tayloe Detector installed and tested 4:22 Testing the SSB output (excuse the dirty scope - lots of pollen about!) 6:58 Looking at the unwanted sideband supression in dBs 10:03 Wrap upSDR Transceiver - Part 6 Quick UpdateNA5Y2023-06-23 | I think a redesign of the board is in order - but I wanted to provide a quick update as I had been quiet on this project for a while.ESP32 and PCM3060 with Arduino Audio ToolsNA5Y2023-06-04 | In this video I get the PCM3060 audio codec working integrating it both with Arduino Audio tools and the ESP-IDF
0:00 Intro 0:40 PCM3060 description 3:10 PCM3060 connected to ESP32 I2C 4:24 First testing the I2C connection 6:19 Schematic for I2S for audio output 8:39 Audio output on the board 9:42 Walkthrough of ESP-IDF code 13:43 Audio Output with Arduino Audio Tools 16:03 Arduino Audio tools example on the board 17:19 Schematic for Audio Input + Audio Output 17:57 Audio Input/Output on the board 18:30 Why two boards? 20:47 90 degree phase shifted output 21:55 Code changesProducing double sided PCB with UV Resist MethodNA5Y2023-05-17 | In this video I show the method I use to produce PCBs using photosensitive dry film
Kicad - kicad.org Laminator - nothing special here as you don't need high heat - a simple Iron would do also Laser Printer - Brother HL-2300D (ink jet wont work) Old Picture Frame
0:00 Intros 1:29 Materials needed 5:28 The process in a nutshell 7:00 Printing the Transparencies 10:40 The transparencies 11:44 Doubling up the transparencies 12:00 Aligning transparencies front and back 13:11 Using an old picture frame to sandwich the board 14:12 Laminating the photosensitive dry film to the copper board 17:00 Exposing the board to UV 19:26 The exposed board - and removing the protective film 20:37 The sodium carbonate bath 23:45 Etching the board **** DANGER - PLEASE USE GOGGLES and GLOVES **** 24:23 The etched board 25:33 Removing the film with sodium hydroxide **** DANGER - PLEASE USE GOGGLES and GLOVES **** 27:00 The completed board 27:31 The completed board under the microscopeSDR Tranceiver - Part 5 More TroubleshootingNA5Y2023-05-14 | More Receiver troubleshooting (without much luck unfortunately)
0:00 Probing before Audio Switch 2:00 Adding more decoupling caps 3:30 Replacing the FST3253 5:26 Byassing the Audio Switch 6:55 Looking at the ESP32 Header 8:44 New header board arrive - does it fix the problem?Flying around the houseNA5Y2023-05-05 | ...SDR Transceiver Part 4 Receiver ... and a problemNA5Y2023-04-29 | I this video I continue the SDR Transceiver series moving on to the Receiver
0:00 Recap and Intro 1:28 Board walkthrough 3:04 Another problem on the board 3:57 Testing Encoders 5:49 RF Switch 9:47 Installing the Band Pass Filter 11:34 Tayloe detector installed 12:15 Testing Tayloe detector 15:20 Testing sideband supression 16:48 Seeing the sideband suppression in FFT mode on scope 18:52 Some problems on the board 21:18 Comparing to the previous board (link above) 22:48 Not on the air! Troubleshooting to come (suggestions welcome)Some si5351 Hackery and the Tayloe at 150MHz - FAIL!!NA5Y2023-04-16 | In this video I continue with the attempt to use my Tayloe Detector with a 150MHz input signal from my previous video youtube.com/watch?v=VowKRMcVrFk&t=4s
0:00 Intro 1:00 Success with 150 MHz quadrature output from si5351 2:08 si5351 Block diagram 4:33 Worked example for output of signal from si5351 at 20MHz 11:09 Changes I had to make to get quadrature output at 150Mhz 14:01 Testing at 20MHz input RF 16:00 Testing at 40Mhz 16:46 Testing at 60Mhz 17:51 Testing at 80Mhz - oh dear 19:46 Testing at 100 MHz and wrapupBear in the yardNA5Y2023-04-05 | ...Playing around with Tayloe Detector at 150 MHzNA5Y2023-03-22 | I had someone ask me whether my Tayloe detector board youtube.com/watch?v=7t8avIT31Mo
Could work at 150MHz. I thought it might be interesting to have a go at that challenge starting with the band pass filter.
0:00 Intro 1:09 Modelling the BPF in LTSpice 2:09 Resonance Calculator 3:58 BPF in AC analysis 4:38 Undercoupling and overcoupling 6:29 Using toroids.info to build the inductor 7:47 First look on the spectrum analyzer - band pass frequency too low 11:07 Changed the resonator turns - second lookSDR Transceiver - Part 3 Audio and TR SwitchNA5Y2023-03-12 | In this video I continue the SDR Transceiver series moving on to the Transmit/Receive and Audio switches
0:00 Intro 1:07 Note on problems encountered with ESP32-A1S 2:33 Recap on ESP32-A1S GPIO config 3:45 Audio Out - where I will be probing on the circuit 4:19 Audio Output from the board 5:27 Testing Audio In (and comparing to a professionally made board) 8:09 Installing the FST3257 Audio Switch and PTT switch 10:08 Testing T/R voltages 11:05 Testing Audio Switch Output 14:07 Testing Audio Switch Input - approach 15:46 Testing Audio Switch - setup 16:17 Audio Switch for RX 17:29 Audio Switch for TX 19:40 Wrap up and Next StepsSDR Transceiver - Part 2 Board Walkthrough and ESP32 setupNA5Y2023-02-25 | In this video I continue the SDR Transceiver build from my last video: youtube.com/watch?v=d4cmGwFpQcw
In this video I install the power supply, ESP32-A1S and si5351 and do some testing (and find some problems)
Here's the github repo for the board (and I have updated the circuit to fix the problems I've encountered): github.com/thaaraak/SDR-Transceiver
0:00 Intro and Kicad Board Walkthrough 3:03 PCB Walkthrough 4:03 Quick Note on Scope repair - thanks Siglent (no affiliation of course) 4:23 Board drilled 5:33 Power Supply and programming circuitry done 6:31 First program 7:42 installing si5351 (and another problem) 9:00 Wrap up and next stepsSDR Transceiver - Part 1 Overview and Transmit/Receive SwitchingNA5Y2023-01-06 | In this series I will combine the Receiver and Transmitter into a single transceiver with transmit/receive switching
0:00 Walkthrough of transceiver block diagram 1:53 RF Switch and Audio Switch highlights 2:41 Receive Path 4:45 Transmit Path 6:28 Audio Switch Details 7:41 FST3257 Datasheet walkthrough 8:58 Audio Switch implementation 10:18 Audio Switch testing 11:07 Audio Switch on the breadboard 15:43 RF Switch schematic 17:51 Relays that will be used 18:34 Wrapup and next stepsESP32 Based SDR Transmitter - Part 4 Transmitter on the AirNA5Y2022-12-28 | In this video I get the transmitter on the air and test the output in the lab and hear the output using a PA based websdr.org endpoint.
0:00 Intro 0:59 Designing the filters using rf-tools 2:45 Looking at the lowpass filter in ltspice 4:29 Looking at filter input impedance 6:13 Looking at the filter on the spectrum analyzer 7:34 Looking at a 14 MHz bandpass filter in ltspice 9:07 14 MHz BPF on spectrum analyzer 9:51 A bit of a diversion into toroid winding and the effects... 13:28 Testing setup 15:10 Single tone on oscilloscope 16:05 Two tone test 16:57 Single tone on spectrum analyzer 18:28 Two tone on spectrum analyzer 20:04 Changed to 7 Mhz - confirming that LPF is removing harmonics 21:21 Finally transmitting. Results received by K3FEF websdr endpoint 22:39 Wrap up and next stepsESP32 Based SDR Transmitter - Part 3 BPF, Preamp and fixing some Amp problemsNA5Y2022-12-19 | This is the third video in the SDR transmitter series and in this video I move on to the bandpass filter after the Tayloe Encoder as well as building up a little preamp to raise the signal up to that required by the Amplifier. I don't get to installing the amplifier and LPF in this video but I do some troubleshooting with a broken QRP Labs 10W amplifier
0:00 Intro 01:04 Bandpass Filter Schematic 02:07 BPF Board populated 03:23 BPF on the Spectrum Analyzer 04:06 BPF installed after the Tayloe Encoder on the oscilloscope with single tone 04:55 Comparison to signal without BPF 05:37 Comparison with two tone test 06:20 A view on the spectrum analyzer 08:27 The amplifier I will be using 09:21 Oh oh - I broke the amplifier! Some troubleshooting 11:05 IRF510s pulled from board 11:37 More blown components found 12:52 Amplifier back working again and testing the output on the scope 14:44 A quick look at the input impedance of the Amplifier using the minivna 15:50 Preamp schematic 16:36 Preamp board 17:09 Preamp board populated and testing out of circuit 18:24 Preamp installed after BPF and tested 21:39 Wrapup and next stepsESP32 Based SDR Transmitter - Part 2 Tayloe EncoderNA5Y2022-12-12 | In this video I continue the transmitter series and move on to the Tayloe Encoder which mixes the I and Q audio signals together with the LO to produce a sideband signal (either upper or lower)
0:00 Intro 0:54 Schematic walkthrough 2:20 I/Q to 0/90/180/270 opamps installed 03:25 0/90/180/270 audio signals tested 04:49 A diversion into some interesting patterns produced with quadrature audio signals 06:50 Tayloe Encoder installed 09:13 Looking at the code to swap upper and lower sideband output 10:15 Testing the output signal on the oscilloscope 13:36 Looking at a single tone SSB signal on the spectrum analyzer 15:31 looking at the effect of adjusting the I/Q balance 17:15 Looking at a two tone SSB signal 18:22 Looking at the out of band harmonics and wrap upPassive IR Sensor circuit Reverse EngineeringNA5Y2022-11-16 | In this video I take an old passive IR sensor board, reverse engineer the sensor and amplifier and create a homebrew version of the amplifier.
0:00 Intro 00:54 A look at the sensor board 03:09 The sensor and amplifier schematic 07:09 A look at the original board output on the oscilloscope 08:01 Looking at the same on the homebrew circuitHomebrew si5351 BoardNA5Y2022-11-09 | I had been meaning to create a homebrew version of the si5351 boards that Adafruit and others sell. This is a quick video going through that build
0:00 Intro 1:14 The circuit 2:09 The board built 2:35 Testing and wrapupESP32 Radio on a Board - Part 3 Final Build and on the AirNA5Y2022-10-31 | In this video I get the Radio completed and on the air.
0:00 Bandpass filter install 2:22 Bandpass filter tested 3:44 Splitter installed and tested 6:16 FST3253, Opamp and Vias installed 7:03 First test - Injecting a 14.2 MHz signal - audio out on oscilloscpe 9:00 Listening to the injected signal 10:01 Looking at the unwanted sideband supression 11:25 On the air on 20 meters 13:48 Wrap upESP32 Radio on a Board - Part 2 Audio InterfaceNA5Y2022-10-24 | This is the second part of the ESP32-A1S Radio I started here: youtube.com/watch?v=redvZ7LcXT0
0:00 Intro 0:35 Audio Interface on the Board 2:03 Testing the board using the SineWaveGenerator 3:58 A problem discovered with audio output 6:01 Testing Audio Input to Output - and another problem 7:43 Input problem fixed? 8:19 Testing Audio I2S In to Audio I2S OutESP32-A1S Radio on a Board - Part 1NA5Y2022-10-22 | In this video I create a board for the SDR I previously did in this video: youtube.com/watch?v=prCrbD4T6I4&t=1s
0:00 Intro and Board Walkthrough 1:37 Schematic walkthrough (apologies again for the low piched hum) 4:22 Build Order 6:18 Power supply circuitry on the board and tested 8:30 A problem with the RX/TX lines 9:50 RX/TX lines fixed 10:38 ESP32-A1S installed on the board 11:30 First program flashed 13:28 si5351 installed and tested 15:20 Wrap upSpace Invader Sounds Part 2 - The SN76477NA5Y2022-10-15 | In this video I continue the series started with youtube.com/watch?v=haHSgdZHHwc&t=204s
and have a look at the Retro Audio SN76477 Complex Sound Generator IC from Texas Instruments.
0:00 Intro and SN76477 description 0:50 Source documents 1:48 Block diagram and SN76477 capabilities walkthrough 4:44 Examples walkthrough 5:11 The classic UFO sound from Space Invaders 7:53 UFO sound on the breadboard 9:36 Attack and Decay Envelope control 11:42 Attack/Decay on the Breadboard 14:15 Noise Generation 16:11 Noise Generation on the BreadboardRetro Audio - Space Invaders Sound Effect CircuitsNA5Y2022-10-07 | In this video I will be playing around with some old sound circuits from the classic Space Invaders machine.
0:00 Intro 0:24 The schematics for the Taito game 1:30 Quick note on the LM3900 Norton OpAmp 4:14 Invader Stepping sound circuit 7:05 Stepping sound on the breadboard 8:09 Stepping sound audio 9:00 Step sound on the oscilloscope 9:45 Noise generator schematic walkthrough (sorry about the background hum) 11:57 Noise generator on the oscilloscope 13:58 Noise sent to the audio output 14:57 Player killed schematic walkthrough 15:49 Setting the sustain time impulse 17:39 Attack and decay circuit 18:30 Attack and decay on the oscilloscope 21:31 Combining the envelope with noise 22:25 Explosion sound on the oscilloscope and wrap upQDX - Low Output - Blown BS170sNA5Y2022-08-29 | Just a quick video replacing some blown FETs in the output stage of the QDX70W Amplifier - Using RD16HHF1NA5Y2022-08-22 | In this video I replace the IRF530s from the previous video youtube.com/watch?v=GExwAZttFa8&t=946s
0:00 Intro 1:38 Input SWR Measurement 3:48 Amplification of CW input 5:06 Two tone test70W Amplifier from eBay - Spinning my own BoardNA5Y2022-08-16 | This video is a followup from my earlier video on the "70 Watt" amplifier from ebay youtube.com/watch?v=JgiakIxMjfI&t=85s
I do a shoutout to kitandparts in the video - no affiliation but they are a great source for all your toroid and binocular needs http://kitsandparts.com
0:00 Intro 0:40 Changes between my board and the original 3:15 Schematic walkthrough of the board 5:38 Walkthrough of the built up board 9:25 Input SWR testing 12:20 Testing CW through the amplifier 13:41 Look at the effectiveness of the LPF 14:34 Two tone test setup 15:12 Two tone on the oscilloscope 17:02 Two tone on the spectrum analyzer 20:46 Replacing the FT50-43 with Ferrite Tube 22:42 Replacing the FT50-43 with BN 43-7150 25:27 Wrap up (I didn't get to testing the RD16HHF1s - more to come)Summer walk with OliverNA5Y2022-08-12 | No talking just a walk in the local forest with OliverQDX Fix - Blown Q7NA5Y2022-07-30 | Quick fix video for a blown Q7 in the QDXSoldering an SMD ElectrolyticNA5Y2022-07-16 | Just a quick video showing how I solder down SMD electrolyticsQRP-Labs QDX Kit Build - TransmitterNA5Y2022-07-14 | In this video I complete the earlier receiver build youtube.com/watch?v=KmpNxhZiJXg&t=1967s
0:00 A quick diversion into the QDX Bandpass filter 4:42 Walkthrough of transmitter build components 6:14 Winding the output transformer T1 11:53 Installing L4 the RFC coil 12:29 BS170s installed 12:58 On the air on 20m with the oscilloscope monitoring output - first contact 15:59 Calling CQ on 40m 18:36 Trying 3:3 turns ratio on T1 and wrapupQRP-Labs QDX Kit Build - ReceiverNA5Y2022-07-10 | In this video I build the receiver portion of the QDX digital radio from QRP Labs qrp-labs.com/qdx.html
0:00 Intro and QDX description 1:00 Walkthrough of board 2:27 A look under the microscope 4:18 Walkthrough of schemartic 7:36 My build order (done at my own risk ;) ) 11:07 uController up and running 13:40 Quick walkthrough of LPF switching 16:17 Building the LPF 17:10 Winding the LPF toroids 18:00 Testing the LPF toroids 16:35 Installing L12 the multi-tap bandpass inductor 23:08 Winding the Trifilar splitter T2 26:06 Determining T2 leads 28:46 *** On the Air *** 30:40 Doing some voltage measurements - LPF 32:47 Testing X5 33:57 Testing X6 34:45 Walkthrough of WSJTX setup and wrapupUsing the MAR 6 as a PreampNA5Y2022-07-02 | In this video I use the MAR-6 monolithic smplifier minicircuits.com/pdfs/MAR-6+.pdf
0:00 Intro 0:23 Walkthrough of datasheet and application circuit 1:53 Walkthrough of physical device 2:44 Walkthrough of MAR-6 preamp board 3:56 Test setup and testing various frequency/amplitude combinations 7:32 How the preamp is connected to the Tayloe board 8:10 Preamp mounted on the board 9:21 Testing the audio output at various input amplitudesSimple SDR - Updated FIR implementationNA5Y2022-06-23 | This video is an update to the earlier SDR video: youtube.com/watch?v=prCrbD4T6I4
In this video I create a new FIR implementation which uses the ESP-DSP assembler implementation: github.com/espressif/esp-dsp
Just download the Bounce2 and Encoder libraries using the Library Manager - I didn't modify those
0:00 Intro (sorry for all the banging...) 0:36 Block diagram walkthrough - Tayloe Detector 1:55 Block diagram walkthrough - ESP32 Processing 4:44 Using the si5351 with code example 6:53 si5351 in action 8:07 Audio Phase Shifting 10:32 Demo of what happens with too many taps 11:43 Schematic walkthrough of the Radio 14:36 Walkthrough of Radio components 15:48 Radio with injected RF at -70 dBm 17:15 Looking at the sideband suppression on the oscilloscope 18:55 Walkthrough of the Radio.ino code 24:30 Finally on the air...ESP32 A1S with Arduino Audio ToolsNA5Y2022-06-12 | This is a followup to my previous video youtube.com/watch?v=bEPe8Pm1mdw&t=1s
0:00 Intro 1:51 Quick walkthrough of ES8388 Arduino library 2:33 Example 1: Generated Stream to I2S (streams-generator-i2s) 5:27 Example 2: I2S Input to I2S Output (streams-i2s-i2s) 7:20 Example 3: Generated Stream to Browser (streams-generator-webserver_wav) 9:34 Example 4: I2S Input to Browser (streams-i2s-webserver_wav) 13:34 Example 5: Audio to Bluetooth Receiver (basic_adp_sink) 15:50 WrapupPlaying around with the ESP32 A1S ModuleNA5Y2022-05-21 | In this video I do some playing around with the ESP32-A1S module which has an ESP32 uController and an ES8388 audio codec on board.
0:00 Intro 1:20 A look at the ESP32-A1S device 2:25 How to tell the ES8388 and AC101 varieties apart 3:20 A look at the ESP32-A1S under the RF Can 4:16 The pins available 6:01 The module with soldered connections 6:32 How to program the board using a USB to Serial adapter 7:58 A schematic walkthrough showing connections 9:38 The Pins used to connect between ESP32 and ES8388 10:33 Walkthrough of the module on a protoboard 11:32 The simple sine wave example in code 12:52 The simple sine wave example in action 13:44 Phase shift example in code 17:17 The simple sine wave example in action 19:25 WrapupQuick Update from New HampshireNA5Y2022-04-26 | Just a quick video showing the progress with the workshop. Lots more boxes to unpack and stuff to setup!Channel UpdateNA5Y2022-03-06 | Thought I'd post a quick channel update. I will be moving to New Hampshire from Texas and I will be taking a break as I move and get the new home setup. I'll certainly be around for any questions and comments and hope to get back in action June timeframe.
Thank you all for the subscriptions, comments and likes and hope to see you all again soon!
Regards
ian NA5YESP32 Arduino with arduino audio toolsNA5Y2022-02-19 | Update: I mentioned that I have been unable to find a replacement for the Iowa Hills FIlter software. Since creating this video I was able to solve that problem. See here youtube.com/watch?v=BUGQaTJ6aWI&t=166s
0:00 Intro 1:30 Hardware setup and connections 3:30 I2S Pin configuration detail 5:10 Sine wave generator to I2S - code 6:59 Sine wave generator to I2S - in action 8:05 I2S input Stream to I2S output Stream - code 9:22 I2S input Stream to I2S output Stream - in action 11:45 FIR Filter (90 degree phase) - code 13:29 FIR Filter (90 degree phase) - in action 14:58 FIR Filter (low pass/high pass) - code (with a quick note on the coefficient derivation) 16:16 FIR Filter (low pass/high pass) - in action 17:54 Wrap upHilbert FIR Filter for 90 Degree Shift using PythonNA5Y2022-02-19 | I have been looking for an alternative to the awesome Iowa hills filter software for some time to generate the FIR coefficients for 90 degree phase shifting. I came across this video youtube.com/watch?v=b5DevnKMpDo
Which explains in steps how to create a Hilbert filter and associated delay line using Matlab.
This video is a quick walkthrough of that code and a demonstration of the filter created using my previous ESP32 based audio processing here: github.com/thaaraak/ESP32-IQ
0:00 Intro and why I am looking for an alternative to Iowa Hills 0:53 The Hilbert Filter + Delay Line approach 2:00 Python Hilbert generator Code walkthrough 4:22 Creating a sample filter 5:05 Looking at the frequency response of the filter 5:35 Convolving a sample sine wave through the Hilbert and Delay line 7:21 Using the coefficients created in an ESP32 based audio processor 8:19 Looking at the output on the oscilloscopeMC1496 Modulator and MixerNA5Y2022-01-27 | In this video I do some playing around with the old school MC1496 Mixer and Modulator IC.
UPDATE: I have just realised that I drew the schematic wrong at the output. I should have had the transistor base connected below the load - not above. I'll correct the schematic on github
0:00 Intro 0:24 MC1496 Data sheet and applications 1:47 Schematic walkthrough 5:24 A look at the board and test setup 6:03 7 MHz carrier and 1 KHz modulating signal on the oscilloscope - AM 7:00 Double Sideband suppressed carrier output 7:25 Looking at the frequency content of DSBSC and AM signals 8:27 Mixing a pair of Audio signals 9:40 Looking at the frequency content of the mixed audio signalsESP32 Temperature Sensing with MAX31865 and TMP36NA5Y2022-01-08 | In this video I hook up a pair of sensors: TMP36 and MAX31865 to the ESP32. No affiliation with any of the vendors below.
0:00 Intro 0:49 The TMP36 2:27 The MAX31865 4:57 The PT100 temperature probe 5:56 Schematic for both connected to ESP32 7:16 Walkthrough of components on breadboard 8:01 Running the code 8:47 Dunking the probe in hot water 9:19 Looking at the SPI interactions on the oscilloscope 10:10 Looking at a temp read SPI call on the oscilloscope 11:40 Some problems encountered with SPI 14:00 Code walkthrough for ESP-IDF SPI (apologies for low volume) 15:23 The temperature calcs for TMP36 and MAX31865 18:20 A question on reusing Arduino libraries in ESP-IDF 19:45 Wrapup70 Watt Amplifier - Two Tone testNA5Y2021-12-30 | Just a quick followup from the previous video youtube.com/watch?v=JgiakIxMjfI&t=104s
Where I do the two tone test against the 70 W amplifier kit. Funnily enough just after I finished the video two more IRF530s gave their lives - next vid will definitely have the temperature protection in.
0:00 Intro 1:08 Test Setup with Magnis as Exciter 3:01 Two tone with Magnis as Baseline 3:50 Magnis on Spectrum Analyzer 5:19 Two tones not quite Pure? 5:39 Two tone from the Amplifier 7:00 Amplifier on the Spectrum analyzer 8:44 Close up of Amplifier and other mods to do 11:31 Some tests with a 15 ohm resistor at R6 (see schematic link) 11:54 on the oscilloscope 12:23 and on the spectrum analyzer70 Watt Amplifier Kit BuildNA5Y2021-12-26 | This video is a followup from the ESP32 based exciter I built earlier youtube.com/watch?v=jnVwxNwio8E
0:00 Intro and Component Walkthrough 1:52 Schematic Walkthrough 4:08 Board Walkthrough 5:48 Endcaps removed from board 6:19 Output transformer first end cap 6:59 Ferrite tubes and bushings in place 8:26 Testing continuity 9:00 T/R Relay installed 10:30 Relay and Bias tested 13:59 Input transformer installed 14:39 Electrolytics installed 14:57 IRF530s installed 15:40 Output/Input transformers wound 18:15 feedback resistors installed 18:54 RFC installed 19:24 Excited connections to the Amplifier and test setup 21:55 Final testing on the oscilloscopeESP32 CW TransmitterNA5Y2021-12-22 | Just a quick video today where I build a simple ESP32/si5351 based CW transmitter using a trio of BS170s in the finals. I am assuming most people aren't interested in a code walkthrough - let me know in the comments if you are interested in the code.
0:00 Intro 0:24 Schematic Walkthrough 3:22 Walkthrough of the board 4:49 Waveform on the oscilloscopeMagnis SDR - Part 9 PA and Low Pass Filter and on the airNA5Y2021-12-12 | In this video I wrap up the build, get it on the air and even make a QSO!
0:00 Intro 1:08 A note on RD15HVF1s genuine and otherwise 3:59 Pinout of genuine RD15HVF1 and copy 4:57 T1 Wound and Installed 5:45 T1 tested on the board 7:32 T5 Wound and installed 10:03 T5 tested on the board 10:40 Power supply filtering 12:06 Testing without the Low Pass Filter 14:13 Checking the bias on the mosfets 14:54 Two tone test 16:08 Low pass filters 17:07 Testing with Low pass filters installed 18:47 Getting the magnis on the Air 19:15 Some listening 20:41 A QSO (hope you don't mind me sharing our QSO, John)Magnis SDR - Part 8 Amplifier Driver and BiasNA5Y2021-11-29 | In this video I pull together the amplifier driver and bias circuitry. The amplifier driver centers around a pair of OPA2674 High power wideband opamps - datasheet is here: ti.com/lit/ds/symlink/opa2674.pdf?ts=1637860124805&ref_url=https%253A%252F%252Fwww.ti.com%252Fproduct%252FOPA2674
0:00 Intro 0:37 Driver circuitry schematic walkthrough 1:20 Detail of Op-amp driver and gain 2:20 Bias circuitry on Schematic 3:52 Build and testing order 5:53 Testing the supply to Opamps and to center tap of T4 8:07 OPA2674 Opamps installed and tested 8:55 Output of Opamps on oscilloscope 11:05 Building the bias circuitry 12:12 Q10 p-channel bias switch mosfet installed and tested 13:58 Gate bias circuitry installed 14:58 Gate bias tested 16:12 Confirming on oscilloscope bias is applied to signal from Amp driverMagnis SDR - Part 7 Transmit MixerNA5Y2021-11-24 | In this video I will be building the Transmit mixer which is based on the Tayloe mixer design I have shown in earlier videos such as youtube.com/watch?v=XySzNe7rXbk&t=930s
0:00 Intro and schematic walkthrough 4:10 Board walkthrough for Transmit Mixer 6:08 Testing the Audio Network 7:17 Testing the I/Q audio signals 9:40 Testing the 0/180 degree audio signals 10:43 Transmit Mixer on the board and some troubleshooting 11:42 Test setup for SSB 12:06 Test setup with HDSDR and signal generator 13:22 Testing SSB at 14 MHz 14:28 Testing SSB at 7 Mhz