ceptimusJust a small update to a previous project - it uses an Arduino Nano, or Uno, or similar to decode an SBUS signal and display the values on a 1.3-inch OLED display. See here for the previous video:
youtube.com/watch?v=nSPsJLBgBE4 This version just adds the facility to display either PPM microseconds or channel percentages in place of the 11-bit SBUS values. A push button allows for cycling through the three possible display modes. Note that different manufacturers may use slightly different scaling for the SBUS range - so if you want to tweak the sketch to display exactly 100% for your particular set-up, you may want to edit the scaling values at lines 173 and 178 of the main sbusDecode4.ino file. You can download the sketch from this thread on the Mode Zero forum (free to join): http://mode-zero.uk/viewtopic.php?f=42&t=1010
Arduino SBUS decoder updateceptimus2021-02-02 | Just a small update to a previous project - it uses an Arduino Nano, or Uno, or similar to decode an SBUS signal and display the values on a 1.3-inch OLED display. See here for the previous video:
youtube.com/watch?v=nSPsJLBgBE4 This version just adds the facility to display either PPM microseconds or channel percentages in place of the 11-bit SBUS values. A push button allows for cycling through the three possible display modes. Note that different manufacturers may use slightly different scaling for the SBUS range - so if you want to tweak the sketch to display exactly 100% for your particular set-up, you may want to edit the scaling values at lines 173 and 178 of the main sbusDecode4.ino file. You can download the sketch from this thread on the Mode Zero forum (free to join): http://mode-zero.uk/viewtopic.php?f=42&t=1010Cursor jumping bug of arduino-ide 2.0.0 under Linux Mint 21 Cinnamonceptimus2022-10-12 | You can go to "Command Palette", "Preferences: Open Settings (UI)", and disable "editor.trimAutoWhitespace" to hide this bug and make the IDE usable. I'm just making this quick video to demonstrate the bug, in case it's of any help to the IDE developers. My thanks to those developers, by the way. I'm loving the improvements of the IDE 2 over the previous 1.Read AT89C2051 using Arduino (Nano, Uno, etc.)ceptimus2022-10-05 | Somebody requested this. Not sure why. If the AT89C2051 program hasn't been protected by setting the lock bits, then this Arduino sketch will read and display the chip contents in the Arduino IDE Serial console. It displays in Intel Hex file format, so you can cut-and-paste the data and use it for saving a copy of the chip contents, emailing to someone, disassembling or whatever. Taking a copy of a chip's contents is most useful when you want to write that same program to other blank chips - but if you have a programmer, it would already be able to read chips, so you wouldn't need this! You can download the sketch here: ceptimus.co.uk/AT89C2051read.zipArduino Uno composite video output. 2400 baud dumb terminal.ceptimus2022-09-09 | I modified my sketch from a previous video, so that it can also receive and display serial data at 2400, 8,1,N,N. It uses 3 resistors to drive the composite video signal, and the standard Uno 'serial port' connection to receive data. Has a 46x29 character display (368x232 pixels). Can be tweaked to do slightly larger display, depending on the overscan properties of your monitor. Sketch with instructions can be downloaded from this link: ceptimus.co.uk/UnoVideoSerial.zip Unzip and compile/upload using the Arduino IDE in the usual way. PuTTY is a good free serial client (Windows and Linux) Set to 2400, baud 8 data bits, no parity, no handshaking. Ignore any gibberish displayed by PuTTY (or other terminal program). It's because the transmit data line is actually sending out a video signal at 16 Megabaud - so you wouldn't expect it to display anything sensible when a 2400 baud serial signal is expected. If you need to send back serial data from the Arduino, you'll need to do software driven serial, using some other pin than TX1. An Arduino Mega 2560 is more useful for this sort of work - it has more RAM and four serial ports. So one port can be tied up outputting video, and there are still three free ones to handle communication.Battery tester demo including calibration procedure.ceptimus2022-08-17 | I made some battery checkers for checking the rechargeable receiver batteries in model gliders or i.c. powered planes before flying. The checker uses one of those Arduino clones: an LGTF328P SSOP 20 miniEVB. I also designed and 3D-printed the case - the top and bottom just clip together, without glue. Files, build instructions, etc. available on the Mode Zero forum (free to join): mode-zero.uk/viewtopic.php?f=42&t=1562Using Arduino as ISP to program AT89S52ceptimus2022-07-11 | I demonstrate how easy it is to use a standard Arduino (UNO, or NANO, etc.) as an ISP to program an Atmel AT89S52 chip or similar. I show how to do it using either Windows or Linux. (files in download links, below).
Note that this technique won't work for the AT89C52 or other 'C' chips - they require a 'high voltage parallel programmer' - only the 'S' chips have the SPI programming interface. The 'S' chips are pin compatible and code compatible with the 'C' chips, so if you have a device with a 'C' chip, you may consider swapping to an 'S' chip, rather than buying or building a dedicated programming device.
I also demonstrate the 'rotating LED clock kit' displaying temperature in both Celsius and Fahrenheit, and playing music. (hex file in links below). I show how to set the clock back to its original software (provided in the links below) and how to download whatever program is already in the chip (providing it has not been write-protected).
The clock plays a recognizable tune using the standard active buzzer, but it sounds a bit nicer if, like I have, you swap it for a passive buzzer (they're the same size, so it's a simple soldering job to swap).
Arduino sketch: ceptimus.co.uk/ArduinoISP_AT89S52.zip Windows files: ceptimus.co.uk/AT89S52windows.zip Linux files: ceptimus.co.uk/AT89S52linux.zipRotating LED Electronic Clock Kit EC1204B. Now with music!ceptimus2022-07-06 | I wasn't a big fan of the 'hourly chime' or alarm beeper, but some people asked me to make it do something...Radio control (four channel proportional) using two Arduinos with nRF24L01+modules .ceptimus2022-07-02 | This is using Phil Green's software. For download, diagrams, discussion and more, see the thread on the Mode Zero forum: mode-zero.uk/viewtopic.php?f=42&t=971 I was using two of the LGT8F RF-NANOs, available from Ali Express, but you can use any of the popular Arduinos (Nano, Uno, etc.) and any nRF24L01+ modules. If you're going to fly using it, I recommend getting (for the transmitter side) an nRF24L01+ module with a power amplifier built in and which uses an external antenna.Carrier Wave transmission test of the LGT8F RF-NANOceptimus2022-06-30 | Just to prove that the thing actually transmits! Yes, it does have an nRF24L01+ chip, not the 'nonplussed' variety! Is it a genuine Nordic chip, or a working clone? Who can tell?Using one LGT8F328P chip as an ISP SWD programmer to program another.ceptimus2022-06-29 | This is using the work of David Buezas, especially brother_yan, and others. See github.com/dbuezas/lgt8fx for the original. Here's the details of how to program the programmer: ceptimus.co.uk/index.php/2022/06/29/lgt8f328p-isp-programming Best plan is to get two of the Nano-style boards, use one as a programmer to program the same program to the other: the second one then becomes a dedicated programmer where you can't accidentally overwrite its own program.Rotating LED Electronic Clock Kit EC1204B. Alternative program.ceptimus2022-06-27 | I reprogrammed the chip to make the operation simpler (and better?) I did it in C, using the excellent, and free, SDCC compiler. Let me know in the comments if you have suggestions for improvements or additions (there's plenty of room in the chip). I'll make a fresh video showing how to upload my code to the chip (and how to restore the original code too), if anyone's interested.Hourglass clock kit STC15W based. Now with extra patterns.ceptimus2022-06-20 | I reprogrammed the chip to have extra patterns. These patterns don't use EEPROM storage - there's just a bit of code for each pattern. I also improved the multiplexing of the LEDs, and debounced the push button better than the code supplied in the kit. If you only have an STC15W201 chip (1K flash), then you can't have all these patterns, but my code supports the -201 chip anyway - you just can't have all the patterns loaded at once. My kit had an STC15W204 chip (4K flash) and all the patterns demonstrated here only about half fills it. You could double the number of patterns if you care to write them! Here's the source code, hex files for the -201 and -204, and a description of how it works: ceptimus.co.uk/index.php/2022/06/22/led-hourglass-kit-programmingElectronic hourglass LED kit. STC15W201s microcontroller.ceptimus2022-06-13 | My kit was advertised as having a -201s through-hole DIP microcontroller, and 'warm white' LEDs, but was actually supplied with a surface-mount -204s chip and blue LEDs. I actually only bought the kit to get the DIP-chip, because I wanted it as a spare for a robot kit that uses the same item. Never mind: it's always something of a lucky dip when buying these cheap kits from Chinese suppliers.Rotating POV kit from my previous video, filmed using phone for reduced strobingceptimus2022-06-09 | Just a quick look using my phone camera rather than my usual Sony.DIY Rotating Led Kit POV Soldering Training Kit Upgraded Versionceptimus2022-06-09 | The video description is taken from the product description on AliExpress. This video is just a quick look at how mine worked the first time it was powered up. If you're competent at soldering surface mount components, this kit is pretty easy to build - unlike the cheap POV kit I built years ago where you had to solder surface mount LEDs across the edges of PCBs. Also, this one came with the chip pre-programmed and quite useful, as a clock, without any additional programming work. I'll probably write my own code for it in due course, and maybe see if I can get a live data link via infra-red from a Raspberry Pi or similar, so that the display can be updated in real time, without having to stop the rotation and connect a programmer to store fresh images in the rotating chip's memory. Since I posted the video, I found the correct way to set the clock: from mode 1, press the 'play' button (triangle) to start editing the hour; use the + and - keys to adjust, then press play again to store the hour and move on to editing the minute. Repeat the process for hour, minute, second, month, day-of-month. After pressing the 'play' button for editing the day-of-month, the correct time is displayed and the real time clock chip keeps the correct time even when powered down. Don't press the 'menu' button on the remote. This is an undocumented feature that sets the clock to 22:10:00 May 20th. After pressing 'menu' you'll need to reset the clock to the correct time/date again!12864B V2.0 LCD graphics on STC89ceptimus2022-06-02 | I ported my previous Arduino code youtu.be/mAsCE9hiyO4 to the STC89. I used SDCC to compile my code, but if you use Keil, you just need to make some trivial edits. Download the code from ceptimus.co.uk/STC89LCD12864BV2_0.zip12864B V2.0 LCD display. Driver speed increase.ceptimus2022-05-31 | This is a follow up to my previous video: youtu.be/mAsCE9hiyO4 I added some cacheing to the driver. Previously, it was writing the display RAM whenever a pixel changed even when that pixel was in the off-screen invisible double-buffer area. Now, it only writes the RAM when it needs to move to a different group of 16 pixels, or when any changed pixels become visible on the screen. Now it's much faster - too fast, in fact for the liquid crystal response time to reveal the 'ring' moving as in the previous video. So for this demo, I removed the 'erase', so that the display only cycles when the ring has bounced all around the screen and eventually returns to its starting position. Description and code download at: ceptimus.co.uk/index.php/2022/05/30/12864b-v2-0-lcd-module12864B V2.0 LCD display module Arduino democeptimus2022-05-30 | See this video for the new faster driver: youtu.be/kK2_xpoWIhQ Details and a link to download the sketch are here: ceptimus.co.uk/index.php/2022/05/30/12864b-v2-0-lcd-moduleSH-E 879 clock kit reprogrammed as a stopwatchceptimus2022-05-23 | These cheap clock kits available on eBay and AliExpress use an Atmel AT89C2051 microcontroller which runs old school 8051 code. Here, I show how to use the (free) SDCC compiler to repurpose the clock into a slightly more useful stopwatch. Here's my blog about the stopwatch which includes both the source code and the resulting hex files: ceptimus.co.uk/index.php/2022/05/24/sh-e-879-clock-kit-stopwatchArduino 18 channel PWM to SBUS and SBUS to PWMceptimus2022-04-28 | I hooked up eighteen PWM inputs to one Arduino Nano, and eighteen servos to a second Nano. The first Nano samples the PWM and converts to an (inverted) SBUS signal which it outputs. The second Nano decodes the SBUS signal and drives eighteen PWM outputs to control the servos.
It was an interesting coding challenge to get 8-bit Arduinos to do that jitter free and with fast frame rates (about 82 updates per second). Coders may wish to study the sketches which use some pretty advanced techniques such as inline assembly, and direct control of the Serial hardware.
All the sketches are stand-alone and use no libraries. PWM to SBUS: ceptimus.co.uk/PWM2SBUS.zip PWM monitor (use with the Arduino IDE Serial Plotter tool (Ctrl-Shift-L) to get a real-time graph of all 18 PWM inputs (115200 baud): ceptimus.co.uk/PWM18channelMonitor.zip SBUS to PWM: ceptimus.co.uk/SBUS2PWM.zipPWM to SBUS encoder (up to 18 channels) on Arduino Nanoceptimus2022-04-27 | Tomorrow, I'll hook it up to the SBUS to PWM converter with 18 servos connected. If it works okay, I'll upload the sketch for others to try.Reading 18 channels of PWM with an Arduino Nanoceptimus2022-04-27 | Interesting coding challenge to simultaneously read 18 PWM input channels as accurately as possible. The pulse widths vary from about 1ms to about 2ms, and repeat about every 11ms. To avoid jitter, it's necessary to capture timestamps for the rising and falling edges of all 18 inputs accurate to a few microseconds. Printing to the serial port to display the results on the Arduino IDE also causes some interrupt-related jitter. This is work in progress for an 18-channel PWM to SBUS sketch. Arduino IDE sketch: ceptimus.co.uk/PWM18channelMonitor.zipSBUS to PWM decoder on Arduinoceptimus2022-04-23 | Uses a standard AtMega328 Arduino (Uno, Nano, Pro Mini, etc.) to decode an inverted SBUS signal and drive up to eighteen PWM (servo) outputs. Inverted SBUS goes in on RX0, and the PWM outputs are on pins D2 - 13, and A0 - A5. The outputs go in channel order, so the first 8 channels are on D2 - D9. Here's a link to the Arduino sketch: ceptimus.co.uk/SBUS2PWM.zip Here's a link to a previous video of mine showing an SBUS decoder that drives CPPM out, and also provides a human readable display of the channels on a little OLED display module: youtu.be/XBsLfIQPxf4
I misspoke a couple of times when discussing the PWM frame rate. One time I said 'six milliseconds' and another time 'twelve seconds'! It should always have been 'twelve milliseconds' (actually about 12.2) If your receiver outputs SBUS frames slower than every 12.2 milliseconds, then the PWM output rate will sync with those frames: if your receiver outputs SBUS frames faster than every 12.2 milliseconds, then intermediate frames will be ignored, and the servo PWM signal will be sent on every other SBUS frame (or every third frame, etc.)
If the SBUS signal stops, then the decoder will stop outputting PWM signals, this leaves the servos in their last commanded position, until the SBUS signal is restored.Two Servo Clock using Arduino IDE to program ESP8285 (ESP8266 compatible) board.ceptimus2022-04-13 | A simple 3D-printed clock using two servos to drive the hands, and an Arduino-programmable board that connects to WiFi to get the correct time. Total parts cost about ten dollars in April 2022. DIY MORE ESP8285 Mcu Strong. Two 9-gram servos (Tower Pro or similar). The STL files for 3D printing the parts can be downloaded from ceptimus.co.uk/twoServoClock/stlFiles.zip The sketch (Arduino IDE) for programming the microcontroller can be downloaded from ceptimus.co.uk/twoServoClock/twoServoClock.zip The files and photos are also on Prusa printables here: printables.com/model/173810-two-servo-clockComposite video from Arduino UNOceptimus2022-03-23 | Explaining how to generate a fairly high resolution composite video signal from an Arduino UNO (or Nano or similar) using just three resistors. The signal is up to about 380 pixels wide by 270 pixels high. The UNO doesn't have enough RAM to hold bit mapped graphics that size, so you're limited to text or other block-graphic style displays. The Arduino Mega 2560 has much more RAM, and four serial ports (the video generation ties up one of the serial ports), so is better suited to this kind of task. The resistor values aren't that clear because of my scribbly handwriting. The one from pin 1 is 1000 ohms, the one from pin 5 is 47 ohms, and the one from pin 9 is 1200 ohms. You can download the sketch using this link: ceptimus.co.uk/CompositeVideoTerminal.zipGoogle Earth pilots eye view of Ardupilot plane flightceptimus2021-11-03 | Watch at 0.5x speed - for some unknown reason, it's recorded at about 2x actual speed. There's a loop-the-loop at 07:15. This is taking the log file from an Ardupilot flight controller, and then using Google Earth to render the log file into a pilot's eye view movie. I only did this at low resolution, and didn't bother to edit before uploading - so there's some pre-flight logging at the start with nothing much happening. Not sure if it's possible to get rid of the Google Earth map information overlay/watermark - more experimentation needed.APM 3.2.1 Hexacopter short missionceptimus2021-08-21 | Same mission as previous video, but this time I had a camera with a viewfinder! We repeated the mission again later, simultaneously recording the 'goggle' view, but that video was out of focus and unusable. Will maybe make a third attempt using a better recording system.Hexacopter with old-school 8-bit APM Arducopterceptimus2021-08-11 | Test flying Steve Ottley's hexacopter in mission (auto) mode. I was planning to fly the same short mission a second time, this time filming the FPV view through the 'goggle.' Unfortunately, the hexacopter landed right next to the goggle I'd left on the ground at the launch point, breaking one of its flimsy 5.3 Gemfan props against the goggle! I'd not taken any spare props with me, so that video will have to wait for another day. I'll use a camera with a viewfinder next time, and get some in-frame video of the take-off and landing too! Also plan to try the autotune function when we get a calmer day.Terrible cheap toy drone video camera footage example.ceptimus2021-08-11 | The sort of video quality you can expect from a toy drone/camera in about a 7 mph breeze. This was filmed with a UdiR/C UFO. The drone requires almost constant full stick movement input to prevent it drifting away on the breeze, and is impossible to fly smoothly.CPPM to 8 servo output decoder for any Arduino Uno/Nano/Pro Mini/etc.ceptimus2021-06-19 | This version works on most 8-bit Arduino boards (Uno / Nano / Pro Mini and so on...) It works on boards having either a 16 MHz or an 8 MHz crystal. CPPM signal connects to Arduino pin 2 Servos connect to Arduino pins: 9, 10, 11, 12, 13, A0, A1, A2 You can download the sketch here: http://ceptimus.co.uk/UnoNanoMini_CPPMdecode.zip
Discussion thread on the Mode Zero forum (join - it's free) mode-zero.uk/viewtopic.php?p=11309#p11309CPPM decoder to 8 servo outputs, using an ATmega328 chip.ceptimus2021-06-18 | The Digispark-based decoder in my previous video could only output four (or maximum five) servo channels. Here I use an ATmega328 to output a full eight servo channels. I show how to program a bare ATmega328 chip, without a crystal, to do the job so that the decoder can be kept as compact as possible. The Arduino sketch can be downloaded from: http://ceptimus.co.uk/ATmega328_8MHz_CPPMdecode.zip
There is discussion about the project on the Mode Zero forum (join - it's free) at: mode-zero.uk/viewtopic.php?f=41&t=1332CPPM to servo decoder using Digispark (ATtiny85)ceptimus2021-06-18 | How to accurately decode a CPPM (combined pulse position modulation) signal and send to (up to) five servos, using a Digispark. You can download the Arduino sketch from: http://ceptimus.co.uk/ATtiny85CPPMdecode.zip
In my comments about connecting up the programmer, I got MISO and MOSI the wrong way round. The correct connections are: MOSI P0 MISO P1 SCK P2 RST P5 VCC 5V GND GND
There's discussion about the project on the Mode Zero forum: mode-zero.uk/viewtopic.php?f=41&t=1332 You may have to register at Mode Zero, to see the discussion, but registering is free.DotMatrixClockTemperatureWeather8266ceptimus2021-06-17 | This is an update to my previous video on the dot matrix display unit: youtu.be/8O0s7X0oAr4
You can download the Arduino sketch for this video here: http://ceptimus.co.uk/DotMatrixMemoClock8266/DotMatrixClockTemperatureWeather8266.zipMultiplex Tiny-S servo with stripped gears.ceptimus2021-06-16 | Bought two together on eBay, second hand but advertised as working perfectly. One seems okay. This is the other one.F5J competition at Fish Meadow, Upton upon Severn, June 2021.ceptimus2021-06-14 | The competition was hosted at the Malvern Soaring Club's site on a hot, sunny, and low wind day. Seven rounds were flown with two slots for each round. Scroll to the end of the video to see the prize giving and results sheet.Sammys Raspberry Pisceptimus2021-05-25 | Showing some testing of Sammy's two Raspberry Pis. Probably not of much interest to anyone other than Sammy. His Pi 4B+ 8GB model seems to work fine, as far as I can see, but his Pi 3B+ has a 3.3V rail that appears to be shorted to GND, so it won't boot.clockKitceptimus2021-02-12 | Cheap Chinese clock kit demo.Arduino Mega R-2R ladder for playing sound samplesceptimus2021-01-13 | 6-bit R-2R ladder on PORTK playing sounds sampled at 15.733 kHz (which is the video horizontal frequency).Composite NTSC video out from Arduino Megaceptimus2021-01-01 | The Mega has 8K of SRAM, so enough for a screen buffer the size of the original TAITO Space Invaders (224 x 256), with 1K left over for everything else (which is what the TAITO also had, I think).
The shield looks complex, but it's just a JTAG interface for programming, and pots so I can experiment with resistor values - the actual hardware needed is just two resistors and a diode.
The Mega 2560 seems to have plenty of performance for invaders, even though it's "chasing the beam" most of the time. Without syncing the movement to one invader move per VBLANK, they were just a blur.Arduino composite video. Terminal mode now working.ceptimus2020-12-11 | Following on from previous video, I now have it working as a terminal emulator with 46 columns and 34 rows of 8x8 characters. So a pixel resolution of 368x272. I might yet be able to squeeze a few more out of it. I also have shades of grey working (not for individual pixels), but that still needs more work...Composite video out from Arduino Mega2560. 320x200 pixels.ceptimus2020-12-09 | Playing with Arduino video generation. Main project is a terminal emulator with more pixels than this (416 x 232 I think), but this was a little side experiment.Arduino Due with Atmel-ICE. Debug connection and simple blink program.ceptimus2020-11-17 | Just to show how to connect it up and get started. It's not so easy to find this kind of "obvious" newbie information out there. I guess the experts think this is so obvious that they don't need to tell us - which leaves newcomers to the SAM chips and Studio struggling. If you solder one of the little 0.127 2x5 headers to your Due, the connection is even simpler - straight ribbon cable from Atmel-ICE 'SAM' to the Due header. But if you don't have such a header to hand (like me) then this shows an alternative way of connecting.FrSky on Corona. Part 2 - uploading the sketch and serial monitoring,ceptimus2020-11-10 | In part 2, I show that the servo glitch has been fixed, then show how to configure your Arduino IDE to upload the sketch, and how to use the Arduino IDE's serial monitor and plotter to inspect and visualize the channel data. You can download the sketch here: http://ceptimus.co.uk/coronaFrSkyV8.zip
Remember! Only use a 3.3V programming USBasp or other programming device. Some of them can switch between 5V and 3.3V on the VCC line, but the signals still work at 5V when VCC is only 3.3V. These types could damage your module. Check with a scope or similar that all your programmer lines work at 3.6V maximum before connecting!FrSky protocol on Corona Moduleceptimus2020-11-09 | I got the FrSky V8 protocol to run on an old Corona CT8F transmitter module. In principle, the same module could run all the other FrSky protocols, and also Futaba SFHSS - it's just a simple matter of coding ;)The Corona module is easy to reprogram, but it only has an AtMega48, so Flash memory space is restricted, and space-efficient coding is required.
Edit: I've now fixed the bug that caused the servo glitches.FrSky V8 Arduino and CC2500 module. Now with pot fine tuning, bind, range test, etc.ceptimus2020-11-03 | Documentation here: ceptimus.co.uk/FrSkyV8Tx/FrSkyV8Tx.pdf Code here: ceptimus.co.uk/FrSkyV8Tx/FrSkyV8Tx.zip Above is the simple way using my library, derived from Pascal Langer's work. If you wish to download the original Multiprotocol source code (by Pascal Langer), you can get that here: github.com/pascallanger/DIY-Multiprotocol-TX-Module, and my config.h file for it to make it V8-only, as described in my previous video, is here: ceptimus.co.uk/FrSkyV8Tx/_Config.h.zipIkarus Piccolo at the old RC Hotelceptimus2020-10-31 | This is me flying my Piccolo (with NiMH batteries, back then!) over the old RC Hotel swimming pool, and doing a touch-and-go on the water, during a fun late night drinking session in 2001. Poor quality video because (A: 2001, B: night time, C: taken from an old VHS tape). Camera equipment and original editing by Kevin Newton, though he wasn't the cameraman for this sequence. I've had to remove the audio because potential YouTube copyright strike - Kevin had put "Roam" by the B52s, as the backing track, and you could also hear the original drunken revelry audio with shouts of "Come on, Martin! You can do it!" Fun times! I'm uploading it now because of a forum post concerning renewed interest in the Piccolo.FrSky V8 transmitter module using Arduino and CC2500ceptimus2020-10-24 | It's just Pascal's MultiProtocol code but with _Config.h edited to remove everything except FrSky V8 mode.Max7219 dot matrix display: clock, calendar, and memo board.ceptimus2020-10-17 | I used a Wemos D1, to drive the display. This is an ESP 8266 chip on an Arduino Uno form-factor board. I wrote the code using Arduino IDE and tested it using a Nano, but then swapped to using the 8266 to take advantage of the Web connectivity. You could also use an ESP 32 - the code runs on that too - but you need a power supply that can deliver about an amp - either on 3.3V or 5V - if you want to light up lots of the LEDs at full brightness: most of the ESP 32 offerings don't have that sort of power supply built in. The Wemos D1 boards are also dirt cheap. Total parts cost for the contraption is about thirty dollars on Ali Express, as of October 2020.
...and the STL files here: ceptimus.co.uk/DotMatrixMemoClock8266/stlFiles.zipMark Christy, test flying my gyro.ceptimus2020-08-09 | Here's Mark (expert heli pilot and British team member) test flying my gyro in his dad's old Voyager-E in rate mode. Mark wasn't happy with the 'heading hold mode' and didn't want to risk flying with that - but he said the rate mode is okay and doesn't need altering! See http://mode-zero.uk/viewtopic.php?f=42&t=1018 for details on how to make the gyro.Trex 450 test stand (part 2)ceptimus2020-07-31 | After making some bug fixes and enhancements to the gyro code - particularly for the heading hold mode - here is the modified gyro performing on the test stand.