Uploaded May 2020 | Updated November 2026, 1 day ago
Welcome Back,
Where do I start……
I put out a request on my instagram page (link below), to see what you guys wanted me to turn for this week's video.
instagram.com/mgmakes
To say it didn't quite turn out as well as i had expected is an understatement. I encountered numerous issues
Mounting to the chuck, As the log was round (obviously) I needed to create a flat spot to allow even pressure from the chuck to support the piece. I didn't have a forstner bit large enough, so I drew around the chuck and nibbled away with a chisel to create a surface large enough.
Finishing. Where possible and its safe to do so, finish the outside first. I did that to start with, but because I didn't read the instructions on the tin, i applied it too thick and it looked rubbish, so with the piece reversed in the chuck i took away the old finish and then had to sand it back up to 400 grit, which is not the easiest thing to do as the wings were flexing (no Support) - hence the particular bad result.
Moisture. When I started to turn this piece, it felt dry enough, but as the turning progressed i realised that it was not. So if this happens to you and your not an idiot from Youtube, trying to create content, stop when the turning has finished, pop it into a bag with its shavings and wait for it to dry out and then finish it. Because if like me you opt to carry on, then sanding is a nightmare as all you are doing is pushing the fibres to the side, not actually sanding. Applying any finish on damp wood is not recommended as the potential for a reaction or poor adhesion is greatly increased.
I hope that you find my rambling of some use
Thank you for the support of my channel sponsor Dremel Uk - Link below
dremeleurope.com/gb/en
To create this piece I used
Dremel Fortiflex
dremeleurope.com/gb/en/dremel%C2%AEfortiflex-6136-ocs-c
High Speed Cutter 7.2mm (134)
dremeleurope.com/gb/en/highspeedcutter7-2mm-97-ocs-p
I am really happy to announce that Chestnut Products are supporting me and helping me up my Finishing game, all tips and tricks that I learn will be passed on to you guys, cause what else am i doing this for.
chestnutproducts.co.uk
These guys are still shipping out orders, so follow the link and treat yourself whilst we are still in lockdown.
So, stay safe and happy turning
Take pride in what you do and don't fear failure, aim to be the best you can be and enjoy what you do.
I have recently joined Pateron - so if you would like to help fund future videos then please pop on over to my Patreon Page and support me - with as little or as much as you would like to - no pressure.
patreon.com/user?alert=2
As always, I will share my trials and tribulations documenting my journey. As I believe that it is important to grow and learn from your mistakes.
If you would like to Support my work, then please consider leaving me a “tip” in my paypal account - all donations will go towards future projects
paypal.me/mgmakes
Thanks for watching and stay safe.
Yes I know I will not be doing some things correctly, I will be making mistakes, but i will will try to work safe and learn from my mistakes and improve on my techniques as we go along.
I hope you enjoy the video.
Please Follow me on,
Instagram
instagram.com/mgmakes
Facebook
facebook.com/mg.makes.73
A Proud Member of
Small Workshop YouTube Makers Facebook Group
facebook.com/groups/SmallWorkshopYouTubeMakers
Makers Media Network
facebook.com/groups/MakersMediaNetwork
Welcome Back,
Where do I start……
I put out a request on my instagram page (link below), to see what you guys wanted me to turn for this week's video.
instagram.com/mgmakes
To say it didn't quite turn out as well as i had expected is an understatement. I encountered numerous issues
Mounting to the chuck, As the log was round (obviously) I needed to create a flat spot to allow even pressure from the chuck to support the piece. I didn't have a forstner bit large enough, so I drew around the chuck and nibbled away with a chisel to create a surface large enough.
Finishing. Where possible and its safe to do so, finish the outside first. I did that to start with, but because I didn't read the instructions on the tin, i applied it too thick and it looked rubbish, so with the piece reversed in the chuck i took away the old finish and then had to sand it back up to 400 grit, which is not the easiest thing to do as the wings were flexing (no Support) - hence the particular bad result.
Moisture. When I started to turn this piece, it felt dry enough, but as the turning progressed i realised that it was not. So if this happens to you and your not an idiot from Youtube, trying to create content, stop when the turning has finished, pop it into a bag with its shavings and wait for it to dry out and then finish it. Because if like me you opt to carry on, then sanding is a nightmare as all you are doing is pushing the fibres to the side, not actually sanding. Applying any finish on damp wood is not recommended as the potential for a reaction or poor adhesion is greatly increased.
I hope that you find my rambling of some use
Thank you for the support of my channel sponsor Dremel Uk - Link below
dremeleurope.com/gb/en
To create this piece I used
Dremel Fortiflex
dremeleurope.com/gb/en/dremel%C2%AEfortiflex-6136-ocs-c
High Speed Cutter 7.2mm (134)
dremeleurope.com/gb/en/highspeedcutter7-2mm-97-ocs-p
I am really happy to announce that Chestnut Products are supporting me and helping me up my Finishing game, all tips and tricks that I learn will be passed on to you guys, cause what else am i doing this for.
chestnutproducts.co.uk
These guys are still shipping out orders, so follow the link and treat yourself whilst we are still in lockdown.
So, stay safe and happy turning
Take pride in what you do and don't fear failure, aim to be the best you can be and enjoy what you do.
I have recently joined Pateron - so if you would like to help fund future videos then please pop on over to my Patreon Page and support me - with as little or as much as you would like to - no pressure.
patreon.com/user?alert=2
As always, I will share my trials and tribulations documenting my journey. As I believe that it is important to grow and learn from your mistakes.
If you would like to Support my work, then please consider leaving me a “tip” in my paypal account - all donations will go towards future projects
paypal.me/mgmakes
Thanks for watching and stay safe.
Yes I know I will not be doing some things correctly, I will be making mistakes, but i will will try to work safe and learn from my mistakes and improve on my techniques as we go along.
I hope you enjoy the video.
Please Follow me on,
instagram.com/mgmakes
facebook.com/mg.makes.73
A Proud Member of
Small Workshop YouTube Makers Facebook Group
facebook.com/groups/SmallWorkshopYouTubeMakers
Makers Media Network
facebook.com/groups/MakersMediaNetwork










