Uploaded December 2018 | Updated November 2026, 2 days ago
This is project for Jim aka Jimbolio, who runs around in the desert in "The Precious". 10 years ago, in Los Angeles, he picked up his FJ Cruiser with 23 Miles on it. Why Los Angeles? We'll it turns out that finding a MT6 (Manual Trans) with the Off-road Package, and in Sun Fusion Yellow was harder than it seemed.
Fast forward 10 years of off-road use and abuse and the restoration project is in full swing.
Today's pen turning project is a Penn State Gearshift Pen Kit (#PKGEARCH). For the Pen Blank, I used a yellow acrylic blank to match Jim's FJ.
My website:
wolfridgewoodworking.com
Please subscribe to my channel: youtube.com/channel/UCUVMh5tubVADcaNujTMVdGA
Pen making is one of the easiest projects to start with when you are beginning woodturning. All you need to get started woodturning a pen is a lathe, woodturning tools, a pen kit, a pen blank, sandpaper, some sort of finish, and a willingness to learn!
The basic steps to turning a pen is:
1. Cut the pen blank to fit the brass tubes.
2. Drill the proper sized hole to fit the brass tubes and glue in the tubes using CA glue.
3. Make the ends of the blank flat and square.
4. Turn the pen blank down to the correct bushings.
5. If a wood blank was used, sand to 400 grit or if acrylic, skip to step 7.
6. Apply a finish like CA glue or a friction polish.
7. Sand using micro mesh pads from 1500 to 12,000 grit.
8. Apply one or more coats of a plastic polish.
Please leave a comment if there are any questions you have or if you feel like a missed explaining a step.
Tools that I used in this project
Jet 1221VS Lathe:
amzn.to/2OdLhCB
Easy Wood Tools Carbide Tools:
amzn.to/2N0FTy5
Pen Kit:
bit.ly/2rJnjSZ
Pen Blank:
bit.ly/2R4Fpgp
Bushing Set:
bit.ly/2yrugfd
HUT Ultra Gloss Plastic Polish
amzn.to/2QxvuMV
Micromesh:
amzn.to/2DHFIIC
Camera gear used to record project
Canon M50 Mirrorless Camera:
amzn.to/2ORcEQ5
Sigma 17-50mm f/2.8 Lens:
amzn.to/2QcB7Qj
This is project for Jim aka Jimbolio, who runs around in the desert in "The Precious". 10 years ago, in Los Angeles, he picked up his FJ Cruiser with 23 Miles on it. Why Los Angeles? We'll it turns out that finding a MT6 (Manual Trans) with the Off-road Package, and in Sun Fusion Yellow was harder than it seemed.
Fast forward 10 years of off-road use and abuse and the restoration project is in full swing.
Today's pen turning project is a Penn State Gearshift Pen Kit (#PKGEARCH). For the Pen Blank, I used a yellow acrylic blank to match Jim's FJ.
My website:
wolfridgewoodworking.com
Please subscribe to my channel: youtube.com/channel/UCUVMh5tubVADcaNujTMVdGA
Pen making is one of the easiest projects to start with when you are beginning woodturning. All you need to get started woodturning a pen is a lathe, woodturning tools, a pen kit, a pen blank, sandpaper, some sort of finish, and a willingness to learn!
The basic steps to turning a pen is:
1. Cut the pen blank to fit the brass tubes.
2. Drill the proper sized hole to fit the brass tubes and glue in the tubes using CA glue.
3. Make the ends of the blank flat and square.
4. Turn the pen blank down to the correct bushings.
5. If a wood blank was used, sand to 400 grit or if acrylic, skip to step 7.
6. Apply a finish like CA glue or a friction polish.
7. Sand using micro mesh pads from 1500 to 12,000 grit.
8. Apply one or more coats of a plastic polish.
Please leave a comment if there are any questions you have or if you feel like a missed explaining a step.
Tools that I used in this project
Jet 1221VS Lathe:
amzn.to/2OdLhCB
Easy Wood Tools Carbide Tools:
amzn.to/2N0FTy5
Pen Kit:
bit.ly/2rJnjSZ
Pen Blank:
bit.ly/2R4Fpgp
Bushing Set:
bit.ly/2yrugfd
HUT Ultra Gloss Plastic Polish
amzn.to/2QxvuMV
Micromesh:
amzn.to/2DHFIIC
Camera gear used to record project
Canon M50 Mirrorless Camera:
amzn.to/2ORcEQ5
Sigma 17-50mm f/2.8 Lens:
amzn.to/2QcB7Qj










