Uploaded October 2026 | Updated November 2026, 20 hours ago
Vlog 10/27/2026, including the following activities:
-Put away the Halispechts Lighting XA2-852/5AB 52" Ornate Ceiling Fan.
-Retrieve the Fall/Thanksgiving decorations.
-Retrieving a free Casablanca ceiling fan from the Facebook Marketplace.
-Changing the bag in the ProTeam ProForce 1500XP vacuum.
-Cleaning the couch in the living room.
-Vacuuming the living room (ProTeam ProForce 1500XP vacuum).
-Watering a fern.
Vlog 10/27/2026, including the following activities:
-Put away the Halispechts Lighting XA2-852/5AB 52" Ornate Ceiling Fan.
-Retrieve the Fall/Thanksgiving decorations.
-Retrieving a free Casablanca ceiling fan from the Facebook Marketplace.
-Changing the bag in the ProTeam ProForce 1500XP vacuum.
-Cleaning the couch in the living room.
-Vacuuming the living room (ProTeam ProForce 1500XP vacuum).
-Watering a fern.


![Lasko H20301 20 Max Performance High Velocity Fan Review
My review of the Lasko 20 Max Performance High Velocity Fan model H20301. Note that there are numerous versions of this fan under different model numbers; the commentary here is applicable to model H20301 and may or may not be relevant to the others.
I have mixed feelings about a lot of Lasko products, but I generally consider them to be a good value. The price is low enough and the performance is decent enough to offset some of the QC and manufacturing tolerance issues present in many Lasko builds.
This unit is very average to me. It moves a decent amount of air, but isnt particularly strong. Its not obnoxiously loud, but it certainly isnt quiet. The physical form factor is decent, it sits sturdy on the base, isnt too heavy, and is easy to take apart for cleaning. The motor doesnt have oil ports like it should, but its easy enough to disassemble to refill the oil wicks. I like the controls on the front of the fan as opposed to the back near the motor. Surprisingly, the blade is in reasonable balance. This is rare for Lasko, I assume this is a fluke and the majority are totally out of balance.
Where the unit really fails is speed selection. This has 3 speeds, but each of the speeds hardly has any difference. Theres less than a 300 CFM difference between low and high, and only about 1 MPH difference between each speed. Consequently theres also little noise difference; its more so just a change in pitch than loudness.
If this had a good selection of speeds to the point where Low is about half of high, this would be quiet and tame enough for use in a bedroom, kitchen, small living room, or other similar living spaces. As it is without speeds, I really wouldnt want to use it much of anywhere beyond the garage. The low speed is tolerable in the large living room during the day when the windows are open and other background noise is present, but even at night when its quiet, its a bit too much in there. This can be solved by running the fan on a variac to create whatever speeds youd like, but one shouldnt have to... Of course theres the argument that this is a high velocity fan and performs accordingly, but it still would have been nice to be able to slow it down like the old Patton units from the 90s. It would make the fan much more versatile.
The blade, as with many of the other blades Lasko currently uses, is not very good from an aerodynamics perspective. The tips of the blades dont move any air; theres only about 17 of air moving surface despite the blade being almost 20 across. The blade itself isnt quite 20, and the whole width of the fan is far more than 20, so I have no idea where the 20 even comes from. There are far superior blade designs available that would move more air with less noise.
In conclusion, I think this is an OK fan, but it shouldnt be as expensive as it is. Theres a surprisingly wide range of high velocity fans currently available on the market of all product tiers, ranging from about $50 on the low end to upwards of $200 on the high end. Aside from potential longevity (which only time will tell), Im not seeing what puts this ahead of the $50 models and find it hard to consider this one to be a good value. I tend to think, like a lot of other Lasko products, that this sells simply because it exists and people are aware of the brand, not because its objectively better than other models or because its a particularly good value.
The specifications captured during the video are as follows, represented respectively [Airflow (CFM) / Efficiency (CFM/watt) / Power (watts) / Current (amps) / Loudness (dBA) / Wind speed (MPH) at 0 / 5 / 10]:
Low: [1,918 / 19 / 100 / 0.87 / 61 / 15.5 / 8 / 5].
Medium: [2,095 / 19 / 109 / 0.96 / 62 / 16 / 9 / 5].
High: [2,184 / 17 / 126 / 1.09 / 64 / 17 / 9 / 6]. Lasko H20301 20 Max Performance High Velocity Fan Review](https://i.ytimg.com/vi/QRAtf4oNd68/mqdefault.jpg)





![Lakewood 225RG and Lasko A20107 Blade Swap
Blade swap between the Lakewood 225RG and the Lasko A20107 fan.
The A20107 motor is not anywhere near powerful enough to handle the Lakewood blade. The performance, while very limited, was very similar to that of the Kool Operator. Very quiet, gentle breeze that carried a good distance. Air flow and efficiency decreased on all speeds, though not by as significant of a margin as it felt like according to the numbers.
The Lakewood 225RG made the Lasko blade ssssspiiiiIIIiIiIII!!!Innn!! real fast, Im actually a bit surprised it didnt explode. On low and medium, the performance was improved considerably, despite the decrease in the surface area moving air. On high, the trend reversed, likely because the blade started folding under the resistance of the speed.
Very surprisingly, between these two, Id have to say the Lasko blade seems to be a better design aerodynamically than the Lakewood.
The specifications measured during the video are as follows, represented as [Power (watts) / Current (amps) / Power Factor / Air Flow Volume (CFM) / Efficiency (CFM/watt) / Wind Velocity Up Close (MPH) / Wind Velocity 5 Away (MPH)].
Lasko A20107, default blade:
Low: [42 / 0.42 / 0.82 / 732 / 17.4 / 7 / 5].
Medium: [49 / 0.47 / 0.87 / 944 / 19.3 / 8.7 / 6].
High: [58 / 0.51 / 0.93 / 1,062 / 18.3 / 10 / 7].
Lasko A20107, Lakewood blade:
Low: [50 / 0.43 / 0.94 / 690 / 13.8 / 6 / 3.5].
Medium: [56 / 0.48 / 0.96 / 817 / 14.6 / 7.3 / 4.5].
High: [63 / 0.53 / 0.99 / 920 / 14.6 / 8 / 5].
Lakewood 225RG, default blade:
Low: [81 / 0.69 / 0.97 / 1,237 / 15.3 / 8.5 / 4.5].
Medium: [95 / 0.81 / 0.98 / 1,539 / 16.2 / 10 / 5].
High: [115 / 1.04 / 0.92 / 1,905 / 16.6 / 12.7 / 6].
Lakewood 225RG, Lasko blade:
Low: [74 / 0.62 / 0.99 / 1,432 / 19.4 / 11.8 / 8.5].
Medium: [87 / 0.73 / 0.99 / 1,680 / 19.3 / 14 / 9].
High: [98 / 0.94 / 0.86 / 1,790 / 18.3 / 14.7 / 9]. Lakewood 225RG and Lasko A20107 Blade Swap](https://i.ytimg.com/vi/T050lbrH038/mqdefault.jpg)

![Blade Swap | Lasko 3733 Box Fan and Lakewood 225RG Rain Guard Box Fan
Blade swap of the Lasko 3733 box fan and the Lakewood 225RG Rain Guard box fan. Very interesting results from this one.
The Lakewood motor is considerably more powerful, a more fair comparison would be the Lakewood 225RG up against a WeatherShield, Premium, Power Plus, etc.
This test suggests the Lakewood blade is not as good of a design as I was expecting. It does have a wider throw of air giving it a significant advantage in the volume of air moved, but it also appears to have considerably more drag than the Lasko blade.
The Lasko blade actually came out more efficient when put on the Lakewood on speeds low and medium, while the Lasko 3733s performance suffered considerably with the Lakewood blade. The trend of the Lasko blade beting better on the Lakewood did reverse at high speed, and I suspect this is because the blade starts to fold under the air resistance. This is where the brace blade comes into play the brace maintains the pitch of the blades at all speeds.
The Lakewood blade did not throw as wide of an air path when on the Lasko 3733, which speaks volumes about the guard design used on those fans. Its very restrictive. The design of the Lakewoods guard is much more aerodynamically correct. Lasko knows this and has made other models with circular guards for decades. It is absolutely baffling to me that Lasko still sells fans with this poor guard design, knowing that it reduces the fans performance for absolutely no reason.
The specifications recorded during the video are as follows, represented as [Power (watts) / Air Flow (CFM) / Efficiency (CFM/watt) / Air Velocity Close (MPH) / Air Velocity at 5 Away (MPH)].
Lasko 3733, default blade:
Low: 62 / 850 / 13.7 / 8 / 4.6.
Medium: 74 / 1.015 / 13.7 / 10 / 6.
High: 90 / 1,274 / 14.6 / 11.4 / 7.
Lasko 3733, Lakewood RainGuard blade:
Low: 56 / 684 / 12.2 / 6.4 / 3.
Medium: 69 / 825 / 12 / 7.6 / 4.4.
High: 90 / 944 / 10.5 / 9 / 5.
Lakewood RainGuard, default blade:
Low: 81 / 1,237 / 15.3 / 8.5 / 4.5.
Medium: 95 / 1,539 / 10 / 5.
High: 115 / 1,905 / 16.6 / 12.7 / 6.
Lakewood RainGuard, Lasko 3733 blade:
Low: 68 / 1,404 / 20.6 / 11 / 5.
Medium: 87 / 1,625 / 18.7 / 13 / 7.
High: 100 / 1,817 / 18.2 / 14.7 / 8. Blade Swap | Lasko 3733 Box Fan and Lakewood 225RG Rain Guard Box Fan](https://i.ytimg.com/vi/TEjq23K8WDM/mqdefault.jpg)