Uploaded May 2020 | Updated November 2026, 2 days ago
We’ve been wanting to make our own push stick for a little while and wanted to come up with a simple way to make it adjustable. We based our design partially on our favourite style of push stick (from John Heisz) and added a ledge on the back where a dowel can be held. This is just friction fit in place and can be easily adjusted with a tap on the bench. We also made the handle a little more comfortable to hold and added another notch on the front for additional function.
There is a link to the free template below if you want to make one of your own. We suggest using 18mm plywood as this gives enough thickness for the 10mm dowel. Try to ensure the dowel is a tight fit. Ideally it should be difficult to move by hand.
We used HDPE in this video and this works well because HDPE is a super rigid material with no grain, therefore this makes it very safe as a push stick. The bright colours also make it easy to spot! Ideally, you want to try and avoid natural wood for push sticks in case they were to fail by splitting along the grain. Plywood (or HDPE!) is a great material as it is strong in multiple directions. We used all of the offcuts from the HDPE Stool and HDPE Coffee Cup Carrier videos. If you haven’t seen them then be sure to check them out. The sanding is not at all necessary, especially for a push stick, however uncovering that amazing marbling is very addictive and we like the things we make to look as good as they can.
We hope that you found this useful! If you do make your own, be sure to send or tag us in your Instagram pictures! (@brothersmake)
#BrothersMake #HDPE #PreciousPlastic #HDPERecycling #RecycledPlastic #RecycledPlasticBottles #PlasticRecycling #PushStick
TEMPLATE LINK if you want to make your own!
https://i.postimg.cc/xCQB4tT1/Push-Stick-Template.jpg
Consider supporting us on PATREON:
patreon.com/brothersmake
Follow us on INSTAGRAM:
instagram.com/brothersmake
Link to our MERCH store:
teespring.com/en-GB/stores/brothersmake
STARBOND SUPERGLUE 10% off using BROTHERSMAKE10 or click the link below:
starbond.com/?rfsn=3704868.592ffa8
Check out our PLAYLIST with all of our HDPE videos:
bit.ly/2SARcTo
MUSIC:
'Sunrise Drive' - South London HiFi
'Sam Stoopid' - Mikos Da Gawd
We’ve been wanting to make our own push stick for a little while and wanted to come up with a simple way to make it adjustable. We based our design partially on our favourite style of push stick (from John Heisz) and added a ledge on the back where a dowel can be held. This is just friction fit in place and can be easily adjusted with a tap on the bench. We also made the handle a little more comfortable to hold and added another notch on the front for additional function.
There is a link to the free template below if you want to make one of your own. We suggest using 18mm plywood as this gives enough thickness for the 10mm dowel. Try to ensure the dowel is a tight fit. Ideally it should be difficult to move by hand.
We used HDPE in this video and this works well because HDPE is a super rigid material with no grain, therefore this makes it very safe as a push stick. The bright colours also make it easy to spot! Ideally, you want to try and avoid natural wood for push sticks in case they were to fail by splitting along the grain. Plywood (or HDPE!) is a great material as it is strong in multiple directions. We used all of the offcuts from the HDPE Stool and HDPE Coffee Cup Carrier videos. If you haven’t seen them then be sure to check them out. The sanding is not at all necessary, especially for a push stick, however uncovering that amazing marbling is very addictive and we like the things we make to look as good as they can.
We hope that you found this useful! If you do make your own, be sure to send or tag us in your Instagram pictures! (@brothersmake)
#BrothersMake #HDPE #PreciousPlastic #HDPERecycling #RecycledPlastic #RecycledPlasticBottles #PlasticRecycling #PushStick
TEMPLATE LINK if you want to make your own!
https://i.postimg.cc/xCQB4tT1/Push-Stick-Template.jpg
Consider supporting us on PATREON:
patreon.com/brothersmake
Follow us on INSTAGRAM:
instagram.com/brothersmake
Link to our MERCH store:
teespring.com/en-GB/stores/brothersmake
STARBOND SUPERGLUE 10% off using BROTHERSMAKE10 or click the link below:
starbond.com/?rfsn=3704868.592ffa8
Check out our PLAYLIST with all of our HDPE videos:
bit.ly/2SARcTo
MUSIC:
'Sunrise Drive' - South London HiFi
'Sam Stoopid' - Mikos Da Gawd

![Melting Milk Bottle Tops for Breakfast
Remember the HDPE cutting board we made? (https://bit.ly/2FxcnlT) Well, we took the leftover plastic from that sheet and tried our hand at carving some spoons from it! We havent done a huge amount of carving in the past, but enough to be able to tell that this stuff is a LOT harder to carve than wood - which we were very surprised by! We really like the faceted texture on these spoons - what do you guys think?
If you are concerned about the food safety-ness off recycled HDPE then we have put our thoughts below. We would like to make one disclaimer here, which is that we do not advise any recycled HDPE projects be brought into contact with heat. The low melting temperature of the plastic means that it warps and deforms easily. These spoons will be for cold use only.. sugar, cereal, gazpacho etc!
In terms of HDPE and food safety... we have researched this fairly extensively and we are confident that our process is clean enough to produce food-grade HDPE: HDPE is a food-grade plastic, hence why it is used for milk bottles and packaging for other edible goods. This is most likely sourced from raw (or virgin) polymer which means that it has not gone through a recycling process. This issue with recycling plastic is that there are multiple avenues for the plastic to become contaminated. The 3 main ones being;
1) Remains from the previous content it was holding
2) Labels/residue left on the plastic itself
3) Potential burning of the plastic, which introduces toxins (both as fumes and within the resulting plastic product itself)
We are very meticulous when it comes to the cleaning of our plastic. All plastic that we receive is hand-sorted to ensure it is indeed HDPE and that there are no non-plastic contaminants left on the plastic. We run the plastic through at least 3 sorting and cleaning cycles before we ever introduce it to heat. This covers (1) and (2). HDPEs burning point is anything over 180 degrees Celcius. We have had enough experience with melting this plastic to know when it has got too hot. We keep our over/grill at around 140-160 degrees, which never introduces any fumes or burning to any of the plastic. This covers (3).
The US Food and Drug Administration has recently (March 2020) approved recycled HDPE to be used for food and drink packaging providing the feedstock is food-grade and contaminant concentrations were below its “threshold of regulatory concern” (0.5 parts per billion or less in the food). [https://bit.ly/33F4Ueq]
If you are still concerned about the use of recycled HDPE for use with food then feel free to not use it yourself! We have done the research and have decided that we think it is safe based on our specific process.
This video is not telling you that you have to do this, rather it is showing you what is possible! If you enjoyed the video or learnt something new, please consider subscribing. Thanks!
#BrothersMake #HDPE #PreciousPlastic #HDPERecycling #RecycledPlastic #RecycledPlasticBottles #PlasticRecycling #SpoonCarving
FAQ:
➡️ We dont currently sell any of our product but we are looking to in the future - keep an eye on our instagram!
➡️ HDPE doesnt give off any smells or toxic fumes when melted providing it is kept below the burning point of 180 degrees C (we stick to 150-160 C).
➡️ We dont buy any of our plastic. It all comes from collection and donations. We have a video all about it: https://bit.ly/2RsbhKA
➡️ Our workshop is powered 100% by renewable energy. We don’t use any energy from fossil fuels whatsoever.
➡️ The black sheets we use on the grill are called Teflon Baking Mats: https://amzn.to/33sIKdx
➡️ The gloves we use are called Silicomne Oven Mits https://amzn.to/2ZxwUh9
Consider supporting us on PATREON:
https://www.patreon.com/brothersmake/
Follow us on INSTAGRAM:
https://www.instagram.com/brothersmake/
Link to our MERCH store:
https://teespring.com/en-GB/stores/brothers-make-apparel
STARBOND SUPERGLUE 10% off using BROTHERSMAKE10 or click the link below:
https://www.starbond.com/?rfsn=3704868.592ffa8
Check out our PLAYLIST with all of our HDPE videos:
https://bit.ly/2SARcTo
Music by Epidemic Sound (http://www.epidemicsound.com) Melting Milk Bottle Tops for Breakfast](https://i.ytimg.com/vi/9b2hWyhvO20/mqdefault.jpg)








