Trimming Tricky Trinket Boxes #pottery @floriangadsby

Uploaded August 2025 | Updated September 2026, 2 weeks ago

If you’d like to watch both the throwing and the trimming of these trinket boxes or store jars, you can find a link to the fully narrated video via on YouTube via the Linktree in my profile’s biography.

These are deceptive objects. Simple, yes, yet trimmed to an astonishing level, my fault really for accidentally throwing the lids far larger than need be… I’m sure I’m not the only person that’s measured the opening of their jars only to then knock it larger, or smaller, without realising.

Thankfully, my general approach when making lidded ware is to throw the lids themselves thicker than need be, not the overhang itself, that was too much on these, but the vertical locating flange, for instance, is a segment of the pot I always throw more substantially, this way it can be trimmed back to fit the vessel underneath it no matter what. I’ll be trimming the underside of my lids regardless, so this fraction of additional material acts like a safety net of sorts.

Yet, that’s no excuse for the portion of the lid that’s overhanging to this degree, the next time I make these I’ll spend a few extra moments measuring.

These are useful pots though, the wider opening means I can easily reach inside to fish out salt or spices, or it can be used for trinkets, rings and the like, in fact, you can put anything inside, it’s not my job to tell you what to do with these.

#pottery #satisfying #clay #stoneware #jar #ceramics #maker

$Trimming Tricky Trinket Boxes #pottery If you’d like to watch both the throwing and the trimming of these trinket boxes or store jars, you can find a link to the fully narrated video via on YouTube via the Linktree in my profile’s biography. These are deceptive objects. Simple, yes, yet trimmed to an astonishing level, my fault really for accidentally throwing the lids far larger than need be… I’m sure I’m not the only person that’s measured the opening of their jars only to then knock it larger, or smaller, without realising. Thankfully, my general approach when making lidded ware is to throw the lids themselves thicker than need be, not the overhang itself, that was too much on these, but the vertical locating flange, for instance, is a segment of the pot I always throw more substantially, this way it can be trimmed back to fit the vessel underneath it no matter what. I’ll be trimming the underside of my lids regardless, so this fraction of additional material acts like a safety net of sorts. Yet, that’s no excuse for the portion of the lid that’s overhanging to this degree, the next time I make these I’ll spend a few extra moments measuring. These are useful pots though, the wider opening means I can easily reach inside to fish out salt or spices, or it can be used for trinkets, rings and the like, in fact, you can put anything inside, it’s not my job to tell you what to do with these. #pottery #satisfying #clay #stoneware #jar #ceramics #maker$

How to Collar in Clay — A Beginners Guide

How I Trim Pottery with More Control (Turning a Bottle using a Chuck)

$Throwing 1000’s of Mugs When I’m making mugs, I like to make lots at once. Generally, this means spending a week or two producing 100-200 pieces, whilst juggling a number of other tasks, mainly, as I feel as if by working on so many at once, they end up being more consistent and I become faster as I’m repeating the creation process so many times in a row. It sort of feels like practice and I can always sense a difference in my ability at the beginning of a mug making session, versus how naturally they are formed and handled towards the end, after I’ve warmed up, essentially. I throw mine from 300 grams of clay, (plus or minus 10 for speedier weighing out), to 11 cm tall by 8.5 cm wide, give or take a few millimetres. I don’t mind if one is a smidge below my throwing gauge’s pointer as I pull up the walls, or if one is fractionally too wide, as these minute discrepancies will barely be noticeable once the pot has been trimmed, handled, glazed and fired. What I do care about though are the proportions and the slightly tapering shape. It can hard to see, but these pots are marginally wider at the base and then they slope inwards ever so slightly as they reach upwards. It’s subtle but it makes a big difference and so, if I notice that a mug is too straight, or that it flared out towards the top, it’ll be instantly destroyed if I can’t fix that during the throwing process itself. It’s good to be brutal, you can never be too precious, essentially with vessels as simple as these are. Lifting off these thinly walled pots in the perhaps the trickiest part. There’s a bit of a knack to it, (that’s better explained in my YouTube video that specifically covers this step), but it means I can heap more onto each ware board, which means I don’t have to use batts and for a pot like this that means I end up saving a bit more space in the studio. Space, as you quickly realise, is perhaps one of the most importance things about a potter’s studio. It’s a bottleneck you’ll often run into and you need more space during the production stage, as pots need room to dry and components eat up shelves before they’re assembled. 100 more to go… #mugs #handmade #craft #wheelthrownpottery #pottery$