Uploaded September 2025 | Updated September 2026, 1 week ago
What a week. Trailer got broken into in Indy—about $3,500 in Milwaukee tools and other gear GONE. THey messed up the door pretty bad, but The scooter survived (lol), the trailer survived, and we decided to lean into it:
🧰 This weekend only (Sept 13–14, 2025): we’re putting a tool in EVERY shipped order + 25× entries toward the S13 giveaway.
👉 Shop / Enter (25× entries): motionautotv.com
(Physical orders only; digital downloads excluded.)
In this episode: parts run at Harbor Freight + Home Depot, “tools-in-orders” haul, Type-X wing install, full Wiring Specialties engine & chassis harness, fuel pump hardwire, intercooler/radiator fitment, top-mount GTX3071R clearance fixes, custom downpipe & IC piping, battery relocation, and the SR20 first start.
Build bits you’ll see
Wiring Specialties S13 SR harness + fan & fuel-pump relay kits
DW400 pump + regulator, hardwire kit from wiring specialties
GREDDY intercooler & cat-back, Koyo triple-pass radiator, electric fans
GTX3071R top-mount, Cerakote’d cast manifold
Type-X wing, zinc hardware refresh
🙏 Thanks: Eric, Sean, Wiring Specialties crew, and everyone supporting the build.
00:00 What the [ __ ] — trailer break-in
01:05 Tools gone, scooter saved, damage walk-around
03:02 Weekend plan: Tools in Every Order (25× entries)
04:20 Harbor Freight + Home Depot haul (what’s going into orders)
08:10 Back at shop: Type-X wing install & paint correction
11:05 Old spaghetti harness vs Wiring Specialties clean setup
14:20 Fuel pump hardwire kit + tank refresh
17:10 Regulator/filter layout & E85 crust autopsy
19:45 Radiator + fan mockup (Koyo triple-pass)
22:30 Intercooler in without pulling the bumper (win)
24:10 Turbo/master cylinder clearance fix (banjo + spacer trick)
27:15 Battery relocation w/ breaker (safety note)
30:00 CAS/timing check + first crank for oil pressure
32:10 Low fuel pressure mystery → quick diagnosis
34:40 Fix → instant 100 psi test / proper base pressure
36:00 Cutting & clocking the IC pipes (speed density bung)
39:15 Custom downpipe (pie cuts, v-band, O2 bung)
42:10 Final wiring tidy + fan control
44:20 First Start! (exhaust note)
46:10 What’s next + weekend tool promo reminder
What a week. Trailer got broken into in Indy—about $3,500 in Milwaukee tools and other gear GONE. THey messed up the door pretty bad, but The scooter survived (lol), the trailer survived, and we decided to lean into it:
🧰 This weekend only (Sept 13–14, 2025): we’re putting a tool in EVERY shipped order + 25× entries toward the S13 giveaway.
👉 Shop / Enter (25× entries): motionautotv.com
(Physical orders only; digital downloads excluded.)
In this episode: parts run at Harbor Freight + Home Depot, “tools-in-orders” haul, Type-X wing install, full Wiring Specialties engine & chassis harness, fuel pump hardwire, intercooler/radiator fitment, top-mount GTX3071R clearance fixes, custom downpipe & IC piping, battery relocation, and the SR20 first start.
Build bits you’ll see
Wiring Specialties S13 SR harness + fan & fuel-pump relay kits
DW400 pump + regulator, hardwire kit from wiring specialties
GREDDY intercooler & cat-back, Koyo triple-pass radiator, electric fans
GTX3071R top-mount, Cerakote’d cast manifold
Type-X wing, zinc hardware refresh
🙏 Thanks: Eric, Sean, Wiring Specialties crew, and everyone supporting the build.
00:00 What the [ __ ] — trailer break-in
01:05 Tools gone, scooter saved, damage walk-around
03:02 Weekend plan: Tools in Every Order (25× entries)
04:20 Harbor Freight + Home Depot haul (what’s going into orders)
08:10 Back at shop: Type-X wing install & paint correction
11:05 Old spaghetti harness vs Wiring Specialties clean setup
14:20 Fuel pump hardwire kit + tank refresh
17:10 Regulator/filter layout & E85 crust autopsy
19:45 Radiator + fan mockup (Koyo triple-pass)
22:30 Intercooler in without pulling the bumper (win)
24:10 Turbo/master cylinder clearance fix (banjo + spacer trick)
27:15 Battery relocation w/ breaker (safety note)
30:00 CAS/timing check + first crank for oil pressure
32:10 Low fuel pressure mystery → quick diagnosis
34:40 Fix → instant 100 psi test / proper base pressure
36:00 Cutting & clocking the IC pipes (speed density bung)
39:15 Custom downpipe (pie cuts, v-band, O2 bung)
42:10 Final wiring tidy + fan control
44:20 First Start! (exhaust note)
46:10 What’s next + weekend tool promo reminder
