Uploaded July 2021 | Updated November 2026, 13 hours ago
Looking for a circle cutting jig for the router table? This video shows you the router table circle cutting jig. I made the router circle jig for cutting circles used for lazy susans but realized it worked well for other projects too. My router and router table are old and were cheap. The jig is custom made. I hope this gives you ideas for your own jigs.
Remember: Safety is your responsibility. This video is for entertainment purposes only.
My YouTube Channel:
youtube.com/c/MarriedManWoodworking
Twitter:
twitter.com/marriedmanwood?lang=en
Script:
So this is our base to our circle cutting jig. It has two slots in it. The challenge always is how to keep the center of the board being cut at an exact distance from the straight bit that is doing the cutting. I primarily was looking for something to make lazy susans. I thought why fight what is already happening. The lazy susan hardware already has a center point so whenever I attach this to the board I already have in a couple of bolts. I can just take those and slide them into those slots. I can adjust the diameter of my board by sliding this and then tightening it down where I want it as I do my cut with my straight bit on. I just have to raise the router in the router table a little bit at a time, make my circle, raise it again, make my circle, raise the bit again...it'd be best to show you. With a straight edge I go corner to corner and make a mark. I go from the other corners and make a mark. I take my hardware and put in two bolts on the side that is not facing the board. I line up the other side making sure the corners line up and cross those lines that I just drew. With the screws in there and the bolts already in there, we are ready to turn this over and lower it into position.
Make sure the bit is going to cut into the edge. We can now tighten down the wing nuts. We're now ready for our first turn we will continue to raise the bit a little bit at the time. I'm using a small straight bit. I'll just be incrementally raising it up until we can cut the circle through.
Now the limitation of the way the jig is that I showed you so far is that it can cut round circles from about 18 inches to about 50 inches. What do we do when it's less than 18 inches? We have an accessory to our jig just for that purpose. Our accessory is as simple as a single board with four holes drilled in for bolts to fit through. Those are spaced so that they will slide right into the slots on our primary jig. Once they're in there it allows us the movement back and forth so we can make adjustments. For our next part I found a board that I'm going to use as my base. I've already measured off an area that would make it square and then drew the lines across from what would be the corners to find the center. I attached the hardware. I'll attach this part of the hardware directly to this accessory to the jig at a diameter that's close to what we want in our end result. If I'm a little bit off on where I put it, then I can just slide my jig over and get it right and be able to turn the board as it cuts with the jig accessory secured with wing nuts underneath. I'm now ready to attach my bottom board. I'm gonna line it up here where the bit will end up hitting it. Thanks for watching.
I'll see you next time...I hear my wife calling. I gotta go!!!
00:00 Intro
03:26 Outro
Looking for a circle cutting jig for the router table? This video shows you the router table circle cutting jig. I made the router circle jig for cutting circles used for lazy susans but realized it worked well for other projects too. My router and router table are old and were cheap. The jig is custom made. I hope this gives you ideas for your own jigs.
Remember: Safety is your responsibility. This video is for entertainment purposes only.
My YouTube Channel:
youtube.com/c/MarriedManWoodworking
Twitter:
twitter.com/marriedmanwood?lang=en
Script:
So this is our base to our circle cutting jig. It has two slots in it. The challenge always is how to keep the center of the board being cut at an exact distance from the straight bit that is doing the cutting. I primarily was looking for something to make lazy susans. I thought why fight what is already happening. The lazy susan hardware already has a center point so whenever I attach this to the board I already have in a couple of bolts. I can just take those and slide them into those slots. I can adjust the diameter of my board by sliding this and then tightening it down where I want it as I do my cut with my straight bit on. I just have to raise the router in the router table a little bit at a time, make my circle, raise it again, make my circle, raise the bit again...it'd be best to show you. With a straight edge I go corner to corner and make a mark. I go from the other corners and make a mark. I take my hardware and put in two bolts on the side that is not facing the board. I line up the other side making sure the corners line up and cross those lines that I just drew. With the screws in there and the bolts already in there, we are ready to turn this over and lower it into position.
Make sure the bit is going to cut into the edge. We can now tighten down the wing nuts. We're now ready for our first turn we will continue to raise the bit a little bit at the time. I'm using a small straight bit. I'll just be incrementally raising it up until we can cut the circle through.
Now the limitation of the way the jig is that I showed you so far is that it can cut round circles from about 18 inches to about 50 inches. What do we do when it's less than 18 inches? We have an accessory to our jig just for that purpose. Our accessory is as simple as a single board with four holes drilled in for bolts to fit through. Those are spaced so that they will slide right into the slots on our primary jig. Once they're in there it allows us the movement back and forth so we can make adjustments. For our next part I found a board that I'm going to use as my base. I've already measured off an area that would make it square and then drew the lines across from what would be the corners to find the center. I attached the hardware. I'll attach this part of the hardware directly to this accessory to the jig at a diameter that's close to what we want in our end result. If I'm a little bit off on where I put it, then I can just slide my jig over and get it right and be able to turn the board as it cuts with the jig accessory secured with wing nuts underneath. I'm now ready to attach my bottom board. I'm gonna line it up here where the bit will end up hitting it. Thanks for watching.
I'll see you next time...I hear my wife calling. I gotta go!!!
00:00 Intro
03:26 Outro










