Uploaded October 2026 | Updated November 2026, 3 days ago
After replacing the completely failed battery in this 2016 Ram, the charging system appeared to be working normally again. But before calling it fixed, there was still one important question to answer: what killed the battery in the first place?
In Part 2, we come back after the truck has been driven for a few days and check for a parasitic battery draw. Using a low-amp clamp, I monitor the current as the vehicle’s modules begin shutting down and show why you can’t immediately assume a high initial reading means there’s a problem.
In this video, I show:
- How to check for a parasitic battery draw
- Using a low-amp clamp on a difficult battery cable setup
- Why vehicle modules need time to go to sleep
- How the hood, key, and other inputs can wake modules back up
- Watching the current draw drop as the system powers down
- Confirming there is no excessive parasitic draw
- Why the original bad battery really was the source of the electrical problems
Once the truck completely timed out, the current draw dropped essentially to zero. There was no hidden drain killing the battery — just a failed battery causing some very strange electrical behavior.
It’s another good example of why you should fix the known problem first, verify the repair, and then make sure there isn’t an underlying cause before moving on.
🔧 Looking for Deeper Training?
Whether you're a DIYer, an aspiring tech, or a working technician, ScannerDanner Premium gives you in-depth diagnostic training built around real testing and real troubleshooting:
👉 Join Here – 14 Days for $1
scannerdanner.com/join-scannerdanner-premium.html
On ScannerDanner Premium, you'll get:
*In-depth classroom lectures based on the material in my book
*Case studies with real vehicles brought into class
*Troubleshooting using proven diagnostic methods
*Access to our private forum
*Fundamental training in automotive electrical, electronics, and drivability diagnostics
📘 Want to Learn More About Diagnostics?
Check out my field manual, Engine Performance Diagnostics, available as both an eBook and paperback at:
👉 https://linktr.ee/scannerdanner
ScannerDanner Tools:
https://linktr.ee/scannerdanner
⚠️ Disclaimer:
ScannerDanner LLC is not responsible for misuse, unauthorized changes, or incorrect application of any information provided. Always follow proper safety protocols when using tools, equipment, or procedures discussed in this video. Use this content at your own risk.
0:00 Part 1 Recap
2:27 What Killed the Battery?
2:55 Setting Up the Parasitic Draw Test
4:18 Measuring the Current Draw
5:12 Waiting for the Modules to Go to Sleep
6:44 Hood Switch & Module Wake-Up
7:41 Current Draw Drops to Normal
8:02 No Parasitic Draw Found
9:08 Final Takeaways
After replacing the completely failed battery in this 2016 Ram, the charging system appeared to be working normally again. But before calling it fixed, there was still one important question to answer: what killed the battery in the first place?
In Part 2, we come back after the truck has been driven for a few days and check for a parasitic battery draw. Using a low-amp clamp, I monitor the current as the vehicle’s modules begin shutting down and show why you can’t immediately assume a high initial reading means there’s a problem.
In this video, I show:
- How to check for a parasitic battery draw
- Using a low-amp clamp on a difficult battery cable setup
- Why vehicle modules need time to go to sleep
- How the hood, key, and other inputs can wake modules back up
- Watching the current draw drop as the system powers down
- Confirming there is no excessive parasitic draw
- Why the original bad battery really was the source of the electrical problems
Once the truck completely timed out, the current draw dropped essentially to zero. There was no hidden drain killing the battery — just a failed battery causing some very strange electrical behavior.
It’s another good example of why you should fix the known problem first, verify the repair, and then make sure there isn’t an underlying cause before moving on.
🔧 Looking for Deeper Training?
Whether you're a DIYer, an aspiring tech, or a working technician, ScannerDanner Premium gives you in-depth diagnostic training built around real testing and real troubleshooting:
👉 Join Here – 14 Days for $1
scannerdanner.com/join-scannerdanner-premium.html
On ScannerDanner Premium, you'll get:
*In-depth classroom lectures based on the material in my book
*Case studies with real vehicles brought into class
*Troubleshooting using proven diagnostic methods
*Access to our private forum
*Fundamental training in automotive electrical, electronics, and drivability diagnostics
📘 Want to Learn More About Diagnostics?
Check out my field manual, Engine Performance Diagnostics, available as both an eBook and paperback at:
👉 https://linktr.ee/scannerdanner
ScannerDanner Tools:
https://linktr.ee/scannerdanner
⚠️ Disclaimer:
ScannerDanner LLC is not responsible for misuse, unauthorized changes, or incorrect application of any information provided. Always follow proper safety protocols when using tools, equipment, or procedures discussed in this video. Use this content at your own risk.
0:00 Part 1 Recap
2:27 What Killed the Battery?
2:55 Setting Up the Parasitic Draw Test
4:18 Measuring the Current Draw
5:12 Waiting for the Modules to Go to Sleep
6:44 Hood Switch & Module Wake-Up
7:41 Current Draw Drops to Normal
8:02 No Parasitic Draw Found
9:08 Final Takeaways










![2006 Ford E350 6.0L Turbo Diesel [DID WE FIX IT?]
00:00 - footage from part 1
03:38 - beginning of part 2
04:45 - revisiting the intermittent no com
06:13 - current and history codes
07:47 - we have data!
08:35 - addressing viewer comments
09:35 - something I missed
11:04 - flagship 1 module?
13:50 - CAN diagram
16:50 - why I never checked powers, grounds and com lines
18:18 - test drive
📘 Want to Learn More About Diagnostics?
Check out my field manual, Engine Performance Diagnostics, available as both an eBook and paperback at:
👉 https://linktr.ee/scannerdanner
🔧 Looking for Deeper Training?
Whether youre a DIYer, an aspiring tech, or a professional looking to sharpen your skills, join ScannerDanner Premium for next-level diagnostics training:
👉 Join Here – 14 Days for $1
https://www.scannerdanner.com/join-scannerdanner-premium.html
On ScannerDanner Premium, youll get:
*In-depth classroom lectures straight from my book
*Exclusive case studies with live vehicles pulled into class
*Real-time troubleshooting using proven methods
*Post help requests on our forum
*Fundamental training on diagnosing automotive electrical and electronics systems.
ScannerDanner Tools:
https://linktr.ee/scannerdanner
⚠️ Disclaimer:
ScannerDanner LLC is not responsible for misuse, unauthorized changes, or incorrect application of any information provided. Always follow proper safety protocols when using tools, equipment, or procedures discussed in this video. Use this content at your own risk. 2006 Ford E350 6.0L Turbo Diesel [DID WE FIX IT?]](https://i.ytimg.com/vi/b5S9SPjdNxs/mqdefault.jpg)