Uploaded November 2026 | Updated November 2026, 3 hours ago
PLC addressing for inputs and outputs: a control panel with 3 inputs and 1 output needs 3 X addresses and one Y address, not 3 of each.
โก QUICK ANSWER
PLC I/O allocation treats inputs and outputs as two separate budgets, because a machine's input count and its output count have nothing to do with each other. A control panel using three inputs and one output needs three X addresses and one Y address. Reserving three of each wastes two Y addresses for no reason, and on a ceiling of 16 X and 16 Y that waste is what stops you adding another machine later. In the free ACC PLC simulator you do not work the allocation out by hand: launch a second scene and it takes the lowest offset on each axis that clears every scene already connected and still fits inside the ceiling. Type your own values if you want a different allocation, since every scene card has an X box, a Y box and a Suggest button.
๐ FULL WALKTHROUGH + EXAMPLES
accautomation.ca/run-two-3d-machines-at-once-multi-scene-plc-simulator
โถ RUN IT NOW, FREE IN YOUR BROWSER
accautomation.ca/simulator
๐ WHAT YOU'LL LEARN
โ Allocate inputs and outputs as two independent budgets, not one symmetrical block
โ Size a machine from what it actually uses: three inputs and one output, not three of each
โ See why symmetrical reservations cost you a machine you could have added later
โ Let the allocator take the lowest free offset on each axis automatically
โ Override the suggestion by typing your own X and Y values on the scene card
โ FREQUENTLY ASKED
Q: Why allocate X and Y separately?
A: Because a machine's input count and output count are unrelated. A control panel might read three buttons and drive one lamp. Reserving three outputs for one lamp wastes two addresses permanently.
Q: How does the automatic allocation choose?
A: It takes the lowest offset on each axis that clears every scene already connected and still fits inside the address ceiling. Lowest free, not next round number.
Q: Can I set the allocation myself?
A: Yes. Every scene card has an X box, a Y box and a Suggest button, so you can accept the suggestion or type the allocation you want.
Q: Does any of this apply outside a simulator?
A: All of it. Allocating inputs and outputs independently, and recording what you allocated, is ordinary practice on any real job.
๐ Full walkthrough and examples: accautomation.ca/run-two-3d-machines-at-once-multi-scene-plc-simulator
๐ MORE RESOURCES
โถ Free PLC Simulator: accautomation.ca/simulator
โถ Why two machines cannot both live at X1: youtube.com/shorts/gd8eoHfCxME
โถ Why every scene thinks it is X1: youtube.com/shorts/cNwoLDa9Tb8
โถ Analog and Modbus offset exceptions: youtube.com/shorts/Ue0OkUsc2xo
โถ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
โถ Free eBooks: accautomation.ca (subscribe for download)
๐ RECOMMENDED HARDWARE
โถ Shop: automationdirect.com
โถ Parts Guide: accautomation.ca/purchase-find-parts
๐ฌ Do you allocate I/O symmetrically out of habit? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #PLCSimulator #LearnPLC #PLCTutorial #Shorts
Regards,
Garry
ACC Automation
accautomation.ca
PLC addressing for inputs and outputs: a control panel with 3 inputs and 1 output needs 3 X addresses and one Y address, not 3 of each.
โก QUICK ANSWER
PLC I/O allocation treats inputs and outputs as two separate budgets, because a machine's input count and its output count have nothing to do with each other. A control panel using three inputs and one output needs three X addresses and one Y address. Reserving three of each wastes two Y addresses for no reason, and on a ceiling of 16 X and 16 Y that waste is what stops you adding another machine later. In the free ACC PLC simulator you do not work the allocation out by hand: launch a second scene and it takes the lowest offset on each axis that clears every scene already connected and still fits inside the ceiling. Type your own values if you want a different allocation, since every scene card has an X box, a Y box and a Suggest button.
๐ FULL WALKTHROUGH + EXAMPLES
accautomation.ca/run-two-3d-machines-at-once-multi-scene-plc-simulator
โถ RUN IT NOW, FREE IN YOUR BROWSER
accautomation.ca/simulator
๐ WHAT YOU'LL LEARN
โ Allocate inputs and outputs as two independent budgets, not one symmetrical block
โ Size a machine from what it actually uses: three inputs and one output, not three of each
โ See why symmetrical reservations cost you a machine you could have added later
โ Let the allocator take the lowest free offset on each axis automatically
โ Override the suggestion by typing your own X and Y values on the scene card
โ FREQUENTLY ASKED
Q: Why allocate X and Y separately?
A: Because a machine's input count and output count are unrelated. A control panel might read three buttons and drive one lamp. Reserving three outputs for one lamp wastes two addresses permanently.
Q: How does the automatic allocation choose?
A: It takes the lowest offset on each axis that clears every scene already connected and still fits inside the address ceiling. Lowest free, not next round number.
Q: Can I set the allocation myself?
A: Yes. Every scene card has an X box, a Y box and a Suggest button, so you can accept the suggestion or type the allocation you want.
Q: Does any of this apply outside a simulator?
A: All of it. Allocating inputs and outputs independently, and recording what you allocated, is ordinary practice on any real job.
๐ Full walkthrough and examples: accautomation.ca/run-two-3d-machines-at-once-multi-scene-plc-simulator
๐ MORE RESOURCES
โถ Free PLC Simulator: accautomation.ca/simulator
โถ Why two machines cannot both live at X1: youtube.com/shorts/gd8eoHfCxME
โถ Why every scene thinks it is X1: youtube.com/shorts/cNwoLDa9Tb8
โถ Analog and Modbus offset exceptions: youtube.com/shorts/Ue0OkUsc2xo
โถ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
โถ Free eBooks: accautomation.ca (subscribe for download)
๐ RECOMMENDED HARDWARE
โถ Shop: automationdirect.com
โถ Parts Guide: accautomation.ca/purchase-find-parts
๐ฌ Do you allocate I/O symmetrically out of habit? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #PLCSimulator #LearnPLC #PLCTutorial #Shorts
Regards,
Garry
ACC Automation
accautomation.ca
![PLC Mastering Instructions: Quick Guide [Tutorial]! ๐ช
Master PLC Mastering Instructions: Quick Guide [Tutorial]! ๐ช on the PLC. Step-by-step tutorial with real-world examples.
โก QUICK ANSWER
Modbus on the PLC maps remote coils and registers into local memory. Choose the port (Modbus RTU over RS-485 or Modbus TCP over Ethernet), match baud/parity/slave-ID on both ends, then use a read/write instruction to move holding registers and coils between devices.
๐ FULL STEP-BY-STEP + DOWNLOADS (project file, wiring diagrams, screenshots)
https://accautomation.ca/p1-m622-16dr-mini-plc-contact-and-coil-instructions/
โฑ๏ธ TIMESTAMPS
0:00 - Introduction
0:00 - Adding Instructions
๐ WHAT YOULL LEARN
โ
PLC Mastering Instructions: Quick Guide [Tutorial]! ๐ช step by step on the PLC
โ
Comparison instructions for logic decisions
โ
Practical hands-on approach you can follow along
โ
Real-world tips from manufacturing experience
โ FREQUENTLY ASKED
Q: RTU or TCP โ which do I use?
A: RTU runs over RS-485 serial; TCP runs over Ethernet. Pick whichever your device supports. Both are shown in the full guide.
Q: Why wonโt my Modbus device respond?
A: Confirm baud rate, parity, and slave ID match exactly, and check A/B wiring polarity on RS-485.
๐ Full step-by-step, code & wiring diagrams: https://accautomation.ca/p1-m622-16dr-mini-plc-contact-and-coil-instructions/
๐ MORE RESOURCES
โถ Series: https://accautomation.ca/series/
โถ PLC Beginners Guide: https://accautomation.ca/programming/plc-beginners-guide/
โถ Free eBooks: https://accautomation.ca (subscribe for download)
๐ RECOMMENDED HARDWARE
โถ Shop: https://www.automationdirect.com/
โถ Parts Guide: https://www.accautomation.ca/purchase-find-parts/
๐ฌ Questions? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #AutomationDirect #PLCTutorial #LearnPLC
Regards,
Garry
ACC Automation
http://www.accautomation.ca PLC Mastering Instructions: Quick Guide [Tutorial]! ๐ช](https://i.ytimg.com/vi/yGnJwuLkP2M/mqdefault.jpg)




