Uploaded October 2026 | Updated November 2026, 2 days ago
Zeroing the Pegasus 2, and Cetus (or any other Pixfra rifle scope for that matter) is simple. But here's a few little hacks in a complete, end-to-end zeroing process, that includes setting up multiple profiles, making sure different profiles are easily identified, creating more than one zero range and how to switch between different zero configurations in the field.
Skip to the chapter that you need:
0:00 Part 1 Preparation
5:10 Part 2 How to zeroing
7:20 Part 3 How to set up multiple zero profiles
9:56 Part 4 How to name different zero profiles
11:15 Part 5 How to create more than one zero range
Or listen to the audio while you zero your riflescope.
Thomas Jacks is the UK and Ireland service centre for Pixfra. We don't have many Pixfra rifle scopes returned, but occasionally hear from customers who believe their scope isn't holding zero. In 99% of cases the scope is fine: Sometimes it's down to the fitting, other times a small error in zeroing technique has crept in, or there's been a mistake somewhere in the process (because lets be honest, tech like this is new to a lot of people). It can even be as simple as confusing different profiles when you're out in the field. This video will help you address all of that... but it can't help if there's a problem with the rifle, or it's rail!
Torque settings
ALWAYS CHECK WITH THE MANUFACTURERS INSTRUCTIONS
but here are the settings we use for:
A) Yukon SW30 Rifle Mount
Ring screws: 1.7 - 2Nm (use a spot of screw-lock, such as Loctite 243 on each screw thread)
Base / Rail clamping screws: 4 - 5Nm (no screw lock needed)
B) Pixfra Cetus Quick Release Mount:
Base screws: 5Nm (use a bead of screw-lock, such as Loctite 243 on each bold thread)
Quick release mechanism: Tighten to a point where the lever can still be undone with some effort. no screw-lock needed, as the nut is self locking.)
Zeroing the Pegasus 2, and Cetus (or any other Pixfra rifle scope for that matter) is simple. But here's a few little hacks in a complete, end-to-end zeroing process, that includes setting up multiple profiles, making sure different profiles are easily identified, creating more than one zero range and how to switch between different zero configurations in the field.
Skip to the chapter that you need:
0:00 Part 1 Preparation
5:10 Part 2 How to zeroing
7:20 Part 3 How to set up multiple zero profiles
9:56 Part 4 How to name different zero profiles
11:15 Part 5 How to create more than one zero range
Or listen to the audio while you zero your riflescope.
Thomas Jacks is the UK and Ireland service centre for Pixfra. We don't have many Pixfra rifle scopes returned, but occasionally hear from customers who believe their scope isn't holding zero. In 99% of cases the scope is fine: Sometimes it's down to the fitting, other times a small error in zeroing technique has crept in, or there's been a mistake somewhere in the process (because lets be honest, tech like this is new to a lot of people). It can even be as simple as confusing different profiles when you're out in the field. This video will help you address all of that... but it can't help if there's a problem with the rifle, or it's rail!
Torque settings
ALWAYS CHECK WITH THE MANUFACTURERS INSTRUCTIONS
but here are the settings we use for:
A) Yukon SW30 Rifle Mount
Ring screws: 1.7 - 2Nm (use a spot of screw-lock, such as Loctite 243 on each screw thread)
Base / Rail clamping screws: 4 - 5Nm (no screw lock needed)
B) Pixfra Cetus Quick Release Mount:
Base screws: 5Nm (use a bead of screw-lock, such as Loctite 243 on each bold thread)
Quick release mechanism: Tighten to a point where the lever can still be undone with some effort. no screw-lock needed, as the nut is self locking.)










