Uploaded March 2019 | Updated November 2026, 3 hours ago
Features:
1. 12S / 200 amp. 2oz copper.
2. Onboard LC Filter.
3. Onboard 5v/3.5 amp Sbec
4. Plug & Play ESC/RX/Vtx/Cam
5. Independent or synced throttle control.
6. Calibrate esc(s) independently.
7. 45mm x 35mm
WHAT IS IT!
It’s a PDB meant for twin motor (wing or plane) pilots looking for an easy way to install electronics. It takes out all the work of soldering together your own pigtail mess to accommodate escs, rx wires, external sbecs, vtx and Fpv cam. This board would also suite single motor builders as well.
It was designed and collaborated between Cheng Lin of CL Racing, myself, Derrick Miller and Ruben from Sweepwings over the past couple of months. The one pictured is a prototype. Version 1.0.** Specifications & Features:
1. Four individual pads for multiple power sources (parallel). At minimum one pad is to be used for input resulting in power available at the three other pads for output.
2. Video transmitter output and Fpv cam input connections. Simply connect your Vtx and Fpv cam. Voltage of lipos used is what each receive.
3. Built in LC Filter to provide clean video.
4. Built in 5v/3.5amp SBEC for setups that use escs without Sbecs. Ie quad escs.
5. Ability to piggy back onboard sbec amps with esc sbecs. Hook up ANY esc with an sbec and those sbecs power will be added to the already 3.5amps on the board. For example two wing escs wih 3 amps a piece would result in 9.5 amps available for rx/servos power. Diode protected.
6. Ability to use one single servo wire for throttle control of both motors. Bridged by a small jumper. Or leave separate for channel mixing. Ie differential thrust control.
7. Board ratings: 60v / 200amp
8. 45mm x 35mm
Ps. Please Like & Share would ya. 👍
Features:
1. 12S / 200 amp. 2oz copper.
2. Onboard LC Filter.
3. Onboard 5v/3.5 amp Sbec
4. Plug & Play ESC/RX/Vtx/Cam
5. Independent or synced throttle control.
6. Calibrate esc(s) independently.
7. 45mm x 35mm
WHAT IS IT!
It’s a PDB meant for twin motor (wing or plane) pilots looking for an easy way to install electronics. It takes out all the work of soldering together your own pigtail mess to accommodate escs, rx wires, external sbecs, vtx and Fpv cam. This board would also suite single motor builders as well.
It was designed and collaborated between Cheng Lin of CL Racing, myself, Derrick Miller and Ruben from Sweepwings over the past couple of months. The one pictured is a prototype. Version 1.0.** Specifications & Features:
1. Four individual pads for multiple power sources (parallel). At minimum one pad is to be used for input resulting in power available at the three other pads for output.
2. Video transmitter output and Fpv cam input connections. Simply connect your Vtx and Fpv cam. Voltage of lipos used is what each receive.
3. Built in LC Filter to provide clean video.
4. Built in 5v/3.5amp SBEC for setups that use escs without Sbecs. Ie quad escs.
5. Ability to piggy back onboard sbec amps with esc sbecs. Hook up ANY esc with an sbec and those sbecs power will be added to the already 3.5amps on the board. For example two wing escs wih 3 amps a piece would result in 9.5 amps available for rx/servos power. Diode protected.
6. Ability to use one single servo wire for throttle control of both motors. Bridged by a small jumper. Or leave separate for channel mixing. Ie differential thrust control.
7. Board ratings: 60v / 200amp
8. 45mm x 35mm
Ps. Please Like & Share would ya. 👍










