Uploaded May 2025 | Updated November 2026, 12 hours ago
We look around the MacG Racing Taranis GT3 Racing Car
The Taranis was designed and built in 2015 with the goal of being a no compromises, endurance GT racing car – a goal which the team accomplished with flying colours. With the doors and windscreen being utilised from their previous Ultima GTR, the entire car was designed and built from scratch around these basic components. The car has taken numerous overall wins and podiums between 2016 and 2022 in the Britcar Endurance Championship/British Endurance Championship, demonstrating that in the right hands this car is capable of being competitive with (and beating) the latest GT3 factory built racecars.
This car offers full GT3 performance at a lower price and a much lower running cost than a GT3 car, and is sold ready to race, aside from setup and decals. The car is eligible for many Championships including British Endurance Championship, GT Cup, Supercar Challenge, Castle Coombe GT Championship and many others. We can also continue to supply spares for the car should they be required.
The full specification is as follows:
MacG Racing designed tubular frame chassis manufactured from ROPT510/T45 seamless tubing (generally 50x2mm)
Full aero kit including front splitter, flat floor, diffuser, canards and adjustable bi plane rear wing
650bhp GM LS7 fully forged race engine, with Dailey dry sump system, extensive upgrades over stock (fuel and intake system), rebuilt start 2022 (~15 hours running since rebuild)
Albins ST6-M 6 speed sequential transmission with drop gears, adjustable LSD (6 hours running since rebuild) with Geartronics paddleshift
Triple plate ceramic race clutch with brand new plates and spring (2 hours running since rebuilt)
ATL 100 litre fuel cell, with ATL quick fillers
Motec M800 ECU, SDL3 dash with full logging, driver adjustable traction control, driver adjustable map switch, pit lane speed limiter, light flasher, with extensive sensors on the vehicle
Titan EPAS
MacG Racing designed front and rear uprights, wishbones and roll bars with Quantum 2 way adjustable dampers
AP Racing 6 pot endurance specification brake calipers on the front with 378x36mm discs, and 4 pots on the rear with 330x32 discs. Front discs are brand new.
Braid flowformed 13x18” wheels at the rear, 11x18” wheels at the front, all centrelock, running 310/705 and 285/680 racing slicks respectively
High intensity LED headlights with DRL's
4 onboard JLS airjacks
Full stainless steel exhaust system with repackable silencers
100 litre ATL FIA approved fuel tank and quick fill dry break fuel system
Tillet FIA approved race seat and FIA approved 6 point harness (these need replacing for 2023)
The car also comes with a significant spares packaging, including:
Comprehensive gearbox spares package
10 rims with wet and dry tyres
Radiator
Various bodywork moulds including side pods and front clam
Alternative drop gear set
Rear upright and various wishbones
Suspension joints, CV joints
Splitter, headlight covers and canards
Steering rack
Various other small parts such as engine drive belts, dry sump belt, filters etc
MacG Racing can continue to provide spares as necessary for the new owner.
For further information please contact: info@macgracing.co.uk
#gt3racecar #taranis #gt3kitcar
We look around the MacG Racing Taranis GT3 Racing Car
The Taranis was designed and built in 2015 with the goal of being a no compromises, endurance GT racing car – a goal which the team accomplished with flying colours. With the doors and windscreen being utilised from their previous Ultima GTR, the entire car was designed and built from scratch around these basic components. The car has taken numerous overall wins and podiums between 2016 and 2022 in the Britcar Endurance Championship/British Endurance Championship, demonstrating that in the right hands this car is capable of being competitive with (and beating) the latest GT3 factory built racecars.
This car offers full GT3 performance at a lower price and a much lower running cost than a GT3 car, and is sold ready to race, aside from setup and decals. The car is eligible for many Championships including British Endurance Championship, GT Cup, Supercar Challenge, Castle Coombe GT Championship and many others. We can also continue to supply spares for the car should they be required.
The full specification is as follows:
MacG Racing designed tubular frame chassis manufactured from ROPT510/T45 seamless tubing (generally 50x2mm)
Full aero kit including front splitter, flat floor, diffuser, canards and adjustable bi plane rear wing
650bhp GM LS7 fully forged race engine, with Dailey dry sump system, extensive upgrades over stock (fuel and intake system), rebuilt start 2022 (~15 hours running since rebuild)
Albins ST6-M 6 speed sequential transmission with drop gears, adjustable LSD (6 hours running since rebuild) with Geartronics paddleshift
Triple plate ceramic race clutch with brand new plates and spring (2 hours running since rebuilt)
ATL 100 litre fuel cell, with ATL quick fillers
Motec M800 ECU, SDL3 dash with full logging, driver adjustable traction control, driver adjustable map switch, pit lane speed limiter, light flasher, with extensive sensors on the vehicle
Titan EPAS
MacG Racing designed front and rear uprights, wishbones and roll bars with Quantum 2 way adjustable dampers
AP Racing 6 pot endurance specification brake calipers on the front with 378x36mm discs, and 4 pots on the rear with 330x32 discs. Front discs are brand new.
Braid flowformed 13x18” wheels at the rear, 11x18” wheels at the front, all centrelock, running 310/705 and 285/680 racing slicks respectively
High intensity LED headlights with DRL's
4 onboard JLS airjacks
Full stainless steel exhaust system with repackable silencers
100 litre ATL FIA approved fuel tank and quick fill dry break fuel system
Tillet FIA approved race seat and FIA approved 6 point harness (these need replacing for 2023)
The car also comes with a significant spares packaging, including:
Comprehensive gearbox spares package
10 rims with wet and dry tyres
Radiator
Various bodywork moulds including side pods and front clam
Alternative drop gear set
Rear upright and various wishbones
Suspension joints, CV joints
Splitter, headlight covers and canards
Steering rack
Various other small parts such as engine drive belts, dry sump belt, filters etc
MacG Racing can continue to provide spares as necessary for the new owner.
For further information please contact: info@macgracing.co.uk
#gt3racecar #taranis #gt3kitcar










