Uploaded December 2024 | Updated November 2026, 6 hours ago
Note: T16D, coach transmitter, with hardware version of V1.0.2 or above supports wireless trainer cable.
There are two methods to use the trainer function for T16D/T12D. One is to connect via trainer cable and the other is to connect via RadioLink wireless trainer cable.
In this tutorial, I’m going to show the trainer function with wireless trainer cable connection.
Here is RadioLink type-C wireless trainer cable we need. You can buy it on RadioLink official store.
We also need a T16D, which works as a coach transmitter, a T12D which works as a student transmitter, a R16F which is bound to T16D successfully. I connect a servo to the channel 1 of the receiver to better show the trainer function.
We also need a receiver which supports PPM signal, because the wireless trainer cable supports receivers of PPM signal. So I use R8FM mini receiver. This R8FM has already been bound to the student transmitter T12D.
By the way, if you want to use T16D/T12D as a coach transmitter and you want to use the wireless trainer cable, please check the hardware version of your T16D.
T16D, coach transmitter, with hardware version of V1.0.2 or above supports wireless trainer cable.
Enter MAIN MENU--Transmitter Settings--ABOUT. The hardware version is V1.0.2, so this T16D supports wireless trainer cable. If the hardware version of your coach transmitter T16D is below V1.0.2, please use the trainer cable.
How to use the trainer function?
First, connect the wireless trainer cable. I connect R8FM to the end of the trainer cable. And connect the trainer cable to the type-c port of T16D.
Then. Set trainer function on the two transmitters.
Set the coach transmitter T16D. Enter the MAIN MENU--Transmitter Settings--TRAINER. And I assign SWA_UP to control the trainer function, Set the state to ON. That means when SWA is pushed up, the trainer function is turned on; when SWA is pushed down, the trainer function is turned off.
T16D is the coach transmitter, so I set the mode to Coach mode.
And I need to set PWR to ON, which means the type-C port can supply power to the PPM receiver. And the LED of R8FM is powered on. We can see the LED of the receiver is in red, which means it is in PPM working mode.
Then. Set the student transmitter T12D. Enter the MAIN MENU--Transmitter Settings--TRAINER. I keep the switch NULL, because I don’t need switch to control it. You can assign a switch according to your needs. Set the state to ON. T12D is the student transmitter, so I set the mode to Student mode. Here are the settings of T12D.
By the way, to make the trainer function works well, please make sure all the settings of the coach transmitter is the same with the settings of the student transmitter.
The settings are done. Return to servo display. Push SWA down, the trainer function is turned off. The servo is connected to channel 1 of the receiver. So I push the joystick of T16D, the servo is controlled by the coach transmitter, T16D.
Push SWA up, the trainer function is turned on. Push the joystick of T16D, there is no response. Push the joystick of T12D, we can see the servo is working, which means the receiver is controlled by the student transmitter, T12D.
You can push use SWA to turn on or turn off the trainer function.
But here is one problem. When I push the channel 1 joystick of the student transmitter, the servo value on the student transmitter is different from the servo value on the coach transmitter. That is because we need to adjust the PPM value on T16D to make the student transmitter totally match the coach transmitter. How to adjust the PPM value here? Please follow the below steps.
1.Make sure the joysticks of the trainer and student transmitters have been correctly calibrated. Both of them have been calibrated before.
2.Adjust the maximum servo value of channel 1 of the student transmitter. Enter END POINT. The EPA of channel 1 of T8FB defaults to 100. We need to set it to the largest value 120.
3.The trainer function is turned on. Push the channel 1 joystick of the student transmitter to the left and right sides. We can view the PPM value of CH1 IN of the student transmitter on T16D. We can see the PPM maximum is 1625, PPM minimum is 375, PPM middle is about 1000. So we need to adjust PPM MIN to 375, set PPM MAX to 1625, and PPM MID to 1000.
4.After the setting, set the EPA of the channel 1 of the student transmitter back to the original value. It defaults to 100. So I set it back to 100.
The adjustment of PPM value is done. Return to servo display. Push down, the trainer function is turned off. T16D controls the servo. Here is the movement of the servo.
If you are using transmitters from other brands, you can also refer to the steps to adjust the PPM value.
So that is the trainer function of T16D and T12D with Wireless Trainer Cable.
For more details of T16D, please refer to the link:
radiolink.com/t16d
For more details of T12D, please refer to the link:
radiolink.com/t12d
Note: T16D, coach transmitter, with hardware version of V1.0.2 or above supports wireless trainer cable.
There are two methods to use the trainer function for T16D/T12D. One is to connect via trainer cable and the other is to connect via RadioLink wireless trainer cable.
In this tutorial, I’m going to show the trainer function with wireless trainer cable connection.
Here is RadioLink type-C wireless trainer cable we need. You can buy it on RadioLink official store.
We also need a T16D, which works as a coach transmitter, a T12D which works as a student transmitter, a R16F which is bound to T16D successfully. I connect a servo to the channel 1 of the receiver to better show the trainer function.
We also need a receiver which supports PPM signal, because the wireless trainer cable supports receivers of PPM signal. So I use R8FM mini receiver. This R8FM has already been bound to the student transmitter T12D.
By the way, if you want to use T16D/T12D as a coach transmitter and you want to use the wireless trainer cable, please check the hardware version of your T16D.
T16D, coach transmitter, with hardware version of V1.0.2 or above supports wireless trainer cable.
Enter MAIN MENU--Transmitter Settings--ABOUT. The hardware version is V1.0.2, so this T16D supports wireless trainer cable. If the hardware version of your coach transmitter T16D is below V1.0.2, please use the trainer cable.
How to use the trainer function?
First, connect the wireless trainer cable. I connect R8FM to the end of the trainer cable. And connect the trainer cable to the type-c port of T16D.
Then. Set trainer function on the two transmitters.
Set the coach transmitter T16D. Enter the MAIN MENU--Transmitter Settings--TRAINER. And I assign SWA_UP to control the trainer function, Set the state to ON. That means when SWA is pushed up, the trainer function is turned on; when SWA is pushed down, the trainer function is turned off.
T16D is the coach transmitter, so I set the mode to Coach mode.
And I need to set PWR to ON, which means the type-C port can supply power to the PPM receiver. And the LED of R8FM is powered on. We can see the LED of the receiver is in red, which means it is in PPM working mode.
Then. Set the student transmitter T12D. Enter the MAIN MENU--Transmitter Settings--TRAINER. I keep the switch NULL, because I don’t need switch to control it. You can assign a switch according to your needs. Set the state to ON. T12D is the student transmitter, so I set the mode to Student mode. Here are the settings of T12D.
By the way, to make the trainer function works well, please make sure all the settings of the coach transmitter is the same with the settings of the student transmitter.
The settings are done. Return to servo display. Push SWA down, the trainer function is turned off. The servo is connected to channel 1 of the receiver. So I push the joystick of T16D, the servo is controlled by the coach transmitter, T16D.
Push SWA up, the trainer function is turned on. Push the joystick of T16D, there is no response. Push the joystick of T12D, we can see the servo is working, which means the receiver is controlled by the student transmitter, T12D.
You can push use SWA to turn on or turn off the trainer function.
But here is one problem. When I push the channel 1 joystick of the student transmitter, the servo value on the student transmitter is different from the servo value on the coach transmitter. That is because we need to adjust the PPM value on T16D to make the student transmitter totally match the coach transmitter. How to adjust the PPM value here? Please follow the below steps.
1.Make sure the joysticks of the trainer and student transmitters have been correctly calibrated. Both of them have been calibrated before.
2.Adjust the maximum servo value of channel 1 of the student transmitter. Enter END POINT. The EPA of channel 1 of T8FB defaults to 100. We need to set it to the largest value 120.
3.The trainer function is turned on. Push the channel 1 joystick of the student transmitter to the left and right sides. We can view the PPM value of CH1 IN of the student transmitter on T16D. We can see the PPM maximum is 1625, PPM minimum is 375, PPM middle is about 1000. So we need to adjust PPM MIN to 375, set PPM MAX to 1625, and PPM MID to 1000.
4.After the setting, set the EPA of the channel 1 of the student transmitter back to the original value. It defaults to 100. So I set it back to 100.
The adjustment of PPM value is done. Return to servo display. Push down, the trainer function is turned off. T16D controls the servo. Here is the movement of the servo.
If you are using transmitters from other brands, you can also refer to the steps to adjust the PPM value.
So that is the trainer function of T16D and T12D with Wireless Trainer Cable.
For more details of T16D, please refer to the link:
radiolink.com/t16d
For more details of T12D, please refer to the link:
radiolink.com/t12d