bhadeshia123 | Strong steels for gas turbines, by Martin Rawson, Lecture 9 of 25 @bhadeshia123 | Uploaded November 2021 | Updated October 2024, 6 seconds ago.
Lecture 9, by Dr Martin Rawson, in the series "Steel Research: A global journey", organised by Adreil Wong, Dominik Dziedzic and Steve Ooi to mark the retirement of Harry Bhadeshia.

The main engine shaft in a large aeroengine is made from steel. Martin Rawson traces first the history of the development of superclean alloys that can withstand the onerous conditions of an aeroengine. He then goes on to show the latest developments in aeroengine steels.

phase-trans.msm.cam.ac.uk

$The Titanic disaster and the continuing effort to improve the impact toughness of ferritic steels Professor Debalay Chakrabarti of the Indian Institute of Technology Kharagpur, India, provides a historical context to the brittle failure of ferritic steels, and then goes on to explain the fundamental science of the ductile-brittle transition in steels. He contrasts, using dislocation theory, the difficulty in moving dislocations in ferrite against the relative ease in austenite. This explains why the ductile-brittle transition is generally absent in austenitic steels. Detailed fracture mechanics arguments are presented to estimate the fracture stress as a function of variables such as the grain size, hard-particle cleavage, stress triaxiality etc. Specific comments added after the lecture, on the role of manganese sulphides: Being softer than the matrix, MnS inclusions elongate along the direction of metal-flow during hot-deformation and that creates anisotropy in ductility in toughness, particularly affecting the properties along transverse direction of rolled / forged plates. It was mentioned that MnS decreases toughness at room temperature, but the accurate statement is that it significantly reduces the upper shelf energy level and thus brings down the entire transition curve towards lower energy side.$

1920s Tyrela gramophone - powered by steel

Sigma-phase in alloys of iron: crystal and microstructure

$Stress corrosion cracking and hydrogen embrittlement Dr Clayton Thomas presents at the Warwick Manufacturing Group Seminar organised by Prakash Srirangam. Stress corrosion cracking (SCC) and hydrogen embrittlement (HE) are part of a phenomena called environmentally assisted fracture, which causes the catastrophic failure of metals, at lower than expected loads. Hence over the years it has caused many engineering failures. Some of these failures will be discussed in this webinar, to illustrate how important it is to consider the phenomena when designing components and structures. The methods and standards used to prevent the problem will discussed, and show how they affect material selection and manufacturing. The similarities and differences between SCC and HE are considered and although many mechanisms of the phenomena are well understood, many are not and some examples of these will be discussed. SCC occurs in a range of materials and environments and some of the more common examples will be covered. Also, Hydrogen embrittlement covers a range of failures processes and some of these will be discussed. Hydrogen sulphide causes sulphide stress corrosion cracking, which is a major problem in the oil and gas industry. Hence it must be considered when designing equipment and it strongly influences both the material selection and fabrication and this will also be covered. About Clayton Thomas: Originally from South Wales and currently living in Barnsley, South Yorkshire. Clayton gained a degree in metallurgy at Imperial College, London, and then went to the University of Sheffield and attained a Masters degree in metallurgy (subject of masters thesis was the environmentally assisted fracture in a martensitic stainless steel) and a PhD, investigating offshore corrosion fatigue. He worked for three years at British Steel Technical (in Rotherham) as a metallurgical investigator and then corrosion test laboratory manager, and then joined Cameron (now called One Subsea) as corrosion engineer in 1990, who are a major supplier of oil and gas completion equipment. He eventually became senior metallurgist and worked on major topside and subsea projects, where he was responsible for the material selection and corrosion prevention for all topside and subsea projects and for the metallurgy and welding of equipment. Since 2000, he has have been the director of his own company, Lloyd-Thomas Consultancy Ltd, providing metallurgical support and training. He has continued to work in oil and gas as well as other engineering sectors, such as renewable energy, power engineering, aerospace and biomedical. He has carried out numerous failure investigations and have acted as an expert witness in litigation cases. He has also run over 300 metallurgy courses for companies and colleges on various aspects of metallurgy and an approved trainer for the AMRC, which is part of the University of Sheffield, as well as providing metallurgy training courses for the Institute of Materials, Minerals and Mining and the Engineering Training Institute of Australia.$

Crystallography, deformation & texture. Lecture 7 of 9

Prof Sir Harry Bhadeshia ASPPRC 40th Celebration Lecture: Visionary Steels

Molybdenum and niobium silicide based intermetallic alloys

Pure iron - the phase diagram - terapascal pressures, 20000 K

Freight train through Cambridge Central Railway Station

Strong steels for gas turbines, by Martin Rawson, Lecture 9 of 25 @bhadeshia123