Uploaded October 2015 | Updated November 2026, 3 hours ago
Making A Right Angled Screwdriver, by Clickspring
A right angled screwdriver isn't a tool you'll need to use often, but its great to have one on hand for things like inserting a mainspring hook into a clock barrel wall.
The main project video that this video is related to is "How To Make A Clock In The Home Machine Shop - Part 13 - Depthing And Planting The Train ": youtube.com/watch?v=O8xIjsaDlN8
Join YouTube Channel Memberships here: youtube.com/channel/UCworsKCR-Sx6R6-BnIjS2MA/join
Become a Clickspring Patron here: patreon.com/clickspring/membership
You can also help me make these videos by purchasing via the following Amazon Affiliate links:
Cameras used in this video:
Panasonic GH5 - amzn.to/2rEzhh2
Panasonic X920 - amzn.to/2wzxxdT
Tools & Shop Products:
"Solidworks 2013 Bible": amzn.to/2FObS1D
"Basic Lathework (Workshop Practice Series)" - amzn.to/2twVNIU
"Lathework: A Complete Course (Workshop Practice Series)" - amzn.to/2yBv4Rb
Loctite 231097 603 Retaining Compound, 10 mL: amzn.to/2pid6vR
Norton 1-by-2-by-8-Inch Fine/Coarse India Combination Oilstone, Red: amzn.to/2tTEPb0
Saint Gobain (Norton) - 4 Arkansas Stones + case:
Blue Matador Abrasive Paper - amzn.to/2IAFiBT
Ask Me A Question:
clickspringprojects.com/contact.html
Abbreviated Transcript:
00:05 I'm in the process of fabricating a mainspring hook to put into the clock barrel, and a threaded insert is a nice convenient
way to get the job done. But I need a lot more leverage to get the insert as tight as it needs to be.
00:16 The obvious choice is to put in a slot, and then use a screwdriver, but of course a normal screwdriver can't reach in properly without risking damage to both parts. What I really need is something like this: A right angled screwdriver.
00:29 Normally screwdriver tips would be made from a hardened steel, but this tool will only get used a few dozen times over its lifetime, so I'm going to keep it simple, and just use a section of this mild steel.
00:39 The grip pattern I have in mind is the simple grooved pattern that you might have seen me use before on some other small hand tools, like this scriber and transfer gauge; its simple to form and works great.
00:49 All parts will be bonded together using Loctite 603; If I need to change out the tips later, a bit of heat will easily break the bond. So lets get started!
00:59 Beginning with the handle, I faced both ends, and then drilled out the center, to be a slip fit over the rod that will become the body of the tool.
01:47 To extend the pattern, I pulled the stock out further, registered the tool in one of the existing grooves, and then continued as before. After parting off, the ends were given a light chamfer, and that's the handle complete.
02:19 Next I started work on the screwdriver tips. Firstly with a quick facing cut to clean up the stock.
02:44 I want the tips to taper back to the shaft
when fixed in place, so I used a form tool to put a nice curve at what will become the base of the screwdriver tip.
03:00 I followed with a quick spot drill and as for the handle, I drilled out the tips to be a slip fit on the rod that will become the body of the tool.
03:34 Now I'd also like the blade to narrow towards the other end, so I've set the topslide over to 3 degrees, to cut a short taper. And while I was set up, I took a few moments to make some extras, to have in stock as spares for the future.
04:02 I'm using a length of drill rod for the body
of the tool, and the tips are temporarily held onto that rod with super glue, while I shape the flats of the blade on the belt sander.
04:10 I'll break that super glue bond later with a little heat when I need to release them. And this little holding block makes indexing from side to side dead easy.
04:20 Now the belt sander makes quick work of this sort of thing, but it does generate quite a bit of heat, so I needed to keep the work cool. I didn't want that super glue bond letting go just yet.
04:37 OK, so the tips are in the shape that I want, and a little heat from the butane torch releases the super glue bond.
04:52 Next I formed the drill rod shaft into that right angled shape, using the propane torch to soften the steel. And then I trimmed the ends on the belt sander, and also cleaned off the heat oxide with some emery paper.
05:28 At this point the grip was bonded in place with a spot of Loctite, making sure that it was in the center of the tool.
05:41 So I set that aside to cure, and while that was happening, I decided to stone the tips to make them a look a bit more presentable.
05:56 And finally I bonded the tips to the shaft,
being careful to set them at 90 degrees to each other.
Making A Right Angled Screwdriver, by Clickspring
Making A Right Angled Screwdriver, by Clickspring
A right angled screwdriver isn't a tool you'll need to use often, but its great to have one on hand for things like inserting a mainspring hook into a clock barrel wall.
The main project video that this video is related to is "How To Make A Clock In The Home Machine Shop - Part 13 - Depthing And Planting The Train ": youtube.com/watch?v=O8xIjsaDlN8
Join YouTube Channel Memberships here: youtube.com/channel/UCworsKCR-Sx6R6-BnIjS2MA/join
Become a Clickspring Patron here: patreon.com/clickspring/membership
You can also help me make these videos by purchasing via the following Amazon Affiliate links:
Cameras used in this video:
Panasonic GH5 - amzn.to/2rEzhh2
Panasonic X920 - amzn.to/2wzxxdT
Tools & Shop Products:
"Solidworks 2013 Bible": amzn.to/2FObS1D
"Basic Lathework (Workshop Practice Series)" - amzn.to/2twVNIU
"Lathework: A Complete Course (Workshop Practice Series)" - amzn.to/2yBv4Rb
Loctite 231097 603 Retaining Compound, 10 mL: amzn.to/2pid6vR
Norton 1-by-2-by-8-Inch Fine/Coarse India Combination Oilstone, Red: amzn.to/2tTEPb0
Saint Gobain (Norton) - 4 Arkansas Stones + case:
Blue Matador Abrasive Paper - amzn.to/2IAFiBT
Ask Me A Question:
clickspringprojects.com/contact.html
Abbreviated Transcript:
00:05 I'm in the process of fabricating a mainspring hook to put into the clock barrel, and a threaded insert is a nice convenient
way to get the job done. But I need a lot more leverage to get the insert as tight as it needs to be.
00:16 The obvious choice is to put in a slot, and then use a screwdriver, but of course a normal screwdriver can't reach in properly without risking damage to both parts. What I really need is something like this: A right angled screwdriver.
00:29 Normally screwdriver tips would be made from a hardened steel, but this tool will only get used a few dozen times over its lifetime, so I'm going to keep it simple, and just use a section of this mild steel.
00:39 The grip pattern I have in mind is the simple grooved pattern that you might have seen me use before on some other small hand tools, like this scriber and transfer gauge; its simple to form and works great.
00:49 All parts will be bonded together using Loctite 603; If I need to change out the tips later, a bit of heat will easily break the bond. So lets get started!
00:59 Beginning with the handle, I faced both ends, and then drilled out the center, to be a slip fit over the rod that will become the body of the tool.
01:47 To extend the pattern, I pulled the stock out further, registered the tool in one of the existing grooves, and then continued as before. After parting off, the ends were given a light chamfer, and that's the handle complete.
02:19 Next I started work on the screwdriver tips. Firstly with a quick facing cut to clean up the stock.
02:44 I want the tips to taper back to the shaft
when fixed in place, so I used a form tool to put a nice curve at what will become the base of the screwdriver tip.
03:00 I followed with a quick spot drill and as for the handle, I drilled out the tips to be a slip fit on the rod that will become the body of the tool.
03:34 Now I'd also like the blade to narrow towards the other end, so I've set the topslide over to 3 degrees, to cut a short taper. And while I was set up, I took a few moments to make some extras, to have in stock as spares for the future.
04:02 I'm using a length of drill rod for the body
of the tool, and the tips are temporarily held onto that rod with super glue, while I shape the flats of the blade on the belt sander.
04:10 I'll break that super glue bond later with a little heat when I need to release them. And this little holding block makes indexing from side to side dead easy.
04:20 Now the belt sander makes quick work of this sort of thing, but it does generate quite a bit of heat, so I needed to keep the work cool. I didn't want that super glue bond letting go just yet.
04:37 OK, so the tips are in the shape that I want, and a little heat from the butane torch releases the super glue bond.
04:52 Next I formed the drill rod shaft into that right angled shape, using the propane torch to soften the steel. And then I trimmed the ends on the belt sander, and also cleaned off the heat oxide with some emery paper.
05:28 At this point the grip was bonded in place with a spot of Loctite, making sure that it was in the center of the tool.
05:41 So I set that aside to cure, and while that was happening, I decided to stone the tips to make them a look a bit more presentable.
05:56 And finally I bonded the tips to the shaft,
being careful to set them at 90 degrees to each other.
Making A Right Angled Screwdriver, by Clickspring










