Uploaded July 2020 | Updated November 2026, 4 hours ago
Many new snapon scope users struggle to understand the way the Snapon scope captures information and how the zoom feature works. There are a couple analogies that I would like to use to describe the zoom feature instead of using the term buffer. I like to think of the snapon as writing in a book. Each time a waveform is displayed on the live scope screen a new page is put into the book with that image on it. Because of this we need to make sure we are looking at the waveform in a way that we can see the fine detail of the wave even if we cannot see the big picture yet. Think of reading a book, you work your way through the story and may not understand the whole plot until the end and reflect back across all that you have read. Once we have enough individual pages to fill our book we can hit the stop button on the scope. If we want to reflect back on the whole we can press the magnifying glass. This will lay all the pages of the book out on the table so we can see the whole story but we cant see the details. Now we can select the part of the book we want to review in one of several ways. We can drag the dashed vertical line over the section we want to focus on and then click on the magnifying glass again to adjust our view. The second way is to double tap the screen where we want to focus in and the scope will go back to the single page view.
If we look at the magnification options you would think we have a zoom in feature because we have x1, x2 , x4... These numbers are not how many time we are zooming in but instead how many times we are zooming out. If you think of it as a book we was use the numbers to represent how many pages are on the table. x1 page we can see the fine detail but that might not be enough of the story because the paragraph might continue onto the next page. x2 pages might let finish the paragraph but not enough to understand. 4x pages might be enough to see the entire chapter and we start to understand what we are looking at. The numbers go on and on as we lay pages out on the table.
The next analogy is to to think of the forest. Most scopes take a picture of the forest and allow you to zoom into a single tree. Snapon takes pictures of one tree after another and we zoom out later to view the entire forest. x1 tree, x2 trees, x4 trees and so on.
I hope this help new and experienced scope users to view the zoom feature in a different way.
Many new snapon scope users struggle to understand the way the Snapon scope captures information and how the zoom feature works. There are a couple analogies that I would like to use to describe the zoom feature instead of using the term buffer. I like to think of the snapon as writing in a book. Each time a waveform is displayed on the live scope screen a new page is put into the book with that image on it. Because of this we need to make sure we are looking at the waveform in a way that we can see the fine detail of the wave even if we cannot see the big picture yet. Think of reading a book, you work your way through the story and may not understand the whole plot until the end and reflect back across all that you have read. Once we have enough individual pages to fill our book we can hit the stop button on the scope. If we want to reflect back on the whole we can press the magnifying glass. This will lay all the pages of the book out on the table so we can see the whole story but we cant see the details. Now we can select the part of the book we want to review in one of several ways. We can drag the dashed vertical line over the section we want to focus on and then click on the magnifying glass again to adjust our view. The second way is to double tap the screen where we want to focus in and the scope will go back to the single page view.
If we look at the magnification options you would think we have a zoom in feature because we have x1, x2 , x4... These numbers are not how many time we are zooming in but instead how many times we are zooming out. If you think of it as a book we was use the numbers to represent how many pages are on the table. x1 page we can see the fine detail but that might not be enough of the story because the paragraph might continue onto the next page. x2 pages might let finish the paragraph but not enough to understand. 4x pages might be enough to see the entire chapter and we start to understand what we are looking at. The numbers go on and on as we lay pages out on the table.
The next analogy is to to think of the forest. Most scopes take a picture of the forest and allow you to zoom into a single tree. Snapon takes pictures of one tree after another and we zoom out later to view the entire forest. x1 tree, x2 trees, x4 trees and so on.
I hope this help new and experienced scope users to view the zoom feature in a different way.










