Uploaded September 2021 | Updated November 2026, 2 hours ago
Aaron Murakami walks through assembling the Lakhovsky MWO supplied with printed-circuit antennas in place of the rings. The boards carry Eric Dollard's twelve golden-ratio rings exactly to scale, with strips on the back layer sitting over the gaps to add the capacitance the tuning needs, which the look-alike boards online do not have. Assembly needs a screwdriver and three sockets, everything hand-tight into plastic: base and upright, saddle, coil with the antenna toward the chair, then the antenna on its brass terminal with washers and an acorn nut, about a minute a side. The cabling is colour-coded, three red and one black, with a ground wire to an earth rod for the Lakhovsky mode and the green jack never used; the antennas must measure exactly 33 inches edge to edge with the supplied cables, since the cable length is part of the tuning. Recommended settings are 50 percent spark gap and 50 percent intensity for 15 to 30 minutes, with no corona or sparks off the antennas in proper use. He then fits the optional oscillation transformer, bypassing the primary and centre-tapping to the green jack, to run the same unit in the balanced Tesla mode, and shows the neutral spot with a fluorescent tube: bright at either antenna and dark at the midpoint, which the Lakhovsky wiring never produces.
Chapters
0:00 PCB antennas: golden ratio, to scale
1:36 The capacitive strips the copies lack
3:07 Tools, base and upright
4:39 Saddle, coil and antenna
9:13 Power, cables and the ground rod
11:45 33 inches, and only these cables
13:17 Spark gap and intensity at 50 percent
14:18 Spark test and the tube
16:17 Wiring the oscillation transformer
18:20 Balanced mode and the neutral spot
22:31 The neutral spot again, at the shop
emediapress.com/mwo
ericpdollard.com/donate
emediapress.com
emediapress.com/energytimes
Posted 2021-09-30.
Aaron Murakami walks through assembling the Lakhovsky MWO supplied with printed-circuit antennas in place of the rings. The boards carry Eric Dollard's twelve golden-ratio rings exactly to scale, with strips on the back layer sitting over the gaps to add the capacitance the tuning needs, which the look-alike boards online do not have. Assembly needs a screwdriver and three sockets, everything hand-tight into plastic: base and upright, saddle, coil with the antenna toward the chair, then the antenna on its brass terminal with washers and an acorn nut, about a minute a side. The cabling is colour-coded, three red and one black, with a ground wire to an earth rod for the Lakhovsky mode and the green jack never used; the antennas must measure exactly 33 inches edge to edge with the supplied cables, since the cable length is part of the tuning. Recommended settings are 50 percent spark gap and 50 percent intensity for 15 to 30 minutes, with no corona or sparks off the antennas in proper use. He then fits the optional oscillation transformer, bypassing the primary and centre-tapping to the green jack, to run the same unit in the balanced Tesla mode, and shows the neutral spot with a fluorescent tube: bright at either antenna and dark at the midpoint, which the Lakhovsky wiring never produces.
Chapters
0:00 PCB antennas: golden ratio, to scale
1:36 The capacitive strips the copies lack
3:07 Tools, base and upright
4:39 Saddle, coil and antenna
9:13 Power, cables and the ground rod
11:45 33 inches, and only these cables
13:17 Spark gap and intensity at 50 percent
14:18 Spark test and the tube
16:17 Wiring the oscillation transformer
18:20 Balanced mode and the neutral spot
22:31 The neutral spot again, at the shop
emediapress.com/mwo
ericpdollard.com/donate
emediapress.com
emediapress.com/energytimes
Posted 2021-09-30.










