S-300B Radial Lead Molding & Taping Machine: How It Works in 3D @Smthelping
S-300B Radial Lead Molding & Taping Machine: How It Works in 3D  @Smthelping
Uploaded November 2026 | Updated November 2026, 3 hours ago
Stop forming and taping radial components by hand. See how the S-300B fully automatic high-speed molding and taping machine from Southern Machinery works, in 3D from the real CAD model: loose LEDs, capacitors and resistors go in, formed, tested and sealed tape comes out, at 180 +/- 20 parts per minute.

How it works: a vibratory bowl orients loose radial parts onto a linear track. Walking-beam transfer clips carry each part station by station: the leads are spread, then pressed in an integrated forming die to 2.5, 3.5 or 5.0 mm pitch. Polarity is checked and a reversed part is turned 180 deg by a stepper-driven re-orientation clamp instead of being rejected. With the optional tester, capacitance and resistance are measured and failed parts drop into the reject chute. Leads are trimmed, good parts are placed onto 12.7 mm pitch paper tape, a heated top tape seals the leads, sprocket holes are punched and a servo indexer advances the tape one pitch at a time. The finished tape is folded into an ammo box or wound on a reel, ready for your radial inserter.
Key data (S-300B product sheet)
- Capacity: 180 +/- 20 pcs/min
- Body diameter: Ø4-Ø10 mm, two fixture sets (Ø4-6, Ø8-10)
- Formed lead pitch: 2.5 / 3.5 / 5.0 mm (7.5, 10, 15 mm and above to order)
- Hole pitch / hole diameter: 12.7 mm / 4.1 mm (other pitches on request)
- Taping height: 17-21 mm; product length 5-30 mm
- Packing: boxed (ammo) or coiled (reel)
- Servo control system replaces the traditional clutch
- Imported cams ground to 0.01 mm, design service life 15+ years
- Touch-screen operation, PLC or single-chip control
- 220 V / 50 Hz / 1.6 kW; air 4-5 kg/cm^2
Final configuration (fixtures, pitch, tester) is confirmed after reviewing your component list.

Chapters
00:00 Hand taping is the bottleneck
00:13 S-300B fully automatic molding & taping machine
00:28 Feed: vibratory bowl, linear track, transfer clips
00:40 Lead spread + integrated forming die (2.5 / 3.5 / 5.0 mm)
00:56 Polarity check, re-orientation, C/R value test, reject chute
01:12 Taping: 12.7 mm paper tape, heated top tape, punch, servo indexer
01:25 Packing: ammo box or reel
01:32 Servo drive and imported 0.01 mm cams
01:47 Specification
02:00 The result
02:09 Send us your component list

Machine geometry from the CAD model; components, paper and top tape, tape paths and motion timing shown illustratively, slowed for clarity in the close-ups.

Product page: smthelp.com
Contact: info@smthelp.com - WhatsApp +86 136 0256 2576
Southern Machinery, SMT & THT automation since 2011.
Subscribe: youtube.com/c/Smthelping

#THT #RadialTaping #PCBA #EMS #ElectronicsManufacturing #TapingMachine #Automation
S-300B Radial Lead Molding & Taping Machine: How It Works in 3DHigh-Speed PCB Riveting Machine in Operation#smt #machine #wire  BonderS3000 Vertical Radial Insertion Machine | THT AutomationZero Defects: 50,000 Continuous Points Verified with S7020 Mixed Component InsertionVision-Corrected Terminal Insertion: 0.015 mm Automatic CorrectionCustomized SMT Gripper Nozzles - How Southern Machinery Designs and Manufactures for Smart EMSWho Carries Your Wave Soldering Pallets? Manual vs AGV ReturnSMT AGV-to-Conveyor Docking | Southern Machinery Material Transfer ConceptAutomatic 8-Core Ribbon Cable Processing Machine | Punching, Cutting, Separating & StrippingTerminal Insertion Speed: 0.6 s per Point vs Real ThroughputInline vs Offline X-Ray SMD Counter for a Lights-Out SMT WarehouseManual Wire Stripping Machine vs. Fully Automatic Wire Cutting & Stripping Machine.
SMT solution provider |

S-300B Radial Lead Molding & Taping Machine: How It Works in 3D

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER