Uploaded June 2018 | Updated November 2026, 7 hours ago
Welcome Back,
This week a Friend of mine is (or was, depending on when you are reading this) getting married. Unfortunately i was not able to attend, so i offered to make the happy couple something, my something was in the shape of this Rustic Wooden Wedding Sign.
I wanted to create something that could be replicated with some basic tool, yes i am aware that i have used some expensive equipment. However if for example you replace the band saw with a coping saw, the end result will be the same - if not better.
I started by laying out my required font and design in Excel, you could use Word, Photoshop or even pencil and paper.
If you are using a computer generated printout, scaling is important, as a rule of thumb 72 Point (font Measurement) = 1 inch or 28 Point = 1 CM approximately. This will allow you to decide how big you want your lettering to be.
After printed the lettering out, i trimmed and taped them together and used a low tack adhesive to stick them to the prepared wooden boards.
This is where i cut them out on the band saw, taking my time and staying close to the lines, minimising the amount
of sanding that needed to be done later.
After cutting was completed, i cleaned up any rough edges and then worked out my placement on the base board and attached them with dowels.
Painting came next, i started with applying a spray on undercoat, not being too careful, but ensuring a good coverage. After this had dried in was time to move on to the Accent colour, a little more care was paid to this stage, i strategically highlighted the edges of the lettering and the base, as i wanted to showcase this at a later time. again i had to wait for this stage to dry and then i could cover all previous stages with household white emulsion. again i had to wait for this coat to dry.
Finally, i could get around to adding the finishing touches, with a little gentle sanding i revealed the colours underneath giving a weathered, rustic effect. the colour choice is totally personal, as is the lettering , which can be interchangeable depending on whom your true love is.
well I hope you enjoyed this and if you are still reading all of this, thank you. see you next week.
I hope you enjoy the video.
Please Follow me on,
Instagram
instagram.com/mgmakes
Facebook
facebook.com/mg.makes.73
Find Me on Etsy
etsy.com/uk/shop/MGmakes1973
A Proud Member of
Small Workshop YouTube Makers Facebook Group
facebook.com/groups/SmallWorkshopYouTubeMakers
Makers Media Network
facebook.com/groups/MakersMediaNetwork
If you would like to Support my work, then please consider leaving me a “tip” in my paypal account - all donations will go towards future projects
paypal.com/gb/home
Mgmakes@gmail.com
Welcome Back,
This week a Friend of mine is (or was, depending on when you are reading this) getting married. Unfortunately i was not able to attend, so i offered to make the happy couple something, my something was in the shape of this Rustic Wooden Wedding Sign.
I wanted to create something that could be replicated with some basic tool, yes i am aware that i have used some expensive equipment. However if for example you replace the band saw with a coping saw, the end result will be the same - if not better.
I started by laying out my required font and design in Excel, you could use Word, Photoshop or even pencil and paper.
If you are using a computer generated printout, scaling is important, as a rule of thumb 72 Point (font Measurement) = 1 inch or 28 Point = 1 CM approximately. This will allow you to decide how big you want your lettering to be.
After printed the lettering out, i trimmed and taped them together and used a low tack adhesive to stick them to the prepared wooden boards.
This is where i cut them out on the band saw, taking my time and staying close to the lines, minimising the amount
of sanding that needed to be done later.
After cutting was completed, i cleaned up any rough edges and then worked out my placement on the base board and attached them with dowels.
Painting came next, i started with applying a spray on undercoat, not being too careful, but ensuring a good coverage. After this had dried in was time to move on to the Accent colour, a little more care was paid to this stage, i strategically highlighted the edges of the lettering and the base, as i wanted to showcase this at a later time. again i had to wait for this stage to dry and then i could cover all previous stages with household white emulsion. again i had to wait for this coat to dry.
Finally, i could get around to adding the finishing touches, with a little gentle sanding i revealed the colours underneath giving a weathered, rustic effect. the colour choice is totally personal, as is the lettering , which can be interchangeable depending on whom your true love is.
well I hope you enjoyed this and if you are still reading all of this, thank you. see you next week.
I hope you enjoy the video.
Please Follow me on,
instagram.com/mgmakes
facebook.com/mg.makes.73
Find Me on Etsy
etsy.com/uk/shop/MGmakes1973
A Proud Member of
Small Workshop YouTube Makers Facebook Group
facebook.com/groups/SmallWorkshopYouTubeMakers
Makers Media Network
facebook.com/groups/MakersMediaNetwork
If you would like to Support my work, then please consider leaving me a “tip” in my paypal account - all donations will go towards future projects
paypal.com/gb/home
Mgmakes@gmail.com










